Investigation of the surfaces of dealkalized and weathered float glass
Alkalisi giderilmiş, hava ve neme maruz kalmış düz camların yüzeylerinin incelenmesi
- Tez No: 447138
- Danışmanlar: YRD. DOÇ. DR. UFUK ŞENTÜRK, YRD. DOÇ. DR. HADI M. ZAREIE
- Tez Türü: Yüksek Lisans
- Konular: Seramik Mühendisliği, Ceramic Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2016
- Dil: İngilizce
- Üniversite: İzmir Yüksek Teknoloji Enstitüsü
- Enstitü: Mühendislik ve Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmada, float metodu ile üretilen düz camların nem ortamındaki korozyon davranışları ve SO2/SO3 gaz dealkalizasyonunun bu camlar üzerine etkileri incelenmiştir. Bu çalışma için camın sadece hava yüzeyi kullanılmıştır, camın kalay yüzeyinde bir inceleme yapılmamıştır ve genel olarak dealkalizasyon işlemi uygulanmış ve uygulanmamış olmak üzere iki farklı tip numune kullanılmıştır. Nemli ortamda cam yüzey değişimleri üzerine yüzey temizleme işlemlerinin ve dealkalizasyonun etkileri detaylı bir şekilde ele alınmıştır. Ayrıca yaşlandırma öncesi ve sonrası cam yüzey yapı ve topografya değişimleri incelenmiştir. Yüzey topografyası atomik kuvvet mikroskobu (AFM), yüzey yapısı ise attenuated total reflection-fourier transform infrared (ATR-FTIR) spektroskopi, specular reflectance infrared (SR-IR) spektroskopi ve micro-Raman spectroskopi teknikleri kullanılarak araştırılmıştır. Bu çalışma sonucunda, ATR-FTIR ve SR-IR analiz sonuçları yaşlandırma etkisi hakkında bilgi verirken micro-Raman analizleri bu çalışma için sonuç vermemiştir. ATR-FTIR ve SR-IR analizleri için hesaplanan penetrasyon derinliği yaşlanma sonucu cam yüzeyinde meydana gelen değişimden büyüktür. ATR-FTIR ve SR-IR sonuçları incelenirken buna dikkat edilmelidir. Bu çalışmada AFM analiz sonuçları göstermiştir ki etanol yüzeyde giderilmesi güç bir film oluşturmuştur ve bu sebeple yüzey temizliği için kimyasal sıvı olarak izopropil alkol kullanılmıştır. Ayrıca, AFM analiz sonuçları sülfür gazı uygulaması yapılan cam yüzeylerde yaklaşık 2 nm derinliğinde çatlaklar olduğunu göstermiştir. Bu çatlakların sülfürleme sonucu yüzeyde oluşan sodyum tuzlarının altında olduğu düşünülmektedir.
Özet (Çeviri)
In this study, the effects of surface dealkalization due to SO2 or SO3 gas treatment of commercial soda lime silica float glass on the weathering behavior was investigated. Only the air side of the glass was studied. The changes in the glass surface were analyzed for their topography and structure. The surface topography was studied using atomic force microscopy (AFM). The findings show the formation of micro-cracks on the surfaces of as-produced glass surfaces when treated with sulfur gas. The weathered surfaces show an increased roughness with increased weathering. The surface structure was investigated using attenuated total reflection-Fourier transform infrared (ATR-FTIR) spectroscopy, specular reflectance infrared (SR-IR) spectroscopy, and micro-Raman spectroscopy techniques The results of the studies, ATR-FTIR and SR-IR techniques provided a reasonable insight on the surface structural changes while micro-Raman spectroscopy failed to detects these differences. ATR-FTIR and SR-IR the overall comparison of the effects of peak position with and without sulfur gas treatment suggests a wide scatter within each group. This scatter implies that sulfur gas treatment does not have any statistically significant effects. Also, the change in peak positions are no clear evidence of a decreasing or increasing peak position as the weathering period is increased by weathering effect. Additionally, the calculated penetration depth is found to be ~0,6-1 μm for these techniques. Namely, the penetration depth greater than the surface modification was observed. The results showed was not significantly affected by the surface dealkalization and weathering reactions. The analysis of the surface topography using AFM technique showed the formation of micro-cracks like features on the surfaces of sulfur treated glasses. These features are thought to occur under the sodium sulfate salt residue that is formed during the high temperature dealkalization reactions on the surface. Results sample preparation, i.e. cleaning, was found to have a significant effect on the surface properties. A method has been developed to minimize the effects of sample preparation on the surface of the glass.
Benzer Tezler
- Investigation of surface forces on solid surfaces in the precence of crystalline and dissolved Tris-HCl using scanning probe microscopy techniques
Katı yüzeyler üzerindeki yüzey kuvvetlerinin kristal ve çözelti halindeki Tris-HCl varlığında taramalı uç mikroskopisi ile incelenmesi
ŞEYMA ŞÜKRAN NAYIR
Yüksek Lisans
İngilizce
2017
Fizik ve Fizik Mühendisliğiİstanbul Teknik ÜniversitesiFizik Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. ALEXANDR JONAS
- The investigation of surface topography for micro/nano scaled surfaces
Mikro/nano ölçekte topografik yüzey incelemesi
BİLGİNER GÜNDÜZ
Yüksek Lisans
İngilizce
2018
Makine MühendisliğiAydın Adnan Menderes ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. PINAR DEMİRCİOĞLU
- Investigation of behaviour of the electromagnetic waves in a parallel plate waveguide with grid type surfaces
Izgara tipi yüzeylerle bir paralel plaka dalga kılavuzunda elektromanyetik dalgaların davranışının incelenmesi
İSMAİL YILDIZ
Yüksek Lisans
İngilizce
2015
Elektrik ve Elektronik MühendisliğiÇukurova ÜniversitesiElektrik-Elektronik Mühendisliği Ana Bilim Dalı
PROF. DR. ABDULHAMİT SERBEST
- Investigation of graphene/hopg system and uhv system development for the study of germanium surfaces with atomic wires
Graphene/hopg sisteminin incelenmesi ve ge yüzeylerinin atomik teller ile çalışılması için uyv sistem geliştirilmesi
DİLEK YILDIZ
Yüksek Lisans
İngilizce
2014
Bilim ve Teknolojiİstanbul Teknik ÜniversitesiFizik Mühendisliği Ana Bilim Dalı
DOÇ. DR. OĞUZHAN GÜRLÜ
- Experimental and numerical investigation of the fretting fatigue of dissimilar mating surfaces
Farklı malzemelerin temas yüzeylerindeki titreşimli aşınma yorulmasının test ve nümerik olarak incelenmesi
YEZDAN MEDET KORKMAZ
Yüksek Lisans
İngilizce
2019
Havacılık ve Uzay MühendisliğiOrta Doğu Teknik ÜniversitesiHavacılık ve Uzay Mühendisliği Ana Bilim Dalı
DOÇ. DR. DEMİRKAN ÇÖKER