ŞEFFAF VEYA HAFİF OKSİT DIŞI BALİSTİK SERAMİKLERİN GELİŞTİRİLMESİ
ŞEFFAF VEYA HAFİF OKSİT DIŞI BALİSTİK SERAMİKLERİN GELİŞTİRİLMESİ
- Tez No: 899253
- Danışmanlar: PROF. DR. SERVET TURAN
- Tez Türü: Doktora
- Konular: Savunma ve Savunma Teknolojileri, Bilim ve Teknoloji, Seramik Mühendisliği, Defense and Defense Technologies, Science and Technology, Ceramic Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2024
- Dil: Türkçe
- Üniversite: Eskişehir Teknik Üniversitesi
- Enstitü: Lisansüstü Eğitim Enstitüsü
- Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Günümüzde hızla gelişen savunma sanayi teknolojileriyle birlikte daha tehlikeli tehditler ortaya çıkmaktadır. Yeni tehditler, balistik korumanın iyileştirilmesi ihtiyacını ortaya koymaktadır. Yüksek kalibreli ve yüksek hızda hareket edebilen, sert ve ağır çekirdekler içeren zırh delici mermilerin yaygınlaşması sonucunda Seviye IV koruma sağlayacak seramik zırhların üretilmesi zorunlu hale geldi. Balistik zırhlar koruyacağı alana göre ihtiyaçları değişmektedir. Vizör ve sensörlerin korumasında şeffaflık önemli iken personel korumasında hafiflik ve maliyet önemlidir. Bu tezin amacı hızla gelişen tehditlere karşı silisyum karbür - bor karbür (SiC-B4C) kompozit zırh malzemelerinin basınçsız sinterleme tekniği ile üretilmesi ve test edilmesi, yüksek sertlik ve kırılma tokluğuna sahip SiC-B4C-TiB2 kompozitinin sıcak dövme tekniği ile özelliklerinin iyileştirilmesi ve şeffaf AlON zırh seramiğinin tozdan nihai ürüne üretim teknolojisinin geliştirilmesidir. Şeffaf AlON üretiminde öncelikli olarak karbotermal nitridasyon tekniği ile AlON tozu üretilip, CaCO3 katkısı ile basınçsız sinterlenebilirliği incelenmiştir. Sıcak pres tekniği ve/veya sıvı faz kullanılarak sinterlenebilen SiC-B4C zırh malzemesi, bu çalışmada, basınçsız katı-hal sinterleme ile üretim prosesi geliştirilmiştir. Yüksek sertlik ve balistik performansa sahip kompozit üretilmiştir. SiC-B4C-TiB2 kompozitinin sinterlenmesi CeO2 sıvı fazı ile gerçekleştirip devamında sıcak dövme işlemine tabi tutularak malzemenin sertlik ve eğilme mukavemeti başta olmak üzere mekanik özelliklerden ödün verilmeden kırılma tokluğu artırılırken, sıcak dövme sonrası kompozit içerisinde oluşan grafitin yönelimine bağlı olarak ısı iletkenliği iki katına çıkarılmıştır.
Özet (Çeviri)
Nowadays, more dangerous threats emerge with rapidly developing defense industry technologies. New threats reveal the need to improve ballistic protection. As a result of the widespread use of armor-piercing bullets containing hard and heavy cores that can move at high caliber and high speed, it has become necessary to produce ceramic armor that will provide Level IV protection. Ballistic armor needs vary depending on the area it will protect. While transparency is important in protecting viewfinders and sensors, lightness and cost are important in personnel protection. The aim of this thesis is to produce and test SiC-B4C composite armor material with pressureless sintering technique against rapidly developing threats, to develop SiC-B4C-TiB2 composite with high hardness and fracture toughness by hot forging technique, and to develop transparent AlON armor ceramic starting from powder. In the transparent ceramic study, the feasibility of producing AlON powder by carbothermal nitridation technique and pressureless sintering with CaCO3 additive was examined. While SiC-B4C armor material is produced by hot press technique, in this study, the material, which can be sintered using liquid phase in the literature, was produced and developed with high hardness and ballistic performance by pressureless solid-state sintering. By sintering the SiC-B4C-TiB2 composite with CeO2 liquid phase and subsequently subjecting it to the hot forging process, the fracture toughness of the material is increased without compromising the mechanical properties, especially the hardness and bending strength, while the thermal conductivity was doubled depending on the orientation of in-situ formed graphite after hot forging.
Benzer Tezler
- An experimental investigation of high purity single walled carbon nanotubes as transparent electrode materials
Tek duvarlı karbon nanotüp saflaştırması ve geçirgen elektrot oluşturulması konusunda deneysel çalışmalar
MOZHGAN LAKI
Yüksek Lisans
İngilizce
2015
Enerjiİstanbul Teknik ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
DOÇ. DR. ELİF ÜLKÜ ARICI
- Growth and characterization of ZnSnO thin films on polymers for OLEDs
Oled'ler için polimerler üzerine znsno ince filminin büyütülmesi ve karakterizasyonu
MERVE EKMEKÇİOĞLU
Yüksek Lisans
İngilizce
2019
Fizik ve Fizik Mühendisliğiİzmir Yüksek Teknoloji EnstitüsüFizik Ana Bilim Dalı
DOÇ. DR. GÜLNUR AYGÜN ÖZYÜZER
- ŞEFFAF PLAKLARLA YAPILAN ORTODONTİK TEDAVİLERDE KULLANILAN ÇEŞİTLİ AYGITLARIN DENTAL EKSPANSİYON ÜZERİNE ETKİSİNİN SONLU ELEMANLAR İLE DEĞERLENDİRİLMESİ
EVALUATION OF THE EFFECTS OF VARIOUS APPLIANCES USED IN ORTHODONTIC TREATMENT WITH CLEAR ALIGNERS ON DENTAL EXPANSION BY FINITE ELEMENT ANALYSIS
MEHMET KIZILOĞLU
Doktora
Türkçe
2026
Diş Hekimliğiİstanbul Aydın ÜniversitesiOrtodonti Ana Bilim Dalı
DOÇ. AYLİN PAŞAOĞLU BOZKURT
- Evaluation of the effects of different clear aligner cleaning methods on microbial colonization
Farkli şeffaf plak temizleme yöntemlerinin mikrobiyal kolonizasyon üzerine etkilerinin incelenmesi
SEVAN HARZİVARTYAN
Doktora
İngilizce
2025
Diş HekimliğiMarmara ÜniversitesiOrtodonti Ana Bilim Dalı
DOÇ. DR. HANİFE NURAY YILMAZ
- Clear aligner apareyinin etkinliğinin belirlenmesi
A prospective clinical study to determine the efficiency of clear aligner appliance
ASLIHAN YILDIRIM
Doktora
Türkçe
2013
Diş Hekimliğiİstanbul ÜniversitesiOrtodonti Ana Bilim Dalı
PROF. DR. YILDIZ ÖZTÜRK ORTAN