Geri Dön

Türkiye'de kullanılan değişik metal alaşım cinsleri üzerine pişirilen porselen materyalinin bağlanma mukavemetinin araştırılması

Başlık çevirisi mevcut değil.

  1. Tez No: 27662
  2. Yazar: METE YURTSEVEN
  3. Danışmanlar: PROF. DR. ATİLLA USER
  4. Tez Türü: Doktora
  5. Konular: Diş Hekimliği, Dentistry
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 1993
  8. Dil: Türkçe
  9. Üniversite: Ege Üniversitesi
  10. Enstitü: Sağlık Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Protetik Diş Tedavisi Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 84

Özet

ÖZET Seramik-metal restorasyonlar, porselenin estetik ve fiziksel özellikleri ile metal altyapının dayanıklılığını bünyesinde barındıran yapılardır. Bu tip restorasyonların başarısı, opak porselenin metal alaşıma olan bağlantısıyla da yakından ilgilidir. Bu bağlantının niteliği metal-porselen kombinasyonlarının düzenlenmesi açısından önem taşımaktadır. Yapılan bu çalışmada, en çok kullanılan yedi değişik metal ve bir porselenin bağlantı niteliğini belirlemek amacıyla, metal porselen bağlantısı oluşturulmuştur. Bu metal-porselen kombinasyonlarının bağlantı makaslama dirençleri, standardize edilmiş“ Shell-Nielsen çekerek makaslama testi”ile ölçülmüştür. Elde edilen bağlantı dirençleri istatistiksel analizleri ve mikroskobik incelemeleri yapılarak birbirleriyle karşılaştırmıştır. Elde edilen inceleme ve gözlem sonuçları doğrultusunda, standart yöntemle hazırlanmış metal-porselen kombinasyonları arasında bağlantı direnci açısından anlamlı farklılıklar bulunduğu ortaya konulmuştur. Buna göre, metal destekli porselen yapımında kullanılacak metal-porselen kombinasyonunun bilinçli seçimi ve preparasyon yöntemlerindeki farklılıkların dikkatle uygulanmasının restorasyonun başarısındaki etkisi önemle vurgulanmıştır.

Özet (Çeviri)

SUMMARY The use of ceramo-metal ceramic crown and bridge work is increasing yearly and in the light of clinical experience, the demand for alloys of higher strength and low cast is natural. Ceramo-metal restorations combine the beauty of porcelain and the strength of a metal substructure. The success of ceramo-metal restorations depend upon the adherence of porcelain to the ceramic alloy. Four theories of enamel adherence are mechanical, Van der Waals, chemical bonding and compressive bonding forces. Even though nonprecious alloys have superior mechanical properties, there appears to be an investigative controversy about the bond strength of nonprecious alloy systems. It has been shown that the separation of the porcelain from the metal, and the breakage between the opaque and the body porcelain were the most effective factors in the clinical success of the ceramo-metal restorations. The objective of this study is to determine the bond strength of vita porcelain with seven different non-precious alloys. In this study, seven commonly used base metal alloys were selected. A Vita VMK-68 porcelain was used for the study. Each porcelain alloys was prepared in a similar manner before porcelain application to the manufacturer's instructions. A total of 84 samples of the ceramo-metal bond was evaluated by the Shell-Nielsen test method. An instron testing machine was used to load each sample in tension until failure occured. The bond strengths were compared by statistical analysis and post-tested samples were evaluated visually and microscopically with the polarized light microscope. The results demonstrated a wide range of bond strengths. Values as low as 80.79 N/mm2 were recorded for BONDI-LOY, where as values as high as 96.70 N/mm2 were recorded for WIRON88. An analysis of variance was performed and demonstrated that there was a significant difference in bond strength among the seven alloys tested. Each metal displayed considerable variation in bond strength. Collectively, the base metal alloys evaluated displayed a disturbing tendency for adhesive failure through the porcelain-metal interface. Polarized light micrographs upon magnification at 1 0OOx, alloy BONDI-LOY exhibited a less degree of porcelain particles infrequently noted on the surface. By contrast, alloy WIRON88, presented numerous minute porcelain particles, scattered throughout the surface. Dentists have the responsability for selection of alloys used for cast restorations. This responsability should not be delegated to the dental laboratory technician, it is advisable to discuss the criteria for selection of an alloy with the technician.

Benzer Tezler

  1. Az alaşımlı krom-molibden çeliklerinin yapı kontrolü

    The Microstructure control of chromium-molybdenum low alloy steels

    BURÇİN AYDINOĞLU

    Yüksek Lisans

    Türkçe

    Türkçe

    2002

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji Mühendisliği Ana Bilim Dalı

    PROF. DR. NİYAZİ ERUSLU

  2. Hassas döküm prosesinin kalite teknik ve araçları kullanılarak optimizasyonu

    Optimisation of the investment casting process via using quality techniques and instruments

    ASLI KURUL

    Yüksek Lisans

    Türkçe

    Türkçe

    1999

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    PROF.DR. YILMAZ TAPTIK

  3. Ergimiş boraks banyosunda çeliklere vanadyum karbür kaplama

    Vc coating of steels in molten borax bath

    SEYED MOHAMMED MOUSAVİ KHOEE

    Doktora

    Türkçe

    Türkçe

    1992

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    PROF. DR. EMEL GEÇKİNLİ

  4. Çinko-alüminyum esaslı 'zamak-5' alaşımının elektroliz yoluyla tek ve çok katlı kaplanmasında önemli parametrelerin incelenmesi

    Investigation of important parameters in the mono andl multi layer eloctrolytic coating of based zinc-aluminum 'zamak-5' alloy

    RAMAZAN ÇITAK

    Yüksek Lisans

    Türkçe

    Türkçe

    1991

    Metalurji MühendisliğiGazi Üniversitesi

    Metal Eğitimi Ana Bilim Dalı

    DOÇ.DR. RAFET ARIKAN

  5. Development of iron-rich anode materials for lithium-ion battery technology from local FeCr alloys

    Yerli FeCr alaşımlarından lityum iyon pil teknolojisi için demirce zengin anot malzemelerinin geliştirilmesi

    MEHMET FERYAT GÜLCAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2020

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. SEBAHATTİN GÜRMEN

    DR. ÖĞR. ÜYESİ BİLLUR DENİZ KARAHAN