Geri Dön

Dynamic forces and hole quality in drilling process

Delme işleminde dinamik kuvvetler ve delik kalitesi

  1. Tez No: 151315
  2. Yazar: MÜGE PİRTİNİ
  3. Danışmanlar: Y.DOÇ.DR. İSMAİL LAZOĞLU
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2004
  8. Dil: İngilizce
  9. Üniversite: Koç Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 112

Özet

Özet yok.

Özet (Çeviri)

ABSTRACT Drilling is one of the most commonly used machining processes in various industries such as automotive, aircraft and aerospace, dies/molds, home appliance, medical and electronic equipment industries. Due to the increasing competitiveness in the market, cycle times of the drilling processes must be decreased. Moreover, tight geometric tolerance requirements in designs, drilled hole precisions must be increased in production. On the other hand, process engineers have to be conservative when selecting machining conditions with respect to metal removal rate in order to avoid undesirable cases such as drill breakage, excessive cutter deflection and undesirable hole profile problems. In this research, a new mathematical model based on the mechanics and dynamics of the drilling process is developed for the predictions of cutting forces and hole qualities in advance. A novel method is also proposed in order to obtain cutting coefficients directly from a set of relatively simple calibration tests. The model is able to simulate the cutting forces for various cutting conditions in the process planning stage. In structural dynamics module, measured frequency response functions of the spindle and the tool system are integrated into the model in order to obtain drilled hole profiles. Therefore, in addition to predicting the forces, the new model allows to determine and visualize drilled hole profiles in 3D and to select parameters properly under the manufacturing and tolerance constraints. Extensive number of experiments is performed to validate the theoretical model outputs with the measured force and CMM hole profiles. It is observed that model predictions agree well with the force and CMM measurements.

Benzer Tezler

  1. Talaşlı imalatta görüntü işleme metodu ile takım sehimi tespiti ve hata analizi

    Tool deflection detection and error analysis with image processing method in machining

    BURAK ÖZDEMİR

    Doktora

    Türkçe

    Türkçe

    2021

    Makine Mühendisliğiİnönü Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DOÇ. DR. ERKAN BAHÇE

  2. Karbon elyaf takviyeli kompozit borularda delik delme işleminin mekanik ve yorulma davranışları üzerindeki etkisinin araştırılması

    Investigation on the effect of drilling process on mechanical and fatigue behaviour in carbon fiber reinforced composite pipes

    SEZER MORKAVUK

    Doktora

    Türkçe

    Türkçe

    2023

    Makine MühendisliğiAfyon Kocatepe Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. KUBİLAY ASLANTAŞ

    PROF. DR. UĞUR KÖKLÜ

  3. Development of flat bottom drill cutting tool for machining of brass alloys

    Pirinç alaşımlarının talaşlı imalat süreçleri için düz ağızlı matkap kesici takım geliştirilmesi

    NIMA ZOGHIPOUR

    Doktora

    İngilizce

    İngilizce

    2023

    Makine MühendisliğiMarmara Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. YUSUF KAYNAK

  4. Ezme ile tamamlanan deliklerde ezme payının yüzey kalitesine etkisi

    Effect of roller burnishing share on surface quality in holes completed by roller burnishing

    BARIŞ BURAK AYDOĞAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiGazi Üniversitesi

    Endüstriyel Tasarım Mühendisliği Ana Bilim Dalı

    PROF. DR. ADNAN AKKURT

  5. Performance prediction and optimization of raise boring machines (RBMs)

    Başyukarı delme makinelerinin (BDM) performanslarının tahmini ve optimizasyonu

    AYDIN SHATERPOUR MAMAGHANI

    Doktora

    İngilizce

    İngilizce

    2022

    Maden Mühendisliği ve Madencilikİstanbul Teknik Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF. DR. HANİFİ ÇOPUR