Geri Dön

The effects of feed sliver moisture content on rotor spinning performance and rotor-spun yarn properties

Başlık çevirisi mevcut değil.

  1. Tez No: 400664
  2. Yazar: GÜLDEMET BAŞAL
  3. Danışmanlar: DR. JOHN P. RUST
  4. Tez Türü: Yüksek Lisans
  5. Konular: Tekstil ve Tekstil Mühendisliği, Textile and Textile Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 1998
  8. Dil: İngilizce
  9. Üniversite: North Carolina State University
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Tekstil Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 128

Özet

Özet yok.

Özet (Çeviri)

The aim of this study was to determine if increasing feed sliver moisture content would improve spinability in rotor spinning without deteriorating yam properties. Yarns were produced at high rotor speed and low twist level Two different count rotor spun yarns (18's and 24's) were spun from 100% cotton sliver at two different feed sliver moisture contents, and at two different opening roller speeds. Results indicated that increasing moisture content reduced the number of ends down, but increased yarn unevenness, and the frequency of thin places, thick places, and neps. In addition, the yarn elongation and work-to-break results were worse at high moisture contents. Another important finding was that high opening roller speed tended to improve spinability by reducing the number of ends down. Yarn evenness and thin and thick place results were also better at the high opening roller speed in the case of fine yarn. Overall, the results suggest that feed slivers with high moisture content can provide better spinning performance in rotor spinning. In other words, high moisture content can increase the production rate of open:end rotors, thus, reducing the production cost of rotor spun yarns. However, a high moisture content also tends to deteriorate yarn evenness, the frequency of imperfections and yarn elongation results which is a disadvantage for the total economics of rotor spinning.

Benzer Tezler

  1. Biyolojik yöntemle üretilmiş gümüş nanopartikül bağlı aktif karbonun karakterizasyonu ve adsorpsiyon özelliklerinin incelenmesi

    Characterization and adsorption properties of biologically synthesized silver nanoparticle attached activated carbon

    ŞEYDA KORKMAZ

    Doktora

    Türkçe

    Türkçe

    2019

    Kimya MühendisliğiYalova Üniversitesi

    Kimya ve Süreç Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ HİKMET OKKAY

  2. Püskürtmeli kurutma ve termal bozunma prosesleri ile ZnO esaslı partiküllerin ve kompozit yapıların sentezlenmesi ve karakterizasyonu

    Characterization and synthesis of ZnO based particles and composite structures via spray drying and thermal decomposition processes

    ŞEYMA DUMAN

    Doktora

    İngilizce

    İngilizce

    2016

    Seramik Mühendisliğiİstanbul Teknik Üniversitesi

    Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı

    DOÇ. DR. BURAK ÖZKAL

  3. Çinko nanotanecik içeren polimer nanokompozit malzeme üretimi ve karakterizasyonu

    Fabrication and characterization of polymer nanocomposite materials incorporated zno nanoparticles

    ALEV AKBAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Kimya Mühendisliğiİstanbul Teknik Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. SADRİYE KÜÇÜKBAYRAK OSKAY

  4. Akrilik mikroliflerin uzun lif eğirme sisteminde işlenebilirliğinin geliştirilmesi

    Improvement of processing acrylic microfibres in long-staple spinning system

    YEŞİM İRİDAĞ

    Doktora

    Türkçe

    Türkçe

    2000

    Tekstil ve Tekstil Mühendisliğiİstanbul Teknik Üniversitesi

    PROF. DR. BÜLENT ÖZİPEK

  5. Konya İnlice epitermal altın cevherlerinin zenginleştirilmesi

    Enrichment of Konya Inlice epitermal gold ores

    AYŞE NUR DÖĞME

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Maden Mühendisliği ve Madencilikİstanbul Teknik Üniversitesi

    Cevher Hazırlama Mühendisliği Ana Bilim Dalı

    PROF. DR. ALİ GÜNEY