Isıl püskürtme yöntemi ile oluşturulan martenzitik paslanmaz çelik kompozit toz kaplamanın mikroyapı ve mekanik özelliklerinin incelenmesi
Investigation of microstructure and mechanical proparties of martensitic stainless powder based coatings formed by thermal spray method
- Tez No: 238813
- Danışmanlar: YRD. DOÇ. DR. RAMAZAN SAMUR
- Tez Türü: Yüksek Lisans
- Konular: Metalurji Mühendisliği, Teknik Eğitim, Metallurgical Engineering, Technical Education
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2008
- Dil: Türkçe
- Üniversite: Marmara Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metal Eğitimi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 128
Özet
Günümüzde endüstrinin en önemli problemlerinden birisi, üretim makinalarında meydana gelen aşınma arızalarıdır.Üretim sistemi otomasyona doğru gittikçe birim zamanda üretim miktarları da artmaktadır. Bu nedenle bakım ve onarım büyük önem kazanmaktadır. Çünkü hareketli parçalardaki aşınma ve ortamın etkisinden dolayı oluşan korozyondan doğan kayıplar ekonomik açıdan büyük değerler oluşturmaktadır.Bu zararlardan korunmak için metal yüzeyi çeşitli yöntemlerle kaplanır. Yapılacak kaplamanın cinsi metale, ortama, daha sonra yapılacak imalat işlemlerine, parçanın şekli ve boyutuna bağlıdır. Kaplamalar fiziksel, kimyasal ve elektrokimyasal olmak üzere üç ana guruba ayrılır. Parçaların aşınma dayanımını artırmak için ısıl püskürtme metodu ile temas yüzeyleri kaplanır. Isıl püskürtme kaplamaların ana çalışma prensibi ergimiş ve/veya kısmen ergimiş metallerin kuvvetli gaz basıncı altında altlık malzemeye püskürtme işlemine dayanır.Bu çalışmanın amacı metallerin aşınmaya, korozyona karşı korunabilmesi ve dekoratif özellik kazandırılması için metale ısıl püskürtme yöntemiyle oluşturulan martenzitik paslanmaz çelik toz esaslı kaplamanın, mikroyapı ve mekanik özelliklerinin incelenmesidir.Bu çalışmada kullanılan ısıl püskürtme yöntemi fiziksel bir yöntemdir. Kaplanan numunelerin sertlik incelemeleri , vikers sertlik ölçme yöntemine göre incelenmiş ve numunelerin yüzeyinin ve kesitinin altlık metale göre serlik değerlerindeki değişiklikler analiz edilmiştir. Kaplanan numunelerin bağ mukavemeti incelenerek; ara bağlayıcılı kaplama, ara bağlayıcısız kaplama ile karşılaştırılmış ve analiz edilmiştir.
Özet (Çeviri)
Today, the wear failure of production machines is one of the most important problems of the industry.Application of automation in production results in increases in productivity. In order to achieve a continuous production, maintenance of equipment becomes very important. Wearing of moving parts and corrosion losses mean irreversible financial problems.In order to protect the surfaces from the wear failure, the surfaces are coated by different methods. The type of coating material depends on the substrate, the working conditions of machine, finishing operations on the coating surfaces and shape and dimensions of the product. Coatings are divided into three main groups: physical, chemical and electrochemical. To increase the wear resistance, contact surfaces of parts are coated by thermal spray method. The basic principle of thermal spray method is to spray molten or semi-molten coating material onto the substrate under high gas pressure.The aim of this study is to investigate the microstructure and mechanical properties of martensitic stainless steel powder based coatings applied by thermal spray to obtain wear, corrosion resistant and decorative surfaces.In this study thermal spray method is used. The temper studies of the covered samples have been analyzed to viders temper meterage method and it has also been analyzed to the changes in the temper considering the underlay metallic of the section and the surface of these samples.By being analyzed of the connector resistance of the covered samples,the interspace connector coverage and the coverage without interspace connector have been compared and analyzed.
Benzer Tezler
- Isıl püskürtme yöntemiyle oluşturulan molibden ve molibden esaslı kaplamanın mikroyapı ve mekanik özelliklerinin incelenmesi
Investigation of microstructure and mechanical properties of molibden and molibden based coatings formed by thermal spray method
İBRAHİM ŞENER
Yüksek Lisans
Türkçe
2004
Metalurji MühendisliğiMarmara ÜniversitesiMetal Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. RAMAZAN SAMUR
- Alüminyum üzerinde ısıl püskürtme yöntemiyle oluşturulan çelik kaplamaların aşınma davranışlarının incelenmesi
An Investigaion of wear behavior of steel coatings performed by thermal spraying on aluminum
GÖKHAN KİPER
Yüksek Lisans
Türkçe
2003
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. HÜSEYİN ÇİMENOĞLU
- CeO2-TiO2(CeO2-ZrO2) ince filmlerinin oluşturulması, optik yapısal ve bazı elektrokimyasal özelliklerinin incelenmesi
Preparation and investigation of optical, structural and some electrochemical properties of CeO2-TiO2(CeO2-ZrO2) thin films
FARHAD E GHODSİ
- An experimental investigation of high purity single walled carbon nanotubes as transparent electrode materials
Tek duvarlı karbon nanotüp saflaştırması ve geçirgen elektrot oluşturulması konusunda deneysel çalışmalar
MOZHGAN LAKI
Yüksek Lisans
İngilizce
2015
Enerjiİstanbul Teknik ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
DOÇ. DR. ELİF ÜLKÜ ARICI
- Farklı azot akış hızına sahip ortamlarda ısıl işlem uygulanmış ultrasonik sprey piroliz yöntemiyle oluşturulan sn-katkılı indiyum oksit ince filmlerin fiziksel ve optik özelliklerinin incelenmesi
Investigation of physical and optical properties sn-doped indium oxide thin films fabricated by ultrasonic spray pyrolysis method and heat treatment under different nitrogen flow rate atmospheres
MURAT KOÇ
Doktora
Türkçe
2018
Fizik ve Fizik MühendisliğiSüleyman Demirel ÜniversitesiFizik Ana Bilim Dalı
PROF. DR. MURAT ÖZTÜRK
DR. ÖĞR. ÜYESİ MURAT KALELİ