Geri Dön

Paslanmaz ve takım çaliklerinde tane boyutunun ultrasonik dalgaların saçılmasına etkisi

Effect of grain size on the scattering of ultrasonic waves in stainless and tool steels

  1. Tez No: 184012
  2. Yazar: İLVEN MUTLU
  3. Danışmanlar: PROF. DR. ENVER OKTAY
  4. Tez Türü: Yüksek Lisans
  5. Konular: Metalurji Mühendisliği, Metallurgical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2006
  8. Dil: Türkçe
  9. Üniversite: İstanbul Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 72

Özet

F7        7   1 1   &          77 7 7                DG=1   &  6  BAD    6 77        7          77   *    7           7   6 DA;  1   &   77      7      7     B 77         1      7     .77   7        7    &  A

Özet (Çeviri)

In this study, effect of grain size on the scattering of ultrasonic waves in stainless andtool steels was investigated. The heat treatments were carried out in order to obtaindifferent grain sizes for H13 tool steel and 304 stainless steel samples. Holding timesand temperatures were varied to obtain different grain sizes. The 316 austenitic stainlesssteel samples were prepared in different grain sizes by casting. Metallographicexaminations were done on each sample and the grain sizes were determined. Ultrasonicvelocities of longitudinal and transverse waves were measured by means of pulse-echomethod using normal probes with 1, 2 and 4 MHz frequencies. Scattering of ultrasonicwaves increased with increasing grain size of the samples. Grain sizes of the sampleswere smaller than the wavelengths of the ultrasonic waves and the grainsize/wavelength ratio was near the Rayleigh region. In addition elastic and shearmodulus of the samples were determined. It was found that elastic and shear modulus ofthe samples decreased with increasing grain size.

Benzer Tezler

  1. Sürtünme kaynaklı ostenitik-martenzitik sübaplardaki nitrürasyon gevrekliliğinin incelenmesi

    Nitriding embrittlement in friction-welded austenitic-martensitic engine valves

    MEHMET KALK

    Yüksek Lisans

    Türkçe

    Türkçe

    2005

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF.DR. BARLAS ERYÜREK

  2. Farklı sıcaklıklarda menevişlenmiş ve borlama işlemine tabi tutulmuş SAE 5140 çeliğinin mekanik ve tribolojik özelliklerinin incelenmesi

    An investigation of the mechanical and tribological properties of tempered and boronized SAE 5140 steel at different temperatures

    BÜNYAMİN YAMANEL

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Makine MühendisliğiKırıkkale Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DOÇ. DR. OSMAN BİCAN

  3. Paslanmaz ve takım çeliklerine lazer yöntemiyle nanotitanyum karbür kaplanması ve aşınma davranışlarının incelenmesi

    The laser coating of stainless steel and tool steel with nanotitanium carbide and investigation of the wear behaviour coating layers

    TUNCAY ŞİMŞEK

    Yüksek Lisans

    Türkçe

    Türkçe

    2010

    Teknik EğitimGazi Üniversitesi

    Endüstriyel Teknoloji Eğitimi Ana Bilim Dalı

    PROF. DR. MAHMUT İZCİLER

  4. Borlanmış çeliklerin aşınma davranışlarının belirlenmesi

    Determination of wear attitudes of the boronized steels

    UMUT YÜNKER

    Yüksek Lisans

    Türkçe

    Türkçe

    2000

    Makine MühendisliğiCelal Bayar Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. ENVER ATİK

  5. Yüksek alaşımlı çeliklerin nitrürlenmesi

    Nitriding of high alloy steels

    OZAN AKÇAKESE

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. HÜSEYİN ÇİMENOĞLU