Influence of halloysite nanotubes on the mechanical and thermal properties of EPDM nanocomposites
Haloysit nanotüplerinin EPDM nanokompozitlerin mekanik ve termal özelliklerine etkisi
- Tez No: 362598
- Danışmanlar: PROF. DR. NURSELİ UYANIK
- Tez Türü: Yüksek Lisans
- Konular: Polimer Bilim ve Teknolojisi, Polymer Science and Technology
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2014
- Dil: İngilizce
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Polimer Bilim ve Teknolojisi Bölümü
- Bilim Dalı: Polimer Bilim ve Teknolojisi Ana Bilim Dalı
- Sayfa Sayısı: 106
Özet
Sentetik terpolimer kauçuk etilen propilen dien monomer (EPDM), %40-%80 arası etilen ve %0-%10 arası etiliden norbornen (ENB) içermektedir. Etilen oranı arttıkça kristalinite; ENB oranı arttıkça kürleşme hızı artar. EPDM kauçukların elektrik yalıtımında iyi olmaları ve buna ilaveten ısı, UV, ozon ve oksidasyona karşı dirençlerinin de yüksek olması avantajlı bir durumdur. Haloysit gibi nano boyutlu katkı maddeleri kauçuklar için takviye edici ajanlar olarak kullanılmaktadır. Bu çalışmada etilen ve dien oranları farklı olan iki çeşit EPDM (Keltan 778Z ve Keltan 6950) kullanılmıştır. Her bir EPDM çeşidi için 4 ayrı örnek hazırlanmış; HNT oranları 0-40 phr aralığında tutulmuştur. Alınan test sonuçları örneklerdeki etilen ve HNT içeriklerine göre değişkenlik göstermiştir. Peroksitle yapılan kürleştirme işleminde, kürleştirme ajanı olarak Perkadox 14-40B kullanılmıştır. Kürleşme özellikleri Moving Die Rheometer (MDR) kullanılarak incelenmiştir. HNT'lerin çukur tübüler yapısının genişlikleri her bir EPDM/HNT nanokompozit örneği için X-Ray kırınım cihazı kullanılarak tayin edilmiştir. Nanokompozitlerin termal özellikleri Termal Gravimetrik Analiz (TGA) yöntemiyle gözlemlenmiştir. EPDM/HNT nanokompozitlerinin kopma mukavemeti, kopma uzaması, elastisite modülü, sertlik ve kompresyon set özellikleri çeşitli mekanik testler uygulanarak elde edilmiştir. Test sonuçlarına göre EPDM/HNT nanokompozitlerinin kopma mukavemeti, kopma uzaması, elastisite modülü gibi mekanik özellikleri gelişme göstermiştir.
Özet (Çeviri)
Ethylene propylene diene monomer (EPDM) is a type of synthetic terpolymer rubber which is an elastomer. The ethylene content (C2) is generally between 40%-80%. The diene content is generally between 0%-10%. Increasing of C2 ratio value contributes to crystallinity of EPDM. Higher level of the diene monomer (ethylidene norbornene-ENB) brings about faster cure rate. EPDM rubbers have good resistance to heat, UV, ozone, and oxidation. Halloysite nanotubes (HNTs) with large aspect ratio improve mechanical and thermal properties of polymers as nano additive. In this work, two kinds of EPDMs (Keltan 778Z and Keltan 6950), which had different C2 and ENB ratios, were used for the nanocomposite samples productions. HNTs with 0 - 40 phr values were added to the EPDM rubber samples. The test results were evaluated depending on the C2 ratios of EPDM and the contents of HNTs in the nanocomposites. For peroxy curing, Perkadox 14-40B was used and curing properties of samples were examined by Moving Die Rheometer (MDR). X-Ray diffraction analysis (XRD) of HNTs and EPDM/HNTs nanocomposites was performed to see the basal spacing of the HNTs before and after blending with EPDM. The effects of HNTs loading on both EPDM/HNTs nanocomposites were characterized mechanically and thermally. Thermal gravimetric analysis (TGA) was used to determine the thermal properties of nanocomposite samples. Mechanical properties of nanocomposites samples were examined by using different mechanical tests to calculate the tensile modulus, tensile strength, elongation at break, hardness, deformation by compression and ageing. According to the test results, EPDM/HNTs nanocomposites showed enhanced properties such as; higher tensile modulus, tensile strength, and elongation at break values relative to unfilled EPDM.
Benzer Tezler
- Haloysit nanotüp dolgu malzemesi ile termoplastik ve termoplastik elastomer polimer matris kompozit malzemelerin hazırlanması ve karakterizasyonu
Preparation and characterization of halloysite filled thermoplastic and thermoplastic elastomer composite materials
TUĞÇE ÖNER
Yüksek Lisans
Türkçe
2019
Mühendislik Bilimleriİstanbul Teknik ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. BURAK ÖZKAL
- Processing by electrospinning method and characterization of poly(lactic acid) and poly(lactic acid)-based composite nanofibers
Poli(laktik asit) ve poli(laktik asit) bazlı kompozit nanofiberlerin elektroeğirme metodu ile prosesi ve karakterizasyonu
EMİNE ÜMRAN AŞCI
Yüksek Lisans
İngilizce
2022
Kimya MühendisliğiOrta Doğu Teknik ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
PROF. DR. GÖKNUR BAYRAM
- Flame retardancy of polymer nanocomposites
Polimer nanokompozitlerin alevlenme dayanımı
NİHAT ALİ IŞITMAN
Doktora
İngilizce
2012
Polimer Bilim ve TeknolojisiOrta Doğu Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Bölümü
PROF. DR. CEVDET KAYNAK
- Fabrication and characterization of polyvinylidene fluoride based hollow fiber ultrafiltration membranes blended with nanoparticles
Nanoparçacık katkılı poliviniliden florür esaslı delikli elyaf ultrafiltrasyon membranlarının üretimi ve karakterizasyonu
YAPRAK SUBAŞI
Yüksek Lisans
İngilizce
2018
Polimer Bilim ve TeknolojisiYıldız Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. BUĞRA ÇİÇEK
- Halloysit nanotüp destekli vanadyum nanokompozit: Üretimi, karakterizasyonu ve katalitik aktivitesi
Halloysite nanotube supported vanadium nanocomposite: Fabrication, characterization, and catalytic activity
AZİZE GÖKÇE ADAK ÇAKMAKÇI