Geri Dön

Farklı yapı ve özelliklere sahip termoplastiklerin kırılma davranışlarında numune boyutu ve deney hızına bağlı değişimlerin incelenmesi

The Investigation of changes depending on specimen size and test speed in the fracture behaviour of thermoplastics which have different structure and properties

  1. Tez No: 126531
  2. Yazar: KENAN BÜYÜKKAYA
  3. Danışmanlar: YRD. DOÇ. DR. HALİL DEMİRER
  4. Tez Türü: Doktora
  5. Konular: Metalurji Mühendisliği, Metallurgical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2002
  8. Dil: Türkçe
  9. Üniversite: Marmara Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Metal Eğitimi Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 164

Özet

ÖZET FARKLI YAPI VE ÖZELLİKLERE SAHİP TERMOPLASTİKLERİN KIRILMA DAVRANIŞLARINDA NUMUNE BOYUTU VE DENEY HIZINA BAĞLI DEĞİŞİMLERİN İNCELENMESİ Kırılma, mekanik bileşenlerin karşılaştığı hasar modlarının başında gelmektedir. Kırılma konusunda en önemli kavram malzemelerin kırılma tokluğudur. Kırılma tokluğunun ölçümü için basit darbe ve ağırlık düşürme testleri gibi bir çok standart test uygulanmaktadır. Çatlak hattından yüklenmiş numuneler veya çift konsollu kiriş şeklindeki numunelerle kırılma tokluğu ölçümü ilk olarak yapıştırmalı bağlantılarda gerçekleştirilmiştir. Daha sonra bazı metal alaşımları üzerinde test edilen bu yöntem polimetilmetakrilat ve polistiren gibi gevrek polimerlere de uygulanarak olumlu sonuçlar alınmıştır. Bu çalışmada esas olarak çift konsollu kiriş şeklindeki numunelerin yüksek ve orta yoğunluklu polietilen ve polipropilen gibi üç farklı polimer için uygulanabilirliğinin incelenmesi hedeflenmiştir. Başlangıçtaki denemelerde numunenin literatürde verilen geometrik şekli ile bunun mümkün olmadığı görüldü ve çözüm için yapılan uzun denemelerden sonra orijinal numune geometrisi üzerinde yapılan modifikasyonlar sonunda bu malzemeler için test edilebilir yeni bir numune geometrisine ulaşıldı. Levha halindeki üç cins polimer için bu yeni geometri esas alınarak üzerinde kırılmaya kılavuzluk edecek kanallar bulunan farklı boyut ve kalınlıkta numuneler hazırlandı. Üzerlerinde değişik uzunlukta çentik açılmış olan bu numuneler farklı hızlarda MOD-I testine tabi tutuldu. Kırılmadaki maksimum yükte oluşan çatlak açılma yer değiştirmesi ölçülerek kompliyans değerleri belirlendi. Elde edilen veriler numune kompliyansının çatlak uzunluğu ile değişimini gösterecek şekilde grafikler halinde sunuldu. Sonuçların deneylerde kullanılan polimerlerin mekanik özellikleri İle uyumlu olması ulaşılan numune geometrisinin bu malzemeler için uygulanabilir olduğunu göstermiştir. Eylül 2002 Kenan BÜYÜKKAYA V

Özet (Çeviri)

ABSTRACT THE INVESTIGATION OF CHANGES DEPENDING ON SPECIMEN SIZE AND TEST SPEED IN THE FRACTURE BEHAVIOUR OF THERMOPLASTICS WHICH HAVE DIFFERENT STRUCTURE AND PROPERTIES Fracture is the main failure mode of mechanical components. Fracture toughness of materials is the most important concept in the fracture subject. Several standard test methods such as simple impact and falling weight tests are utilised for the measurement of fracture toughness. The measurement of this property with crack-line loaded or double cantilever beam specimens were first applied on adhesively bonded joints. Later this method was tested on some metal alloys. It was also applied on brittle polymers such as polymethylmetacrylate and polystyrene and positive results obtained. The main aim of this study is to investigate the applicability of the double cantilever beam specimens for three different polymers namely high and medium density polyethylene and polypropylene. In the earlier trials it was found that it was impossible to test this specimen with the geometry which was given in the literature. After long trials; modifications were made on the original specimen geometry for the solution and finally a new geometry, applicable for these materials, was obtained. By considering the new geometry for the three types of sheet polymers, different size and thickness specimens with guide grooves were prepared. These specimens which have various length notches on them were subjected to MOD-I testing under different test speeds. Compliance values were determined by measuring the crack opening displacement which corresponds to maximum load. The obtained data were presented in the form of graphs which show the change of specimen's compliance with crack lenght. The conformity of results to the mechanical properties of specimen materials showed the applicability of present specimen geometry for these materials. September 2002 Kenan BÜYÜKKAYA VI

Benzer Tezler

  1. Molecular dynamıcs analyses and experımental ınvestıgatıon ın the effects of the nanoaddıtıves on the thermo-mechanıcal propertıes and fracture toughness of bıodegradable polylactıc thermoplastıc

    Parçalanabilen polilaktik asit termoplastiklere nano katki maddelerinin ilavesinin termo-mekanik özellikleri̇ ve kırılma tokluğu üzerindeki etkilernin moleküler dinamik analizleri ve deneysel olarak incelenmesi

    BURÇAK ZEHİR

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Makine MühendisliğiAdana Alparslan Türkeş Bilim Ve Teknoloji Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ CEM BOĞA

    DR. ÖĞR. ÜYESİ MIRSADEGH SEYEDZAVVAR

  2. Investigation of the dyeability of post-consumer recycled acrylonitrile-butadiene-styrene (PCR-ABS) by using antistatic agent and plasma treatment

    Tüketici sonrası geri dönüştürülmüş akrilonitril-bütadien-stirenin (ABS) boyanabilirliğinin antistatik ajan kullanımı ve plazma işlemi vasıtasıyla incelenmesi

    AHMET BERKAY EZGÜ

    Yüksek Lisans

    İngilizce

    İngilizce

    2023

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    DOÇ. DR. MOHAMMADREZA NOFAR

  3. Alev geciktirici polimer kompozitlerin ekstrüzyon yöntemi ile hazırlanması ve karakterizasyonu

    Preparation and characterization of flame retardant polymer composites through extrusion method

    AYKUT YÜCESOY

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    Mühendislik BilimleriYıldız Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. HALE BERBER YAMAK

  4. Production and characterization of thermoplastic elastomer foams based on styrene-ethylene-butadiene-styrene and polypropylene

    Stiren-etilen-bütadien-stiren ve polipropilen bazlı köpük termoplastik elastomerlerin geliştirilmesi ve karakterizasyonu

    CEREN KIROĞLU

    Doktora

    İngilizce

    İngilizce

    2022

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. NİLGÜN KIZILCAN

  5. Characterization of baroplastics

    Baroplastiklerin karakterizasyonu

    ARİ ŞANT BİLAL

    Yüksek Lisans

    İngilizce

    İngilizce

    2011

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. METİN HAYRİ ACAR