Geri Dön

CNC Torna tezgahında iş ve işlem yaprakları

Başlık çevirisi mevcut değil.

  1. Tez No: 46076
  2. Yazar: BABÜR ÖZÇELİK
  3. Danışmanlar: Y.DOÇ.DR. İSMAİL BİNİCİ
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 1995
  8. Dil: Türkçe
  9. Üniversite: Marmara Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 142

Özet

Özet yok.

Özet (Çeviri)

SUMMARY Todoy using CNC looms in occupation high schools and universities are diffused around Turkey. But there is no procedure or some thing else that teachers and students pursuit during their workshop studies. I searched, in the aim of helping to remove this deficiency.I based to programme DYNA 3000 H lathe looms that were bought for casting mold section EMCO lathe according to ISO system, according to the treaty of world Bank. I prepared my studyings in Gebze Occupation High School's CNC labrotory on DYNA 3000 H computers and checked all parts'. First part ; general information about CNC. Second part ; mecnings of terms about fragment programing CNC. Third part ; introduction of G functions. Before starting up machine or programmins the machine it's important to learn the parts and working introductions as much as possible. Also it's necessary to learn fragment dimensions, speed, power, chisel coposity and sensitivity. This introductions help to grow up reliable and profitable members. Fifth part ; explains the base concepts and other ambiguous automation forms, support to constitute CNC. In this unit the methods of how the machines understand the programmes a manipulated part and how the machines understand the programmes and how the control units make the climentions to the CNC machine, different kinds of systems there are messages or instructions are used which fell how to manipulate the parts writing CNC programmes are told. The good communication is a key for CNC security.Both the machine operator and the programmer have responsibility of security and must have very good communication.In the sevent part, the moin thing for security, planning carefulle and using the security in programming are talked about. Macking certain the machine to work safely and profitably, you hove to know these things which are talked about in the eight part how start and stop the machine, how to shunt by manuel, haw to make the calibration of the chisels. After the CNC contrails, htss of mehhods are improved for making easy to programme the computer and to make the using safer. One of these kinds of improve is having the control which asks questions for making the programmer to go for word the steps very speedy and correctly from the besinning and to the end.In the DYNA system these questions are named as“ sufle ”.These parts are explcined in the nineth period. In the tenth part ; how a programme for DYNA 3000 sery can be written, how to go to memory and how to process the parts by using the programme. In the eleventh part, ready cycles are told and mode known how to write a programme by showing some examples. In the twelveth part, the ready cycles and some exampled studyings are shown are about some exampled studyings are shown about some kinds of DYNA commands. In the 13 th part which is the aim of workking, there are the applies of the all topics. The programme studyings that are necessary for producing of different types of work parts, are mode both according to DYNA language and also according to the EMCO looms.While this has been doing, these ranks are followed ; l.The shape of the part that will be made up, 2.The choosing of cutting point, 3. The choosing of period number, the cutting and going for word speed, 4.The preparing of operation page, 5. To programme according to the DYNA language, 6. To programme according to the EMCO ( ISO system is based on ), Also at the end of this part, making similer studyings are made possible by giving example figures. At the end of the last part of the thesis, some kinds of the lathe looms are shown which are produced by the different firms. n

Benzer Tezler

  1. A feature based design software for parts to be machined in a four-axis CNC lathe

    Dört eksenli CNC torna tezgahında işlenebilecek parçalar için unsur tabanlı tasarım programı

    DEMİRALP HATİPOĞLU

    Yüksek Lisans

    İngilizce

    İngilizce

    2005

    Makine MühendisliğiOrta Doğu Teknik Üniversitesi

    Makine Mühendisliği Bölümü

    PROF.DR. SAHİR ARIKAN

  2. Yeni tip insert uç ile Al6061 malzemeye bilyeli material yöntemi uygulaması ve yüzey özelliklerinin incelenmesi

    Application of ball material method to Al6061 material with new type insert insert and its properties surface investigation

    FEYZA AYDIN

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Mühendislik BilimleriBatman Üniversitesi

    Malzeme Bilimi ve Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ OKTAY ADIYAMAN

  3. Kesici takımlara uygulanan kriyojenik işlemin ınconel 625 nikel esaslı süperalaşımın işlenebilirliğine etkisinin deneysel nümerik ve istatistiksel araştırılması

    Experimental numerical and statistical investigation of the effect of cryogenic treatment applied on cutting tools on machinability of inconel 625 nickel based superalloy

    MAHİR AKGÜN

    Doktora

    Türkçe

    Türkçe

    2021

    Makine MühendisliğiKarabük Üniversitesi

    İmalat Mühendisliği Ana Bilim Dalı

    PROF. DR. HALİL DEMİR

  4. AISI 4140 ıslah çeliğinin seramik kesici takımlarla tornalanmasında oluşan titreşimin yüzey pürüzlülüğüne etkisinin deneysel analizi

    Experimental analysis of the effect of vibration on the surface roughness in turning of AISI 4140 steel with ceramic cutting tools

    MUSA ŞEREMET

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiDüzce Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ MENDERES KAM

  5. CNC torna tezgahında 17?4 PH paslanmaz çeliğin işleme parametrelerinin deneysel olarak belirlenmesi

    Experimental determination of machining parameters of 17-4 PH stainless steel in CNC turning

    ALİ KALYON

    Yüksek Lisans

    Türkçe

    Türkçe

    2010

    Makine MühendisliğiMarmara Üniversitesi

    Makine Eğitimi Ana Bilim Dalı

    YRD. DOÇ. DR. MUSTAFA AY