Pompalarda yüzey pürüzlülüğünün ve kaçakların performans üzerindeki etkilerinin incelenmesi
Research of the affects of surface roughness and loses on pumps's performance
- Tez No: 202251
- Danışmanlar: PROF. DR. İRFAN KARAGÖZ
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2006
- Dil: Türkçe
- Üniversite: Uludağ Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 102
Özet
Santrifüj pompa dizaynlarında çok özel durumlar dısında, hedef maksimum verime ulasabilmektir. Pompa verimindeki yüzdesel olarak saglanan çok az artıslar dahi, uzun süre çalısan, özellikle yüksek güçlerde motor kullanan pompalarda toplamda yüksek enerji tasarrufları saglamaktadır. Bu hedef dogrultusunda fan ve gövde yapıları dizayn edilirken, bazı diger faktörlerde pompaların verimlerini etkilemektedir.Bu faktörlerden bir tanesi de pompa malzemesi ve malzeme ile döküm kalitesine baglı olan yüzey pürüzlülügüdür. Yüzey pürüzlülügü, sadece malzemeye baglı olmayıp, isleme ve döküm kalitesine de baglıdır. Bu çalısmada, gövde malzemesi GG25 olan bir yatay santrifüj pompada, yüzey pürüzlülükleri farklı olan 3 farklı malzemeden çark kullanılarak yapılan deneylerle, pompa veriminin nasıl degistigi test edilmistir. Aynı pompa gövdesinde, bronz, AISI316 Paslanmaz çelik ve GG25 Döküm demir malzemeden çarklar 6sar farklı çalısma noktasında test edilmistir.Her noktadaki basma yüksekligi ve debi degerleri ile pompa motorunun çektigi amper ölçülmüs, motor verimi de dikkate alınarak, verim egrileri çizilmistir. Bu çizimlerden sonra yüzey pürüzlülügünün verim üzerinde etkisi oldugu tespit edilmistir. Çalısmalar göstermistir ki, pompa çarkının yüzey pürüzlülügünün düsürülmesi pozitif olarak yüzdesel verimi etkilemektedir. Anahtar Kelimeler ; Santrifüj, pompa, verim, yüzey pürüzlülügü, hidrolik kaçaklar, enerji tasarrufu, çark.
Özet (Çeviri)
In the design of cantrifugal pumps, except in very special conditions, the aim is always to reach the maximum efficiency. Even a little increase in rational efficiency, especially in the pumps those work long time per day with a high power motors, provides high energy savings. Due to this aim not only the design of the impellers and the volute but there are some other parameters those affect the pump efficiency.One of these parameters is the pump material and the surface roughness which depends on this material, and the moulding quality. Surface roughness does not only depend on the material but it also depends on the quality of moulding and mechanical treatment. In this study, some tests have been done on a horizontal centrifugal pump which has a GG25 volute by using 3 different impellers which are made by different materials and the efficiency has been determined. In the same pump volute, bronze, AISI316 stainless steel and GG25 impellers have been tested on 6 different operating points for each.On each operating point, the head, flow and the amperage have been measured and by taking the motors efficiency into consideration, the efficiency curves have been drawn. After obtaining the efficiency curves, it has been noticed that the surface roughness has effected the pump efficiency. As a conclusion of the investigations, reducing the surface roughness of the impeller, effects the pump efficiency positevely. Key Words ; Centrifugal, pump, efficiency, surface roughness,hydrolic losses, energy saving, impeller.
Benzer Tezler
- Verim iyileştirilmesi için optimize edilen ve poliüretan kaplama yapılan pompa çarkının sayısal ve deneysel analizi
Experimental and numerical investigation of an optimized pump impeller with polyurethane surface coating effect for efficiency improvement
OSMAN KOCAASLAN
Yüksek Lisans
Türkçe
2015
EnerjiSelçuk ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. MUAMMER ÖZGÖREN
- Termiyonik Vakum Ark (TVA) ile depolanan katkısız ve P2O5, CdO ve ZnO katkılı V2O5 ince filmlerin bazı özelliklerinin incelenmesi
Investigation of some properties of undoped and P2O5, CdO, and ZnO doped V2O5 thin films deposited by the Thermionic Vacuum Arc (TVA)
ÇAĞRI DURMUŞ
Doktora
Türkçe
2024
Fizik ve Fizik MühendisliğiEskişehir Osmangazi ÜniversitesiFizik Ana Bilim Dalı
PROF. DR. TAMER AKAN
- Kaymalı yataklarda yüzey pürüzlülüğünün yağlamaya etkilerinin deneysel analizi
Experimental analysis of the effects of surface roughness on lubrication in thrust bearings
FİKRET KOÇ
- The effect of thrust bearing surface roughness on circulator pumps performance
Eksenel yatak yüzey pürüzlülüğünün pompa performansına etkisi
MURAT ÖZGENÇ
Yüksek Lisans
İngilizce
2024
Makine MühendisliğiMarmara ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. BÜLENT EKİCİ
DR. ÖĞR. ÜYESİ AYBALA YILDIRIM
- Santrifüj pompa performansının sayısal analizi
Numerical analysis of centrifugal pump performance
MEHMET KAYA
Yüksek Lisans
Türkçe
2009
Enerjiİstanbul Teknik ÜniversitesiEnerji Bilim ve Teknoloji Ana Bilim Dalı
PROF. DR. MURAT AYDIN