Comparison of the suction-type and the normal-type dth drill bits in reverse circulation drilling using cfd modeling
Ters sirkülasyon sondajında kullanılan normal tip kuyudibi çekiçli matkap ucu ile emme tipi matkap ucunun hareketli akışkanlar dinamiği kullanılarak karşılaştırılması
- Tez No: 772217
- Danışmanlar: PROF. DR. HAFİZE ŞEBNEM DÜZGÜN
- Tez Türü: Yüksek Lisans
- Konular: Maden Mühendisliği ve Madencilik, Mining Engineering and Mining
- Anahtar Kelimeler: Hesaplamalı akışkanlar dinamiği (HAD), Matkap, Matkap uçları, Sondaj, Computational fluid dynamics (HAD), Auger, Twist bit, Drilling
- Yıl: 2022
- Dil: İngilizce
- Üniversite: Colorado School Of Mınes
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Mühendislik Bilimleri Ana Bilim Dalı
- Bilim Dalı: Maden Mühendisliği Bilim Dalı
- Sayfa Sayısı: Belirtilmemiş.
Özet
Reverse circulation drilling is a commonly used drilling technique in mineral exploration due to its high sampling rate and cost-efficiency. The effectiveness of this drilling technique depends on the operational parameters and the utilized drill bit type. The normal-type down-thehole (DTH) hammer bit is mainly preferred in reverse circulation drilling since it can be used either for direct circulation or reverse circulation drilling operations. A new-type drill bit named as the suction-type drill bit has been designed and developed in China to increase the efficiency of reverse circulation drilling performance. Reverse circulation drilling performance can be evaluated by the high negative pressure inside the drill bit and the suction capacity of the system. This study examines the reverse circulation drilling performances of these two types of drill bits using the Computational Fluid Dynamics (CFD) modeling. ANSYS Fluent, a CFD code, is utilized for the numerical simulations. First, three suction-type drill bits with a different number of flushing nozzles are designed and analyzed to find the optimum operational air inlet amount according to the flushing nozzle number. Then, the normal-type DTH drill bit is tested under the same operational parameters. The simulation results show that the normal-type DTH drill bit does not provide sufficient reverse circulation compared to the suction-type drill bit. The suctiontype drill bit has more negative pressure inside the drill bit and suction capacity, which leads to a better reverse circulation performance.
Özet (Çeviri)
Özet çevirisi mevcut değil.
Benzer Tezler
- Havacılıkta kullanılan bazı eksenel simetrik cisimlerin aerodinamik karakteristiklerinin teorik ve deneysel olarak incelenmesi
Theoretical and experimental investigation on aerodynamic characteristics of some bodies of revolution used in aeronautics
VEYSEL ATLI
- Betonarme yapılarda daha güçlü kolon tasarımının lineer olmayan sistem davranışına etkisi
Effects of strong column- weak beam design on non-linear beha vior of reinforced concrete frame structures
M.GÜNHAN AKSOYLU
- Aderans arttırıcı katkı maddelerinin iki eksenli yükleme altındaki tuğla duvarların kayma davranışına etkisi
The Effect of additives on the shear strength of brick masonry wall under biaxial loading
MERAL BEGİMGİL
- Beyin damar hastalığı olan hastalarda baş yüksekliğinin ve trakeal aspirasyonun beyin kan akımına etkisi
The Effect of head up position and tracheal suctioning on cerebral blood flow in stroke patients
HALİSE COŞKUN
- Sıkıştırılmış sıvı kaynaması
Subcooled boiling
ZEHİR FATİH ÖZTÜRK
Yüksek Lisans
Türkçe
1997
Nükleer Mühendislikİstanbul Teknik ÜniversitesiFizik Ana Bilim Dalı
PROF. DR. ŞARMAN GENÇAY