Üç farklı kompozit materyalin monomer salımına yapay yaşlandırmanın etkisinin yüksek performanslı sıvı kromatografi ile değerlendirilmesi
Evaluation with high performance liquid chromatography analysis of effect of artificial aging to monomer releasing from three different composites materials
- Tez No: 416079
- Danışmanlar: DOÇ. DR. ALP ERDİN KOYUTÜRK
- Tez Türü: Doktora
- Konular: Diş Hekimliği, Dentistry
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2014
- Dil: Türkçe
- Üniversite: Ondokuz Mayıs Üniversitesi
- Enstitü: Sağlık Bilimleri Enstitüsü
- Ana Bilim Dalı: Pedodonti Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 78
Özet
Amaç: Bu çalışmanın amacı, üç farklı kompozit materyalden salınım yapan artık monomer miktarına yapay yaşlandırmanın etkisini Yüksek Performanslı Likit Kromatografi tekniği (HPLC) ile ölçmektir. Materyal ve Metot: Araştırmada indirekt posterior kompozit, posterior kompozit ve mikrohibrit kompozit olmak üzere 3 farklı kompozit materyali kullanıldı. Her kompozit materyalinden 1cm çapında 3mm yüksekliğinde silindir şeklinde 60 örnek hazırlandı. İndirekt posterior kompozit materyaller üreticinin talimatına göre polimerize edildi. Ağız ortamında oluşabilen sıcaklık farklılıklarını taklit edebilmek amacıyla örneklere ısı döngüsü cihazı kullanılmıştır. Isı döngüsü işlemi sonrası HPLC cihazı ile artık monomer miktarı ölçüldü. İndirekt posterior kompozit materyalinde Bisphenol A ethoxtylate dimetachrylate (Bis-EMA) ve Urethane dimethacrylate (UDMA), posterior kompozit materyalinde Bis-EMA, mikrohibrit kompozit materyalinde Bis-EMA ve Triethylene glycol dimethacrylate (TEGDMA) incelendi. Bulgular: UDMA ve TEGDMA monomerleri salım miktarları ısı döngüsü düzeyleri açısından istatistiksel olarak incelendiğinde lineer bir artış gösterdiği saptandı (p
Özet (Çeviri)
Aim: The aim of this study, to measure effect of thermal cycling on amount of monomer releasing from three different composite materials by HPLC analyzing method. Material and Method: Three different composite materials, which are inlay composite, posterior composite and micro-hybrid composite were used. Sixty cylinder specimens which have dimensions approximately 1 cm wide (diameter) and 3 mm depth were prepared. Inlay composite material was polymerized according to manufacturers' instructions. Thermal cycling device was used with the aim of can be simulate thermal differences which occur in the mouth media. Monomer was analyzed with HPLC device after thermal cycling process. As monomer amount of Bisphenol A ethoxtylate dimetachrylate (Bis-EMA) and urethane dimethacrylate (UDMA) in inlay composite material, amount of Bis-EMA in posterior composite material, amount of Bis-EMA and triethyleneglycol dimethacrylate (TEGDMA) in micro-hybrid composite material were investigated. Results: In terms of monomer release of thermal cycles levels showed a linear increase in UDMA and TEGDMA (p
Benzer Tezler
- Yara ve yanık tedavisi için aktif karbon/polimer kompozitlerin geliştirilmesi
Başlık çevirisi yok
ASLI GÜNİZ ATAÇ
- Pedodontide kullanılan farklı restoratif materyallerin polimerizasyon derinliğinin karşılaştırılmalı olarak incelenmesi
Comparative study of polymerization depth of different restorative materials used in pedodontics
HABİP ERTAY ATALAR
Doktora
Türkçe
2011
Diş Hekimliğiİstanbul ÜniversitesiPedodonti Ana Bilim Dalı
PROF. DR. KORAY GENÇAY
PROF. DR. MEHMET SAYIP EROĞLU
- İletken ve monodispers poli (pirol/stiren) kompozit lateks sentezi ve karakterizasyonu
Synthesis and characterization on conductive and monodisperse polly (pyrrole/styrene) composite latex
DİDEM BİNGÖLLÜ
Yüksek Lisans
Türkçe
1997
Kimya MühendisliğiHacettepe ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
DOÇ. DR. EMİN ARCA
- Development of high-performance and chlorine-resistant thin-film composite membranes with zwitterionic surfaces for seawater desalination
Deniz suyu desalinasyonunda kullanılacak zwitteriyonik katkılı yüksek performanslı ve klor direncine sahip ince film kompozit membranların geliştirilmesi
JALAL AL DIN SHARABATİ
Doktora
İngilizce
2019
Çevre Mühendisliğiİstanbul Teknik ÜniversitesiÇevre Mühendisliği Ana Bilim Dalı
PROF. DR. İSMAİL KOYUNCU
- Çocuk diş hekimliğinde kullanılan restoratif materyallerin polimerizasyon sonrası salınan artık monomer miktarının ın vıtro olarak değerlendirilmesi
In vitro evaluation of the amount of residual monomer released after polymerization of restorative materials used in pediatric dentistry
AYBERK İMREN