Kil zeminlerde imal edilen baret kazıklarda grup etkileşimi üzerine bir inceleme
A study about group efficiency on barrette piles in clay soils
- Tez No: 504622
- Danışmanlar: DOÇ. DR. MUSTAFA TUĞRUL ÖZKAN
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2018
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Zemin Mekaniği ve Geoteknik Mühendisliği Bilim Dalı
- Sayfa Sayısı: 151
Özet
Günümüzde hızla artan şehirleşme ve gelişen teknoloji, zorlu zemin koşullarında da yapılar inşa edilmesi sonucunu beraberinde getirmiştir. Bu durumlarda başvurulan derin temel uygulamalarının en sık kullanılan türlerinden biri de kazıklı temellerdir. Kazıklı temeller, nadir istisnalar dışında çoğunlukla grup olarak değerlendirilmekte ve uygulanmaktadır. Literatürde bilhassa dairesel kesitli kazıklar ve bu kazıklarda grup etkileşimi ile ilgili her bir zemin tipi için yapılmış çok sayıda çalışma bulunmaktadır. Bunun yanında dikdörtgen kesitli bir kazık çeşidi olan baret kazıklar ve bu kazıklarda oluşan grup etkileşimi ile alakalı sınırlı sayıda çalışma bulunmaktadır. Bu çalışmanın amacı, baret kazıklarda grup yerleşimi için uzun ve kısa kazık kenarlarının katları olacak şekilde yeni bir kazık aralığı yaklaşımı tanımlamak ve getirilen bu yeni yaklaşım doğrultusunda kazık grubunda grup etkileşiminin hangi kazık aralığında sıfırlanıp ara kazık değerlerinde nasıl değiştiğini analiz etmektir. Bu doğrultuda yumuşak kil ve sert kilden oluşan iki tabakalı bir zemin profilinde bir kazık grubu modellenmiş; kısa kenar ve uzun kenar doğrultusunda değişen farklı kazık aralıklı modeller için taşıma kapasitesi ve grup etkileşim faktörü değerleri kaydedilmiştir. Yapılan analizlerde Plaxis 3D Foundation ver. 2.1 programı kullanılmıştır. Çalışmalar sonucunda kazık kısa kenar uzunluğunun (a=1,0m) 12 katı - kazık uzun kenar uzunluğunun (b=3,0m) 10 katı kazık aralıklarında kazık grubundaki kazık taşıma kapasiteleri, aynı koşullarda modellenmiş tekil kazık taşıma kapasitesi ile yaklaşık sonuç vermiştir. Kazık aralıkları daraltıldıkça kazıkların taşıma kapasitelerinde beklendiği üzere azalma gözlenmiştir. Ek bir sonuç olarak, uzun ya da kısa kenar doğrultusunda kazık aralığı değiştirmenin grup etkileşim faktörü değerine ne şekilde etki ettiği resmedilmiştir. Kısa kenar doğrultusunda kazık aralığını değiştirmenin, grup etkileşim faktörü üzerinde uzun kenar doğrultusunda kazık aralığını değiştirmekten daha etkili olduğu grafikler halinde sunulmuştur. Çalışmanın 2. bölümünde kazıkların sınıflandırılma şekilleri; 3. bölümünde düşey yük altındaki tekil kazıkların taşıma gücü ve oturması; 4. bölümünde ise grup kazıkların düşey yük altında taşıma gücü ve oturmalarının ne şekilde gerçekleştiği ele alınmıştır. Çalışmanın 5. bölümünde sonlu elemanlar yönteminin ve analizlerde kullanılan sonlu elemanlar tabanlı Plaxis 3D Foundation yazılımının özelliklerine değinilmiştir. Çalışmanın 6. bölümünde modelleme aşamaları, yazılım kullanılarak gerçekleştirilen analizler ve bu analizlerin derlemesi sunulmuştur. Çalışmanın son bölümünde ise, 6. bölümde elde edilen veriler ışığında varılan sonuç ve çalışmanın ne şekilde genişletilebileceğine dair önerilere yer verilmiştir.
Özet (Çeviri)
Rapidly growing urbanization and developing technology have brought the result of constructing structures under difficult ground conditions. One of the most frequently used types of deep foundation applications in these cases is pile foundations. In principle, the piles are structural elements that transfer the load from the superstructure to the soil. Apart from rare exceptions, pile foundations are mostly evaluated and applied as a group. In pile groups, an intersection occurs in the pile impact areas. Because of this intersection, the bearing capacities of the piles in the group will be different (usually less) than the bearing capacity of a single pile in the same conditions. It may be expected that settlement of a pile group will be different from settlement of a single pile in same conditions. There are numerous studies in the literature, especially for circular piles for each soil condition related to group efficiency of these piles. Al-Mhaidib (2007) finds that the group efficiency factor approaches 1 at 9 times of the pile diameter (9D) in the model experiments, that is, the group effect is close to zero. Prakash and Saran (1967) have shown that the group effect is not important when a gap of more than 6D is left between the piles (as mentioned in Toğrol and Tan, 2009). The purpose of this study is to define a new pile spacing approach which is multiple of long and short pile sides of the barrette piles and to analyze when the group interaction in the pile group is equal to zero and how it changes in the intermediate pile spacing values. In this direction, a pile group is modeled in a two layered soil profile consisting of soft clay and hard clay; bearing capacity and group efficiency factor values for different models with different pile spacings (varying in short edge and long edge directions) were recorded. Plaxis 3D Foundation ver. 2.1 software has been used in this study. With this study; A new pile spacing approach has been introduced for barrette piles which is multiple of long and short pile edges. In the direction of this new approach, in the group of piles modeled as 2x2 in clay soil, the spacing that the group interaction is equal to zero and the way it changes in the intermediate pile spacing values have been analyzed. Then, the load-displacement curves are plotted at the points determined at pile centers and the displacement value (19.54 cm) corresponding to 10% of the equivalent circular pile diameter has been accepted as the settlement limit. The load corresponding to this settlement limit has been determined as the pile bearing capacity based on analysis evaluations. In the classification of the analysis results at the first stage, a classification was made such that the pile spacing (B) in the long side b = 3.0 m direction was variable while the pile side was fixed at the short edge a = 1.0 m. Numerous trial analyzes have been conducted (on the largest pile group) to ensure that the pile group is minimally affected by the model boundary effects while model boundaries are defined with the need of keeping calculation times of the software at reasonable levels. Depending on all these limitations and requirements; model directions, 100x100 meters in the horizontal x and z directions and 60 meters in the vertical y direction, have been defined. Before going on with the calculation stage, points were chosen to provide curves for analysis purposes on the model. In order to obtain the load-displacement curves of the piles, the points corresponding to the pile center at the pile top were determined. Pile spacings used in short edge direction (A) are; 2.0a; 3.0a; 4.0a; 5.0a; 6,0a; 8.0a; 10.0a and 12.0a. Pile spacings used in the long edge direction (B) are; 2.0b; 3,0b; 4,0b; 5,0b; 6,0b; 8.0b and 10.0b. As a result of the studies, the pile bearing capacity value in the pile group at the pile spacing A = 12,0a - B = 10,0b (A = 12,0m - B = 30,0m) is close (almost the same) to the bearing capacity value of the single pile modeled under the same conditions. As the pile spacings were narrowed, a decrease in the bearing capacity of the piles has been seen as expected. In the analyzes made, the group efficiency factor values changed between 0.99 and 0.60. In the analyzes made on the pile spacing of A = 12,0a, the group efficiency factor was obtained between 0,99 and 0,83 as a result of pile spacing changes in the long side direction. In the analyzes made on A = 10,0a pile spacing, as a result of pile spacing changes in long edge direction, group efficiency factor is between 0.97 and 0.80; In the analyzes made on the pile spacing of A = 8,0a, as a result of the pile spacing changes in the long side direction, the group efficiency factor is between 0.95 and 0.77; In the analyzes made on the pile spacing of A = 6,0a, as a result of the pile spacing changes in the long side direction, the group efficiency factor is between 0,93 and 0,74; In the analyzes made on the pile spacing A = 5,0a, as a result of the pile spacing changes in the long edge direction, the group efficiency factor is between 0,91 and 0,71; In the analyzes made on A = 4,0a pile spacing, as a result of pile spacing changes in the long edge direction, the group efficiency factor is between 0,87 and 0,68; In the analyzes made on A = 3,0a pile spacing, as a result of pile spacing changes in the long edge direction, the group efficiency factor is between 0,82 and 0,65; In the analyzes made on A = 2,0a pile spacing as a result of pile spacing changes in the long edge direction, the group efficiency factor is varied between 0.75 and 0.60. The effect of pile spacing changes on the group efficiency factor has been categorized and evaluated in two ways:“short edge direction pile spacing A = constant”and“long edge direction pile spacing B = constant”. As an additional result, it is analysed whether changing the pile spacing in the long or short edge direction have more influences the group efficiency factor value and presented by using graphs. In the case, it is seen that the pile spacing changing in the short side direction where the long side direction pile spacing (B) is considered as fixed, has more effect on the change of group efficiency factor compared to the other situation. In other words, changing the pile spacing in the short edge direction is more effective than changing the pile spacing in the long edge direction on the group efficiency factor.
Benzer Tezler
- Basınç tipi zemin ankraj davranışının sayısal analizler ve saha deneyleri ile incelenmesi
Investigation of compression ground anchor behaviour through numerical analyses and field tests
GÖKALP DEMİRCİ
Yüksek Lisans
Türkçe
2024
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. RECEP İYİSAN
- Quality control of piles constructed in clayey soils with sonic integrity testing (SIT)
Killi zeminlerde inşa edilen kazıkların sonik süreklilik testi (SIT) yöntemi ile kalite kontrolü
FUAT ÖZBAŞ
Yüksek Lisans
İngilizce
2007
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
Y.DOÇ.DR. AYKUT ŞENOL
- Zemin ankrajlarının taşıma gücü ve imal yöntemlerinin taşıma gücüne etkisi
Soil anchor ultimate load capacity and construction methods effect on ultimate load capacity
ANIL HELVACIOĞLU
Yüksek Lisans
Türkçe
2015
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. AHMET OĞUZ TAN
- Yumuşak ve gevşek zeminlerin iyileştirilmesi: Yüksek basınçlı enjeksiyon kolonları ve taş kolonlar
Improvement of soft and loose soils: Jel grouting and stone columns
UMUT OSMANOĞLU
- Yüksek performanslı polipropilen fiber katkısının kil zeminin drenajsız kayma direncine etkisinin incelenmesi
Investigation of the effect of high performance polypropylene fiber additive on the undrained shear strength of clay soil
FATİH KÜÇÜK
Yüksek Lisans
Türkçe
2021
İnşaat MühendisliğiSakarya Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. SEDAT SERT