Geri Dön

Epoksi / MWCNT ve epoksi / BN kompozit malzemeler

Epoxy / MWCNT and epoxy / BN composite materials

  1. Tez No: 409888
  2. Yazar: HAMZA ERCAN TÜREDİ
  3. Danışmanlar: YRD. DOÇ. DR. İLKAY ÖZAYTEKİN
  4. Tez Türü: Yüksek Lisans
  5. Konular: Kimya Mühendisliği, Chemical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2015
  8. Dil: Türkçe
  9. Üniversite: Selçuk Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Kimya Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 77

Özet

Bu çalışmada, çok duvarlı karbon nanotüpleri (MWCNT) ve bor nitrür (BN) nanopartikülleri iki farklı pH ortamında setiltrimetilamonyum bromür (CTAB) ile işlevselleştirilmiştir. Kompozit hazırlamak için kullanılan MWCNT-CTAB ve BN-CTAB parçacıkları, oda sıcaklığında, bir bisfenol A (DGEBA) tipi epoksi reçinesi (ER) sistemi içinde dağıtılmıştır. Elde edilen kompozitlerin karakterizasyonu taramalı elektron mikroskobu (SEM), X-Işını kırınımı (XRD), termal gravimetri (TGA) ve mekanik testler uygulanarak yapılmıştır. Yüzey modifikasyonunun, elde edilen kompozitlerin elektriksel iletkenliklerine etkisi dört nokta tekniği ile belirlenmiştir. TGA analizi BN kompozitte önemli ölçüde, 400 ºC'nin üzerindeki sıcaklıklarda saf ER' nin termal stabilitesini arttırdığını göstermiştir. Nanokompozitlerin sertleşme derecesi, FTIR spektrumları Beer-Lambert yasası kullanılarak saf ER' ye göre değerleri yaklaşık olarak aynı hesaplanmıştır. Elde edilen kompozitlerden en iyi elektrik iletkenliği ER / MWCNT-CTAB (pH 5.5) göstermiştir. Kompozitlerin yüzey sertliği, Young modülü ve gerilme mukavemeti incelenmiştir. ER / MWCNT-CTAB (pH 5.5) kompozit yüzey sertlik değeri, diğer kompozitlere göre daha yüksek bulunmuştur. Kompozitlerin morfolojileri X-ışını kırınımı (XRD) ve taramalı elektron mikroskobu (SEM) kullanılarak karakterize edilmiş ve elde edilen sonuçlar karşılaştırılarak incelenmiştir.

Özet (Çeviri)

In this study, multi-walled carbon nanotubes (MWCNT) and boron nitride (BN) nanoparticles are functionalized with cetyltrimethylammonium bromide in two different pH environment. The MWCNT-CTAB and BN-CTAB particles are used to prepare composites at room temperature is dispersed in a bisphenol A (DGEBA) type epoxy resin system. The characterization of the obtained composite scanning electron microscope (SEM), X-Ray Diffraction (XRD), thermal gravimetric (TG) and the mechanical testing was conducted by applying. The surface modification effect on the electrical conductivity of the composite obtained was determined by a four-point technique. TGA analysis substantially of BN composite at temperatures above 400 ºC showed that increasing the thermal stability of the pure epoxy. The degree of hardening of the nanocomposite, FTIR spectra, values based on pure epoxy calculated using the Beer-Lambert law is about the same. The best electrical conductivity of the resulting composite ER / MWCNT-CTAB (pH 5.5) showed. Of composites, surface hardness, Young's modulus, tensile strength was investigated. ER / MWCNT-CTAB (pH 5.5) composite surface hardness values were higher than other composites. Morphology of composites, X-ray diffraction (XRD) and scanning electron microscopy (SEM) using-characterized and results obtained were compared.

Benzer Tezler

  1. Filaman sarım karbon elyaf/epoksi boruların dinamik davranışına karbon nanotüp ve bor nitrür nano partikül ilavesinin etkisi

    The effect of carbon nanotube and boron nitride nanoparticles addition on dynamic behaviour of filament wound carbon fiber/epoxy pipes

    SALİM EĞEMEN KARABULUT

    Doktora

    Türkçe

    Türkçe

    2017

    Makine MühendisliğiSelçuk Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. AHMET AVCI

  2. Sterolitografi ile üretilen kompozitlerde nano toz katkısının mekanik ve fiziksel özelliklere etkisinin araştırılması

    Investigation of the effect of nano powder additives on mechanical and physical properties of composites produced by stereolithography

    MAMOUN K.M. ALSHIHABI

    Yüksek Lisans

    Türkçe

    Türkçe

    2024

    Makine MühendisliğiIsparta Uygulamalı Bilimler Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ MEVLÜT YUNUS KAYACAN

  3. Uçak uçuş kontrol kumanda yüzeyleri ve havacılık nano takviyeli hibrit kompozitlerin hasar analizlerinin termografi yöntemi ile yapılabilirliğinin incelenmesi

    Investigation of the feasibility of damage analysis of airplane flight control control surfaces and aviation nano-reinforced hybrid composites using thermography method

    CAHİT BİLGİ

    Doktora

    Türkçe

    Türkçe

    2024

    Havacılık ve Uzay MühendisliğiKarabük Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. BİLGE DEMİR

  4. MWCNTs grown carbon fabric/epoxy nanocomposites and their mechanical/thermal/electrical properties

    Çok duvarlı karbon nanotüp büyütmeli karbon kumaş/epoksi nanokompozitler ve mekanik/termal/elektriksel özellikleri

    MD SYDUZZAMAN

    Doktora

    İngilizce

    İngilizce

    2022

    Tekstil ve Tekstil MühendisliğiErciyes Üniversitesi

    Tekstil Mühendisliği Ana Bilim Dalı

    PROF. DR. ABDULKADİR BİLİŞİK

  5. Synergetic effects of hybrid nanoparticles on the mechanical properties of carbon fiber reinforced epoxy nanocomposites

    Karbon elyaf takviyeli kompozitlerde hibrit nanopartikül katkısının mekanik özelliklere etkisinin incelenmesi

    ESRANUR YÜKSEL

    Yüksek Lisans

    İngilizce

    İngilizce

    2023

    Kimya Mühendisliğiİstanbul Teknik Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. HANZADE AÇMA

    DR. ÖĞR. ÜYESİ OSMAN EKSİK