Tufal katkılı Pe matrisli kompozitlerin tribolojik ve mekanik özelliklerinin incelenmesi
Investigation of the tribological and mechanical properties of the oxi̇de layer (Fe2O3) additive pe matrix composites
- Tez No: 610040
- Danışmanlar: DOÇ. DR. BİLAL DEMİREL
- Tez Türü: Yüksek Lisans
- Konular: Mühendislik Bilimleri, Engineering Sciences
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2020
- Dil: Türkçe
- Üniversite: Erciyes Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 142
Özet
Polimer matrisli kompozit (PMK) malzemeler yüksek mekanik dayanım, sertlik, hafiflik gibi üstün özelliklerinden dolayı havacılık ve uzay sanayisinden günlük yaşamımıza kadar uzanan çok geniş bir alanda kullanım alanına sahiptir. Ancak PMK'nın mekanik ve tribolojik özellikleri takviye malzemesinin özellikleri ile sıkı bir şekilde ilişkilidir. Bugüne kadar da polimerler matris içerisine çok çeşitli dolgu maddesi katkılandırılmıştır. Bu çalışmada Tufal'in (FE2O3)Polietilenin (PE) potansiyel mekanik ve aşınma dayanımı performansına etkisinin incelenmesi tezin ana fikrini oluşturmaktadır. Tez çalışmasında PE/Tufal kompozit peletleri polimer matris içerisine farklı ağırlık oranlarında (%10, 20, 30, 40) ve tane boyutlarında (30, 60, 90, 120, 200 µ) Tufal eklenerek çift vidalı ekstrüder kullanılarak üretilmiştir. Ardından tribolojik ve mekanik testlerin gerçekleştirilebilmesi için üretilen peletler enjeksiyon kalıplama yöntemi ile kalıplanmıştır. PE/Fe2O3kompozitlerinebaşlıca çekme, Shore D sertlik ölçümü, dinamik mekanik analiz, termal analiz, yapısal analizler (XRF, XRD, SEM vb.) ve kuru ortamda pin-on-disk aşınma testleri, gerçekleştirilmiştir. Tüm bu testlerde süre, yük, aşınma hızı gibi faktörlerin yanı sıra temel olarak kompozitlerin takviye fazı tane boyutu ve takviye fazı % bileşimi parametrelerinin etkileri araştırılmıştır.Ayrıca kompozitlerde aşınma sonrası yüzey optik mikroskop görüntüleri incelenerek aşınma mekanizmaları yorumlanmıştır. Kompozitlerin sertlik değerleri ve elektriksel direnci üzerine Fe2O3'in tane boyutunun etkisi gözlenmezken artan Fe2O3konsantrasyonu ile artış elde edilmiştir.Fe2O3'in yapıya ilavesinin artışı çekme dayanımı üzerinde belirgin bir etkiye neden olmazken, kopma uzamasının takviye oranının artışı ile arttığı tespit edilmiştir.
Özet (Çeviri)
Polymer matrix composite (PMK) materials have a wide range of applications ranging from aerospace industry to daily life due to their high mechanical strength, hardness and light weight. However, the mechanical and tribological properties of PMK are closely related to the properties of the reinforcing material. To date, a wide variety of fillers have been incorporated into the polymers matrix. The main idea of this thesis is to investigate the effect of Tufal (FE2O3) on the potential mechanical and abrasion resistance performance of polyethylene (PE). In the thesis, PE / Tufal composite pellets were produced by using twin screw extruder in different weight ratios (10, 20, 30, 40) and grain sizes (30, 60, 90, 120, 200 µ) into the polymer matrix. The pellets were then molded by injection molding to perform tribological and mechanical tests. Tensile, Shore D hardness measurement, dynamic mechanical analysis, thermal analysis, structural analysis (XRF, XRD, SEM, etc.) and pin-on-disk abrasion tests were performed on PE / Fe2O3 composites.In all these tests, the effects of the parameters such as duration, load, abrasion rate as well as reinforcement phase particle size and reinforcement phase % composition of the composites were investigated. The optical microscope images of the composites surfaces were also investigated and their wear mechanisms were interpreted. No effect of grain size of Fe2O3 on the hardness values and electrical resistance of the composites was observed, but increasing Fe2O3 concentration has improved them. While the addition of Fe 2 O 3 to the structure does not cause any significant effect on the tensile strength, it is seen that the elongation at brake increases with increasing Fe2O3 concentration.
Benzer Tezler
- Nano malzeme içeren çimentolu kompozitlerin termal verimliliği
The investigation of thermal efficiency of nano additive included cement composites
ADAR KARAGÖZ
Yüksek Lisans
Türkçe
2018
Bilim ve TeknolojiDokuz Eylül ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
DOÇ. DR. EGEMEN TEOMETE
- Yerli hammaddelerden üretilen M tipi stronsiyum hekzaferrit (SrO.6Fe2O3) mıknatısın özelliklerinin katkı maddeleriyle geliştirilmesi
Improving the properties of M type strontium hexaferrite (SrO.6Fe2O3) magnet synthesized using local raw materials by substitution compounds
BURAK YALÇIN
Yüksek Lisans
Türkçe
2015
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA KELAMİ ŞEŞEN
- Molibden katkılı nano-akışkan soğutma sıvısının AISI 5140 çeliğinin frezelenme performansına etkilerinin farklı soğutma sıvıları ile karşılaştırılarak araştırılması
Investigation of the effects of molybdenum added nano-fluid coolant on the milling performance of AISI 5140 steel in comparison with different coolants
TUFAN ZEROOĞLU
Yüksek Lisans
Türkçe
2024
Makine MühendisliğiBingöl ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ ÜNAL DEĞİRMENCİ
- Hamsi atıklarından antimikrobiyal ve antioksidan katkılı yenilebilir film üretimi ve hamsi filetolarında kullanımı
Antioxidant and antimicrobial added edible film production from anchovy (Engraulis encrasicolus) wastes and application to anchovy fillets
SERPİL TURAL
Doktora
Türkçe
2016
Gıda MühendisliğiOndokuz Mayıs ÜniversitesiGıda Mühendisliği Ana Bilim Dalı
DOÇ. DR. SADETTİN TURHAN
- VO2+ ve Cu2+ iyonu katkılandırılmış oksalatlı ve sitratlı bileşiklerin EPR ve optik absorpsiyon incelemesi
EPR and optical absorption study of Vo2+ and Cu2+ doped of oxalates and citrates compounds
AYŞE TUFAN
Yüksek Lisans
Türkçe
2006
Fizik ve Fizik MühendisliğiOndokuz Mayıs ÜniversitesiAtom ve Molekül Fiziği Ana Bilim Dalı
Y.DOÇ.DR. BÜNYAMİN KARABULUT