Epoksi/EPDM kauçuğu atığı-karbon siyahı hibrit kompozitleri
Epoxy/EPDM-carbon black hybrid composites
- Tez No: 558873
- Danışmanlar: PROF. DR. GÜLNARE AHMETLİ
- Tez Türü: Yüksek Lisans
- Konular: Polimer Bilim ve Teknolojisi, Polymer Science and Technology
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: Türkçe
- Üniversite: Selçuk Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Kimya Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 68
Özet
EPDM (etilen propilen dien monomer) önemli bir sentetik kauçuk olup birçok farklı sektörde kullanılmaktadır. Kullanım miktarındaki artışa paralel olarak EPDM atığı ortaya çıkmaktadır. EPDM atıkları, çapraz bağlanmalarından dolayı tekrar eritilip tekrar işlenme ihtimaline sahip değildir ve plastik endüstrisi için önemli bir kayıp olup genellikle yakıt olarak tüketilmektedir. EPDM kalıntılarının değerlendirilmesinin bir başka yöntemi, bunları küçük boyutlara getirerek farklı polimerlere eklemektir. Bu çalışmanın amacı atık EPDM tozunun karbon siyahı (KS) ile birlikte epoksi reçinede dolgu olarak kullanmak ve hibrit kompozitlerin mekanik, termal ve su sorpsiyonu özellikleri üzerindeki etkisini araştırmaktır. Üç farklı oranda (1:1, 1:3 ve 3:1) KS ile karışımı oluşturulan EPDM, farklı oranlarda (%5, %10, %15, %20 ve % 30) bisfenol-A tipi epoksi reçineye eklenerek kompozitleri oluşturulmuştur. Test numuneleri bu karışımlardan ASTM D 638 standarlarına göre kalıplama ile hazırlanmıştır. Kompozitlere çekme, sertlik ve su sorpsiyonu testleri uygulanmış, TGA ve SEM analizleri yapılmıştır. En yüksek çekme dayanımına 3:1 EPDM-KS kompozitleri sahip olmuş, bu kompozitlerin çekme dayanımları 115.5-158.6 MPa aralığında değişmiştir. En yüksek yoğunluk (1.16 g/cm3) kütlece %5 hibrit dolgu oranındaki 1:3 EPDM-KS kompozitinde, en düşük yoğunluk (1.03 g/cm3) kütlece %30'luk 3:1 EPDM-KS kompozitinde görülmüştür. EPDM-KS hibrit dolgusu kompozitlerin termal dayanımını artırmış, su sorpsiyonunu ise azaltmıştır.
Özet (Çeviri)
EPDM (ethylene propylene diene monomer) is an important synthetic rubber and is used in many different sectors. In parallel with the increase in the amount of usage, EPDM waste occurs. Due to the irrevesible cross-linking processes are unfeasible. EPDM waste constitutes a significant role for the plastic industry and is usually consumed in the form of fuel. Another method of evaluation of EPDM residues is to add them to different polymers by bringing them into small dimensions. The aim of this study is to use waste EPDM powder with carbon black (KS) as an epoxy resin filler and to investigate the effect of hybrid composites on mechanical, thermal and water sorption properties. EPDM mixed with KS in three different ratios (1: 1, 1: 3 and 3: 1) was added to bisphenol-A type epoxy resin in different proportions (5%, 10%, 15%, 20% and 30%) to form composites. Test samples were prepared from these mixtures by molding according to ASTM D 638 standards. Tensile, hardness and water sorption tests were applied to the composites and TGA and SEM analyses were performed. The highest tensile strength of 3: 1 EPDM-KS composites had the tensile strength of 115.5-158.6 MPa. The highest density (1.16 g / cm3) was observed in the 1: 3 EPDM-KS composite with 5% hybrid filler ratio, while the lowest density (1.03 g / cm3) was observed in the 3: 1 EPDM-KS composite of 30% by mass. EPDM-KS hybrid filler improved thermal strength and decreased water sorption of composites.
Benzer Tezler
- Lastik ve EPDM kauçuğu atıklarının kompozit malzemede kullanımı
Using of tire and EPDM rubber wastes in composite materials
MERVE TÜRKBEN
Yüksek Lisans
Türkçe
2019
Polimer Bilim ve TeknolojisiKonya Teknik ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
PROF. DR. GÜLNARE AHMETLİ
- Preparation of polybenzoxazine-EPDM rubber based hydrophobic nanocomposite materials
Polibenzokzazin-EPDM kauçuk esaslı hidrofobik nanokomozit malzemelerin hazırlanması
EBRU KURTARAN
Yüksek Lisans
İngilizce
2023
Bilim ve TeknolojiSakarya ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
PROF. DR. SEFER CEM OKUMUŞ
PROF. DR. UĞURSOY OLGUN
- Electrospinning of super tough nylon 6,6 fibers and their use in layered composites
Süper tok naylon 6,6 fiberlerin elektroeğrilmesi ve katmanlı kompozitlerde kullanımı
ALİCAN KARA
Yüksek Lisans
İngilizce
2023
Makine MühendisliğiHacettepe ÜniversitesiFen Bilimleri Ana Bilim Dalı
PROF. DR. BORA MAVİŞ
- Improvement of mechanical characteristics of the thermoset epoxy polymer systems by using nanostructures
Epoksi termoset polimer sistemlerin mekanik karakteristiklerinin nanoyapılar kullanılarak geliştirilmesi
ZAFER AZEM
Doktora
İngilizce
2022
Metalurji MühendisliğiDokuz Eylül ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
PROF. DR. UĞUR MALAYOĞLU
- Epoksi kaplamalarda farklı katkılar kullanarak elektriksel, termal ve mekanik özelliklerin geliştirilmesi
Improvement of electrical, thermal and mechanical properties of the epoxy coatings by using different additives
FUNDA DENİZ
Yüksek Lisans
Türkçe
2023
Metalurji MühendisliğiDokuz Eylül ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DOÇ. AYLİN ZİYLAN