Geri Dön

Preparation and characteriza SEBS-clay nanocomposites

SEBS(Stiren-b-etilen-b-bütilen-stiren)-kil nanokompozitlerin hazırlanması ve karakterizasyonu

  1. Tez No: 152819
  2. Yazar: MESUT ÜNAL
  3. Danışmanlar: PROF.DR. YUSUF ZİYA MENCELOĞLU
  4. Tez Türü: Yüksek Lisans
  5. Konular: Kimya, Chemistry
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2004
  8. Dil: İngilizce
  9. Üniversite: Sabancı Üniversitesi
  10. Enstitü: Mühendislik ve Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Kimya Bölümü
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 60

Özet

ÖZET Bu çalışma nispeten ekonomik, kimyasal yüzey aktif kimyasallarla, daha verimli ve kolay ama endüstriyel anlamda uygulama şansı en yüksek ve üstün özelliklere sahip SEBS (stiren-b-etilen-b-bütilen-b-stiren)-kil (sodium montmorillonit) nanokompozitleri oluşturmayı amaçlamaktadır. Eriyik interkalasyon ve yerinde interkalatif polymerizasyon metodu birleştirilerek alternatif bir metod denenmiştir. Araştırma kil yüzeyinin ve tabakalar arası boşluğunun verimli bir biçimde modifiye edilip, uygun metodla nanokompozit sentezleme metodu bulmaya odaklanmıştır. Bu çalışmada yenilik oluşturan düşünce yüzey aktif malzemeler gibi davranan polimerizasyon başlaücılannın nanokompozit hazırlama tekniklerine dahil edilmesidir, interkalatif polimerizasyon, verimli yüzey aktif madde-başlatıcı kombinasyonu varlığında kil modifikasyonundan sonra, bu ürünün masterbatch-nanokompozit (stiren-sodyum montmorillonite) haline dönüştürülmesinde kullanılmıştır. Daha sonra bu SEBS ile daha uyumlu bir yapı oluşturacağına inandığımız masterbatch dolgusuz SEBS kompoundu ile eriyik halde kanştınlmıştır. Oluşan nanokompozitin özellikleri diğer tekniklerle hazırlanan numunelerle karşdaştırılmıştır. Başlatıcı olarak kullanılan suda çözünen azo-başlatıcı 2,2'-Azobis(2-metil- propionamid) (V-50) kuarternize edilmiş ve reaksiyonun gerçekleği DSC ve ^-NMR ile teyid edilmiştir. DSC termograflan modifiye edilmemiş başaltıcıya ait 173.9 "C'deki erime noktasının 119.5 °C'ye düştüğünü göstermiştir. Daha sonra x-ışını difroktometre analizi esasına göre en uygun yüzeyaktif madde kombinasyonu belirlenmiştir. Kil tabakaları arasındaki mesafe Braggs Kanunundan ivfaydalanarak denenen bütün yüzey aktif maddeler için hesaplanmıştır. Sodyum montmorillinit'teki bu mesafe Tequart DSM (N-N dialkil dimetil ammonyum klorit).ile modifiye edilen kilde, ilk hali olan 1.2 nm'den 1.9 nm'ye çıkmıştır. Bu değer BTC 1218-50 (Alkil dimetil benzil ammonyum klorit) ile deney tekrarlandığında 1.4 nm civarında seyretmiş, ticari olarak üretilmiş Cloisite 15A'da ise 1.38 olarak hesaplanmıştır. Molar eşitlikle hazırlanmış Tequart DSM-modifiye edilmiş V-50 (MCI) kombinasyonunda ise bu rakam 2.35 nm'dir. Diğer kombinasyonların iyon değiştirme tekniği ile kil tabakalarını birbirinden uzaklaştırabilme değerleri şöyle özetlenebilir: Tequart DSM- V-50 (MC6), 2.02 nm; BTC 1218-50-modifiye edilmiş V-50 (MC4), 1.07 nm, ve BTC 1218-50-V-50 (MC2), 1.07 nm. Çalışmanın son bölümü SEBS ürününden ve MCI adlı kilden çeşitli metodlarla nanokompozit sentezlenmesini kapsamaktadır. Her deney sonucu oluşan numuneler kompresyon kalıplama yöntemiyle oluşturulup karşılaştırma amaçlı testlere tabii tutulmuştur. Termogravimetrik analiz yöntemiyle numunelerin ihtiva ettikleri kil numuneleri teyid edilmiştir. Çekme-kopma testi sonucunda bütün nanokompozitlerde kopmada uzama değeri dolgusuz ürüne göre artmış kopma mukavemeti ise azalmıştır. Malzemenin içindeki kil miktarı arttıkça kopmda uzama edeğeri düşmüştür. Maleik anhidrit graft edilmiş SEBS (SEBS-MA) ihtiva eden numune en yüksek uzama değerine ulaşmıştır (642,87%). Bizim yeniliğimizi temsil eden MCI masterbatch (%25 kil) (MC1-MB) nanokompoziti (% 5 Mİ), yapısında daha fazla stiren polimeri içermesine rağmen MCI 'in olduğu gibi kullanıldığı %5 kil ihtiva eden numune karşılaştırıldığında daha fazla uzadı. Masterbatch hazırlama yoluyla veya maleik anhidrit kullanılarak arttmlan kompetibilizasyon kopmada uzama değerlerini yükseltmiştir. Masterbatch tekniği yapıya eklediği ekstra polistiren yüzünden aynı zamanda kopma mukavemetini yükseltmiştir. SEM imajları ise x-ışını difraktometresi ölçümleriyle aynı doğrultuda oluşan nanokompozitin interkalatif olduğunu ispatlamış aynı zamanda kil parçacıklarının polimer matriksine homojen dağılımını göstermiştir.

Özet (Çeviri)

ABSTRACT In this study, SEBS (styrene-b-ethylene-b-butylene-styrene) clay nanocomposites were synthesized with easy-to-find, cheap ingredients and using convenient, efficient and commercially viable methods. In particular, a combined melt intercalation method and in- situ intercalative polymerization method was implemented to produce nanocomposites. The underlying strategy of this approach was to treat clays with appropriately chosen surfactants, namely, those that posessed the ability to intercaltate the basal spacings of the clay. An added subtlety of this study was the incorporation of an engineered polymerization initiator in the nanocomposite preparation, which behaved as an effective surfactant and permitted the uniform initiation of polymerization from even within basal spacings as opposed to being restricted to the clay surface. In the first part of this study, the optimum surfactant for a given reaction condition was determined to be Tequart DSM (N-N dialkyl dimethyl ammonium chloride). Basal spacings noted via WAXD analysis showed that Na-MMT treated with Tequart DSM had reached values of up to 1.9 nm, which exceeded the value of 1.2 nm that is typical of pristine clay. Notably, Tequart DSM delaminated more effectively than Cloisite 15 A, a commercial organoclay (1.38 nm). BTC 1218-50 (Alkyl dimethyl benzyl ammonium chloride) was also succesful in view that the value noted was about 1.4 nm. Subsequently, an appropriate surfactant-initiator was envisaged and afforded by methylating the water- soluble radical initiator, V-50 (2,2'-Azobis-2-methyl propionamide). Methylation was confirmed by the appearance of additional resonances on the H-NMR spectrum and by the shift of the melting curve from 173.9 °C to 1 19.5 °C on the DSC thermogram. While NMR analysis indicated that an average of four methyl groups had been attached to the native structure, DSC thermograms implied high product purity in view that the new melting endotherm was sharp. By applying this in-situ intercalative polymerization strategy to the nbest surfactant and initiator pair, a Styrene-clay nanocomposite masterbatch was realized. Clay, modified using an equimolar ratio of Tequart DSM and methylated V-50, displayed the greatest interlayer distance of 2.35 nm when characterized using WAXD. While this sample (MCI) gave the best results, the interlayer spacings of other preparations were also notable: Tequart DSM-native V-50 (MC6) gave 2.02 nm, BTC 1218-50-treated V-50 (MC4) gave 1.07 nm, and BTC 1218-50-untreated V-50 (MC2) gave 1.07 nm. In the final part of the thesis, several approaches for the preparation of nanocomposites were tested on a standard unfilled SEBS grade material. Each attempt was melt-mixed with SEBS and compression molded plaques were tested. Thermogravimetric analyses were carried out primarily to verify the anticipated clay content in each of the blends. SEM images in agreement with WAXD data proved that the nanocomposite produced was in fact intercalative. Tensile testing of polymer blends containing 5wt% intercalated clays displayed greater elongation values in all of the nanocomposites when compared with unfilled SEBS. For example, the maleic anhydride grafted SEBS (SEBS- MA) sample had the highest elongation value (642,87%). The sample representing our strategy, namely, a MCI masterbatch (MC1-MB) containing nanocomposite, was more easily elongated than MCI 5% clay samples, even though it contained more styrene. Another interesting finding was the decreased tensile strength of the nanocomposities when compared to unfilled SEBS. Lastly, as the clay content was increased, the maximum elongation values were found to decrease. To summarize, the combined melt intercalation method and in-situ intercalative polymerization method did indeed afford nanocomposites with altered properties. Compatibilization through masterbatch preparation or SEBS-MA incorporation consistently improved maximum elongation values. The masterbatch technique also improved the tensile strength of nanocomposites, the reason being apparently related to the extra styrene content in matrix. It follows to reason that the continued development of such an intercalative strategy can greatly improve the compatibility and properties of a wide range of composite materials. in

Benzer Tezler

  1. Haloysit nanotüp dolgu malzemesi ile termoplastik ve termoplastik elastomer polimer matris kompozit malzemelerin hazırlanması ve karakterizasyonu

    Preparation and characterization of halloysite filled thermoplastic and thermoplastic elastomer composite materials

    TUĞÇE ÖNER

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Mühendislik Bilimleriİstanbul Teknik Üniversitesi

    Metalurji Mühendisliği Ana Bilim Dalı

    PROF. DR. BURAK ÖZKAL

  2. Poli(laktik asit) karışımlarının hazırlanması ve karakterizasyonu

    Preparation and characterization of poly(lactic acid) blends

    İBRAHİM EKİZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    Polimer Bilim ve TeknolojisiYalova Üniversitesi

    Polimer Malzeme Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ HATİCE AYLİN KARAHAN TOPRAKÇI

  3. Polystyrene-based and carbon fabric-reinforced polymer composites containing carbon canotubes: Preparation, modification and characterization

    Polistiren bazlı ve karbon kumaş ile güçlendirilmiş karbon nanotüp içeren polimer kompozitleri: Hazırlanması, modifikasyonu ve karakterizasyonu

    BERRAK ERKMEN

    Doktora

    İngilizce

    İngilizce

    2020

    Kimya MühendisliğiOrta Doğu Teknik Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. GÖKNUR BAYRAM

  4. Otomotiv uygulamaları için yüzey özellikleri iyileştirilen polipropilen kompozitlerin hazırlanması ve karakterizasyonu

    Preparation of polypropylene composites being cured their surface characteristics for automotive application and it's characterization

    NESLİHAN ERGÜN

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    Polimer Bilim ve TeknolojisiYalova Üniversitesi

    Polimer Mühendisliği Ana Bilim Dalı

    PROF. DR. HÜSEYİN YILDIRIM

  5. Streptozotosin ile deneysel diabet oluşturulan hayvanlarda bazı kan parametrelerinin incelenmesi

    Başlık çevirisi yok

    BELKİS ÜNVER

    Yüksek Lisans

    Türkçe

    Türkçe

    1986

    BiyokimyaMarmara Üniversitesi

    Biyokimya Ana Bilim Dalı

    DOÇ. DR. NESRİN EMEKLİ