Geri Dön

Halka basma deneyinde pekleşme üstelinin sürtünme kalibrasyon eğrileri üzerine etkisinin incelenmesi

Investigation of effect of the strain hardening exponent on the friction calibration curves in ring compression test

  1. Tez No: 524608
  2. Yazar: TOLGA GÜNEŞ
  3. Danışmanlar: DR. ÖĞR. ÜYESİ SUNAL AHMET PARASIZ
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2018
  8. Dil: Türkçe
  9. Üniversite: Sakarya Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Makine Tasarım ve İmalat Bilim Dalı
  13. Sayfa Sayısı: 71

Özet

Metallerin plastik şekillendirme işlemleri ve bilgisayar ortamında gerçekleştirilen benzeşimlerinin başarılı bir şekilde gerçekleştirilmesi için sürtünme davranışlarının bilinmesi gereklidir. Sürtünme, plastik şekillendirme sırasında deformasyon kuvvetini, malzeme akışını, yüzey kalitesini ve malzemenin iç yapısı gibi birçok değişkeni etkiler. Bu sebepten temas yüzeyleri arasındaki sürtünmenin bilinmesi, deformasyon işlemini daha iyi anlayabilmemiz ve açıklayabilmemiz açısından önemlidir. Kalıpla iş parçası arasındaki sürtünme katsayısının belirlenmesinde kullanılan yöntemlerden biri halka basma deneyidir. Yaygın olarak kabul gören bu deneyde, sürtünmenin sayısal olarak belirlenmesi için deney numunesinin boyutlarında meydana gelen değişim dikkate alınır. Halka basma deneyi sonucunda numunenin yüksekliğindeki yüzde azalmaya karşılık iç çapında meydana gelen yüzde değişim mevcut sürtünmenin sayısal değeri hakkında bir bilgi verir. Bu tez kapsamında halka basma deneyinin, sonlu elemanlar yöntemiyle bilgisayar ortamında benzeşimi gerçekleştirilerek sürtünme kalibrasyon eğrileri oluşturulmuştur. Malzeminin pekleşme davranışını gösteren pekleşme üstelinin sürtünme kalibrasyon eğrileri üzerinde nasıl bir etkiye sahip olduğu ortaya konulmuştur.

Özet (Çeviri)

Friction affects many variables such as deformation force, material flow, surface quality and microstructure of materials in metal forming operations Thus, It is necessary to know friction behavior of materials in metal forming processes and to perform successful simulations of these forming processes. In order to understand and predict deformation in metal forming processes, the friction between the contact surfaces should be known. Ring compression test is one of the methods that is used to determine the friction coefficient between the surfaces. In this widely accepted test, dimensional changes of the test sample are used to estimate the numerical value of the friction. As a result of the compression test, the percent change in the inner diameter with respect to the reduction in the height of the sample provides information about the numerical value of the existing friction. In this thesis, simulation of the ring compression test is performed via finite element analysis and friction calibration curves were obtained. The effect of strain hardening exponent on the friction curves is shown.

Benzer Tezler

  1. 6061 T6 alaşımının halka basma deneyinde numune boyutunun kalibrasyon eğrileri üzerine etkisinin incelenmesi

    Investigation of the effect of specimen size on the calibration curves of 6061-T6 alloy in ring compression test

    ALİ CİHAN SARAÇ

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    Makine MühendisliğiSakarya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ SUNAL AHMET PARASIZ

  2. Yığma sıcaklığının sürtünme koşullarına etkisi

    The Effects of upsetting temperatures on frictional properties

    ŞABAN ÖZMEL

    Yüksek Lisans

    Türkçe

    Türkçe

    1991

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    DOÇ.DR. MEHMET DEMİRKOL

  3. The spatial extent of size adaptation effect in peripheral vision

    Çevresel görmede boyut adaptasyonu etkisinin mekansal kapsamı

    ECEM ALTAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2019

    Psikolojiİhsan Doğramacı Bilkent Üniversitesi

    Psikoloji Ana Bilim Dalı

    DOÇ. HÜSEYİN BOYACI

  4. Analysis of tube spinning process

    Boru sıvama yönteminin analizi

    EREN CAN SARIYARLIOĞLU

    Yüksek Lisans

    İngilizce

    İngilizce

    2021

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. MUSTAFA BAKKAL

    DR. ÖĞR. ÜYESİ ÖMER MUSIC

  5. Alçı numunelerin tek eksenli basma dayanımına, ısı etkisi

    Temperature effects on gypsium samples

    MUSTAFA YAVUZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2005

    Maden Mühendisliği ve MadencilikSelçuk Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF.DR. KEMAL GÖKAY