Farklı maksimum sıcaklık değerleri altında buhar kürü uygulamasının çelik lifli betonların mekanik dayanımına etkisi
The effect of different values of maximum temperature steam cure application on concretes with steel fiber
- Tez No: 293206
- Danışmanlar: DOÇ. DR. ÜLKÜ SULTAN KESKİN
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2013
- Dil: Türkçe
- Üniversite: Selçuk Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 161
Özet
Bu çalışmada, çelik tel fiberli ve kimyasal katkılı betonların mekanik dayanımları dört farklı parametre altında incelenmiştir. Bu parametrelerden ilki, betonların sınıfı olup, biri C20, diğeri C35 olmak üzere iki farklı sınıfa sahip beton numuneler üretilmiştir. İkinci parametre, üretilecek betonlarda kullanılacak olan çelik tel fiber miktarıdır. Her iki beton sınıfı için ayrı ayrı 25 kg/m3 ve 40 kg/m3 çelik tel fiber içeren beton karışımları hazırlanmıştır. Ayrıca, karşılaştırma yapılabilmesi açısından, her iki beton sınıfında da çelik tel fiber içermeyen beton karışımları da hazırlanmıştır. Üçüncü parametre, betona üretimden sonra üç farklı kür uygulamasıdır. Numunelere su, hava ve buhar kürü uygulanmıştır. Dördüncü parametre olarak ise, buhar kürü uygulamasında iki farklı maksimum sıcaklık değeri (650C ve 850C) uygulanmıştır. Tüm bu parametreler ile çelik tel fiber içeren beton dayanımına buhar kürünün etkisinin araştırılması amaçlanmıştır. Bu amaçla; iki farklı beton sınıfı için toplam 270 adet 15cmx15cmx15cm boyutunda küp numune, 81 adet 15cmx15cmx75cm prizmatik numune üretilmiştir. 270 adet küp numunenin 162 adedi buhar kürüne, 54 adedi su kürüne, 54 adedi hava kürüne; 81 adet prizmatik numunenin 54 adedi buhar kürüne, 27 adedi su kürüne tabi tutulmuşlardır. Sonuçta çeşitli sınıflardaki ve farklı çelik lif oranlarındaki katkılı beton numunelere uygulanan buhar kürü uygulamasının, beton basınç ve eğilme dayanımı üzerindeki etkisi incelenmiştir.
Özet (Çeviri)
In this study, the mechanical strengths of the concretes with steel fibers and chemical additives were examined under four different parameters. Concrete class was the first parameter that concrete specimens for the normal strength of C20 concrete class and for the high strength of C35 concrete class were produced. The second parameter was the steel fiber amount inside the concrete specimens that concrete mixtures including the steel fibers of 25 kg/m3 and 40 kg/m3 were prepared separately for both concrete classes. Additionally, in order to make comparison, there were prepared concrete specimens not including any steel fibers for both concrete classes. The third parameter was about the three different curing processes (water, air and steam) applied on the concrete specimens after their productions. Finally, the fourth parameter was the application two different maximum temperature values (65oC and 85oC)during the steam curing process. The objective of these parameters was to investigate the effect of steam curing on the strength of the concrete specimens including steel fibers. Fort his purpose; 270 cubic concrete specimens of 15cm×15cm×15cm dimensions and 81 concrete beam specimens of 15cm×15cm×75cm dimensions were produced for both concrete classes.While 162 of 270 cubic specimens were subjected to steam curing, 54 to water curing and 54 to air curing; 54 of 81 beam specimens were subjected to steam curing and 27 to water curing. As a conclusion,the effect of steam curing application on the compression and bending strength values of the concrete specimens with additives of various steel fiber ratios was investigated for different concrete classes.
Benzer Tezler
- A study on the effect of pressure on in situ combustion kinetics of Bati Raman crude by conventional and isoconventional methods
Batı Raman petrolünün yerinde yanma kinetiğine basıncın etkisinin alışılagelmiş ve eşdönüşüm yöntemleri ile incelenmesi
EVANS ANTO-DARKWAH
Yüksek Lisans
İngilizce
2015
Petrol ve Doğal Gaz Mühendisliğiİstanbul Teknik ÜniversitesiPetrol ve Doğal Gaz Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. MURAT ÇINAR
- Santrifüj kuvvet altında tekstil içerisindeki su hareketinin incelenmesi
Investigation of water flow in porous textile under centrifugal forces
FATİH KASAP
Doktora
Türkçe
2018
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA ÖZDEMİR
- Çok doymamış yağ asitleri bakımından zengin alg ilave edilen yemlerin levrek (Dicentrarchus albrax L., 1758)'de büyüme performansı ve vücut komposizyonuna etkisi
Effects of pufa (Polyunsaturated fatty acids) enriched algae added diets on growth and body composition of sea bass (Dicentrarchus labrax L., 1758)
KAMİL MERT ERYALÇIN
Yüksek Lisans
Türkçe
2006
Su Ürünleriİstanbul ÜniversitesiSu Ürünleri Yetiştiriciliği Ana Bilim Dalı
PROF. DR. ERDAL ŞENER
- Sulama amaçlı bir barajın optimum işletme modelinin belirlenmesi
Determination of optimal operation model for an irrigation reservoir
SABAHATTİN IŞIK
- Context-aware remote sensing data processing for improvement of agricultural predictions
Bağlam farkındalıklı uzaktan algılama veri entegrasyonu ile tarımsal tahminlerin iyileştirilmesi
AYDA FITRIYE AKTAŞ
Doktora
İngilizce
2024
Bilgisayar Mühendisliği Bilimleri-Bilgisayar ve Kontrolİstanbul Teknik Üniversitesiİletişim Sistemleri Ana Bilim Dalı
PROF. DR. BURAK BERK ÜSTÜNDAĞ