Geri Dön

Improvements for chip-chip interconnects and mems packaging through materials and processing research

Başlık çevirisi mevcut değil.

  1. Tez No: 403007
  2. Yazar: ERDAL UZUNLAR
  3. Danışmanlar: DR. PAUL A. KOHL
  4. Tez Türü: Doktora
  5. Konular: Biyokimya, Kimya, Biochemistry, Chemistry
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2015
  8. Dil: İngilizce
  9. Üniversite: Georgia Institute of Technology
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 148

Özet

Özet yok.

Özet (Çeviri)

The work presented in this dissertation focuses on improvements for ever-evolving modern microelectronic technology. As the microelectronics technology progresses, new challenges in materials and processing are faced and need to be resolved. Improvements in metallization, packaging and the materials used in these processes can further enable reducing cost, and attaining higher performance. Specifically, three topics were investigated in this work: electroless copper deposition on printed wiring boards (PWBs), polymer-based air-gap microelectromechanical systems (MEMS) packaging technology, and thermal stability enhancement in sacrificial polymers, such as poly(propylene carbonate) (PPC). Electroless copper is important in the fabrication of electronic substrates for the formation of dense copper wiring traces on printed wiring boards (PWBs). Electroless copper deposition on PWB materials currently uses costly Pd-based catalysts. The conventional surface pretreatment of PWBs by swell-and-etch method increases the surface roughness dramatically, which leads to high conductor losses that limit the signal propagation speed and integrity between chips on PWB substrates. In that regard, low-cost and equally active Ag-based catalysts, and non-roughening surface treatment methods using mineral acids were investigated for improved electroless copper deposition processes. MEMS packaging plays an important role in protecting MEMS devices, in preserving device performance and in the final product cost. The industrial standard of wafer capping is a heterogeneous process that requires careful alignment of MEMS and capping wafers and bonding at high temperatures which might damage the devices and integrated circuits (ICs). Monolithic, wafer-level, IC-compatible and low-temperature packaging technologies need to be developed to reduce cost and improve reliability. In order to address this challenge, a polymer-based air-gap MEMS packaging technology was investigated, which uses a sacrificial polymer, PPC, to create an air-gap by thermal decomposition around the MEMS device, enclosed with a polymeric overcoat, BCB. The air-gap technology relies on the sacrificial polymer, such as PPC, that provides a temporary place-holder for micro cavity creation. The selection of materials and processing conditions in air-gap technology are often limited by the decomposition temperature of PPC, implying the requirement to control or fine-tune PPC thermal stability. For that reason, the thermal stability enhancement of PPC by Cu(I) ions previously reported was investigated to further understand its mechanism. In the electroless copper deposition study, we investigated an electroless copper deposition technique on an unclad epoxy laminate substrate, composed of a H2SO4 surface pretreatment, Sn/Ag nano-colloidal catalyst seeding, and immersion in a formaldehyde copper electroless bath. The lower cost and similar catalytic activity of Ag compared to Pd for formaldehyde oxidation makes Ag a rational catalyst choice for electroless copper deposition. It was found that the H2SO4 treatment cleaned the substrate of its impurities and provided the adhesion of the catalyst and electroless copper without increasing the surface roughness. Surface pretreatment with H2SO4 was unique in catalyst seeding, compared to other acid treatments including HCl and H3PO4. The sulfate content adsorbed on the epoxy laminate after H2SO4 treatment enabled Sn(II) sensitization by electrostatic attraction. The measured adhesion strength of deposited electroless copper layers indicated that even though H2SO4 treatment did not increase surface roughness, adhesion was still dependent on the existing initial surface roughness of the substrate. X-ray photoelectron spectroscopy (XPS) results showed Sn(II) oxidation to Sn(IV) and Ag(I) reduction to Ag(0), so as to form a core-shell nano-colloidal catalyst with Ag(0) core and SnO2 shell. It was plausible to consider some residual Sn(II) complexing with chloride ions to form SnCl3ˉ on the outer surface of nano-colloids and preventing agglomeration. Sn/Ag nano-colloids were observed to well catalyze the electroless copper deposition reaction at a practical rate. The chemical adhesion was promoted by H2SO4 treatment rather than mechanical adhesion, and the use of Sn/Ag catalyst with H2SO4 surface treatment facilitated adherent, continuous and uniform electroless copper layers on epoxy laminates. In the MEMS packaging study, a polymer-based air-gap MEMS packaging approach was investigated to reduce the cost, to simplify the packaging process and to analyze the polymeric residue. The idea was to achieve wide (~2.5x3.2 mm) and tall (10-20 μm) air-gaps to provide size-compatible packaging to MEMS devices, such as accelerometers and gyroscopes. The study provides a framework for size-compatible and clean air-gap formation by selecting the type of PPC, optimizing thermal treatment steps, identifying air-gap formation options, assessing air-gap formation performance, and analyzing the chemical composition of residue. BCB was identified as a PPC-compatible overcoat material providing excellent mechanical stability to air-gap structures. A kinetic comparison was done between PPC decomposition and BCB curing processes to determine the optimal thermal treatment recipe. It was found that the optimal treatment is a two-step heating process that includes a BCB curing at a lower temperature in the first step, and PPC decomposition at a higher temperature. Two air-gap formation processes, RIE process (uses non-photosensitive PPC) and direct photopatterning process (uses photosensitive PPC), were proposed depending on how the PPC was patterned. Less residue and more reliable air-gap structures were obtained using the RIE process. The direct photopatterning process was simpler, however a greater amount of residue was observed due to photoacid generator (PAG), at least twice the residue in the RIE process. Comparison of two-layer PPC structures with both photosensitive and non-photosensitive PPC layers revealed that it was possible to obtain reliable air-gap structures only if the photosensitive PPC was the bottom layer. Nanoindentation measurements indicated that the mechanical strength of BCB caps was due to prestressing in BCB because of its tensile stress on silicon substrates. The polymer-based air-gaps provide a monolithic, low-cost, IC-compatible MEMS packaging option. In the study of thermal stability of PPC, the thermal stability enhancement of PPC by Cu(I) ions was investigated to determine its mechanism. An increased thermal stability of PAG-containing PPC film was previously reported by our group (PAG was Rhodorsil-FABA, an iodonium-based PAG). XPS analysis done on the surface of PPC/PAG films prepared on Cu-sputtered substrates showed the presence of copper in Cu(I) oxidation state. The amount of copper obtained in the film was found to be similar to the amount of PAG (Rhodorsil-FABA). Cu(I) ion can be formed through oxidation of copper surface by dissolved oxygen in the PPC solution. The thermal stability of PPC/PAG films was studied for a number of iodonium and sulfonium-based PAGs. Every PAG/PPC film including iodonium-based PAGs showed thermal stability increase in the UV exposed cases. No thermal stability increase was observed using any sulfonium-based PAG. Based on these observations, a mechanism was postulated for the observed thermal stability increase. A complexation-type of interaction between the iodonium in the cation of the PAG and Cu(I) disturbs acid creation mechanism of PAG. In the absence of acid, the PPC decomposition is not catalyzed, so the thermal stability of PPC increases on Cu surfaces. Overall, the work presented in this dissertation endeavored to improve the chip-chip interconnection and MEMS packaging through metallization, processing and materials research. Ag-based catalysts can reduce cost, and non-roughening H2SO4 treatment can ensure fast and reliable signal propagation between chips through electroless copper layers on PWBs. MEMS packaging using polymer-based air-gaps can enable simpler packaging process and produce low-cost MEMS devices. Control of thermal decomposition temperature of PPC can allow a wider range of processes and applications.

Benzer Tezler

  1. Realization of micromachined-electromechanical devices for wireless communication applications

    Haberleşme sistemleri uygulamaları için mikroişlenmiş - elektromekanik aygıtların gerçeklenmesi

    EMRE HEVES

    Yüksek Lisans

    İngilizce

    İngilizce

    2006

    Elektrik ve Elektronik MühendisliğiSabancı Üniversitesi

    Elektrik ve Elektronik Mühendisliği Ana Bilim Dalı

    DOÇ. DR. YAŞAR GÜRBÜZ

  2. Değiştirilmiş kohonen ağı simülasyon programı

    A Simulation program for modified kohonen network

    ENDER TUNÇ EROĞLU

    Yüksek Lisans

    Türkçe

    Türkçe

    1993

    Elektrik ve Elektronik Mühendisliğiİstanbul Teknik Üniversitesi

    PROF.DR. UĞUR ÇİLİNGİROĞLU

  3. IEEE 1149.1 standardı kullanarak test edilebilir lojik devre tasarımı

    Testable lojik circit design by using IEEE 1149.1 standard

    A.BETÜL TUNCER

    Yüksek Lisans

    Türkçe

    Türkçe

    1992

    Elektrik ve Elektronik Mühendisliğiİstanbul Teknik Üniversitesi

    PROF. DR. AHMET DERVİŞOĞLU

  4. Implantable sub-cm wireless resonators for MRI: From circuit theory to medical imaging

    MRG için implant edilebilir kablosuz cm-altı çınlaçlar: Devre teorisinden tıbbi görüntülemeye

    SAYIM GÖKYAR

    Doktora

    İngilizce

    İngilizce

    2017

    Mühendislik Bilimleriİhsan Doğramacı Bilkent Üniversitesi

    Elektrik-Elektronik Mühendisliği Ana Bilim Dalı

    PROF. DR. HİLMİ VOLKAN DEMİR

  5. Design and fabrication of integrated inductors with polymer-ferromagnetic core

    Tasarım ve entegre imalat polimer ve ferromanyetik çekirdek ile indüktörleri

    MAMADY KEBE

    Yüksek Lisans

    İngilizce

    İngilizce

    2014

    Elektrik ve Elektronik MühendisliğiFatih Üniversitesi

    Elektrik-Elektronik Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. HÜSEYİN SAĞKOL