Bakır, pirinç ve St37 malzemelerinin farklı bileşimlere sahip tellerle lehiminde mekanik ve metalurjik özelliklerin incelenmesi
The examination of mechanical and metallurgical properties in filler with different compositions for brazing of copper, brass and St37 materials
- Tez No: 558827
- Danışmanlar: DR. ÖĞR. ÜYESİ SİMGE İRİZALP
- Tez Türü: Yüksek Lisans
- Konular: Mühendislik Bilimleri, Engineering Sciences
- Anahtar Kelimeler: Sert lehimleme, Ag esaslı dolgu metali, mikroyapı, Brazing, Ag based filler metal, microstructure
- Yıl: 2019
- Dil: Türkçe
- Üniversite: Manisa Celal Bayar Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Konstrüksiyon ve İmalat Bilim Dalı
- Sayfa Sayısı: 131
Özet
Bu tez kapsamında; soğutucu sistemlerin üretiminde sert lehimleme ile birleştirilen bakır-pirinç, pirinç-pirinç ve pirinç-çelik malzemelerin lehimleme esnasında kullanılan dolgu metalindeki Ag içeriğinin değiştirilmesi ile hem dayanımı yüksek hem de uygun maliyetli bir birleştirme elde edilmesi hedeflenerek farklı Ag seviyelerine sahip dolgu metallerinden en uygun olanları belirlenmiştir. Özellikle bakır borular iklimlendirme sektöründe, soğutucu sistemlerde sıklıkla kullanılır. Soğutucu sistemlerin üretimi esnasında bakır boruların birleşimi ürünün ömrü ve kalitesi bakımından oldukça önemlidir. İstenilen kalitede birleştirmeyi sağlarken; sıcaklık, ilerleme hızı gibi parametrelerin yanında kullanılan lehim telinin içindeki elementlerin oranı büyük önem taşımaktadır. Lehim tellerinin maliyetlerini genellikle içindeki gümüş oranları etkiler. Örneğin içerisinde hiç Ag elementi olmayan bir bakır esaslı tel, içinde %40 Ag elementi bulunan bir telden yaklaşık 20 kat daha ucuzdur. Amaç kaliteden ödün vermeden daha ucuz lehimleme yapmak olduğunda lehim teli içindeki Ag oranı oldukça kritiktir. Bu çalışmada, 3 farklı malzeme çifti, 5 farklı Ag oranı içeren dolgu metali kullanılarak sert lehimleme prosesi gerçekleştirilmiştir. Patlatma testi ile hasara uğradığı gerilmenin büyüklüğü tespit edilmiş öte yandan mikrosertlik testleri ve metalürjik incelemelerle karakterizasyon çalışmaları gerçekleştirilmiştir. Sert lehimleme prosesinde özellikleri iyileştiren Ag seviyesi tespit edilerek malzeme performansının iyileşmesi yanında maliyetinde azaltılması hedeflenmiştir. Son olarak, bu tez Ag içeren sert lehim dolgu metallerini analiz ederek, Ag içeriğini azaltmaya yönelik bir çalışma ortaya koymuş ve ileriye dönük daha fazla araştırma için temel bir zemin sunmuştur.
Özet (Çeviri)
Within the scope of this thesis; In the production of refrigeration systems, the most suitable filler metals with different levels of Ag were determined by changing the content of Ag in the filler metal used during brazing of brass-brass and brass-steel materials combined with brazing. Especially copper pipes are frequently used in air-conditioning sector and cooling systems. The combination of copper pipes during the production of cooling systems is very important in terms of product life and quality. While providing the desired quality of the combination; In addition to the parameters such as temperature, feed rate, the ratio of the elements in the solder wire is of great importance. The cost of solder wires usually affects the silver proportions in it. For example, a copper-based wire with no Ag elements is about 20 times less expensive than a wire with 40% Ag element. When the aim is to make the brazing cheaper without sacrificing quality, the ratio of Ag in the solder wire is critical. In this study, the brazing process was carried out by using 3 different material pairs, 5 different Ag ratio filler metal. The magnitude of the stress that it was damaged by the blasting test was determined. On the other hand, microhardness tests and characterization studies were carried out by metallurgical investigations. The level of Ag, which improves the properties in the brazing process, is determined and it is aimed to reduce the material performance and reduce the cost. Finally, this thesis analyzes the Ag-containing brazing filler metals, introducing a study to reduce the content of Ag and provides a basis for further prospective research.
Benzer Tezler
- Bakır ve pirinç boru ikili malzeme gruplarının sürtünme karıştırma kaynak yöntemi ile birleştirilmesi
The joining of brass and copper pipe dual-material groups via the friction stir welding method
NERMİN KAHRAMAN
Yüksek Lisans
Türkçe
2007
Bilim ve TeknolojiErciyes ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. EYYUP GERÇEKCİOĞLU
- Cu,Zn, pirinç ve Fe'nin sulu çözeltilerdeki korozyon davranışları üzerine fosfat iyonlarının etkileri
The Effect of phosphate Ions (PO4-3) on the corrosion of Cu,Zn, brass and Fe in aqueous solutions
GÜRAY KILINÇÇEKER
- Meyve atıkları ile zenginleştirilmiş gluten içermeyen yeni ekmeklerin geliştirilmesi
Development of gluten-free new breads enriched with fruit wastes
BURCU ERSOY
Yüksek Lisans
Türkçe
2023
Beslenme ve DiyetetikNuh Naci Yazgan ÜniversitesiBeslenme ve Diyetetik Ana Bilim Dalı
PROF. DR. NERİMAN İNANÇ
DR. ÖĞR. ÜYESİ ZEHRA GÜLSÜNOĞLU KONUŞKAN
- Pirinç ve bronz malzemelerin yüksek sıcaklıkta deformasyonu
The Deformation of brass and bronze materials at high temperatures
ŞEVKET TUNÇ ALNIAK
Yüksek Lisans
Türkçe
2004
Makine MühendisliğiGazi ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. BEDRİ TUÇ
- Seramik partikül takviyeli pirinç matris kompozitlerin spark plazma sinterleme (SPS) yöntemiyle üretimi ve karakterizasyonu
Production and characterization of ceramic particle reinforced brass matrix composites with spark plasma sintering (SPS) method
PELİN ÇAĞIM TOKAT BİRGİN
Doktora
Türkçe
2021
Metalurji MühendisliğiKütahya Dumlupınar ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. VELİ UZ
PROF. DR. REMZİ GÖREN