YSZ, Gd2Zr2O7 ve YSZ/Gd2Zr2O7 içerikli termal bariyer kaplama sistemlerinin izotermal oksidasyon ve termal çevrim davranışlarının incelenmesi
Investigation of isothermal oxidation and thermal cyclic behaviors of thermal barrier coating systems with YSZ, Gd2Zr2O7 and YSZ/Gd2Zr2O7 content
- Tez No: 520668
- Danışmanlar: PROF. DR. HAYRETTİN AHLATCI, DR. ÖĞR. ÜYESİ ABDULLAH CAHİT KARAOĞLANLI
- Tez Türü: Doktora
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2018
- Dil: Türkçe
- Üniversite: Karabük Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 234
Özet
Termal bariyer kaplama (TBC) sistemleri yaygın olarak gaz türbin bileşenlerinde ısıl izolasyon amacıyla kullanılmaktadır. TBC sistemlerinin özelliklerinin geliştirilmesi için birçok yöntem ve yeni malzeme geliştirilmektedir. Soğuk gaz dinamik sprey (CGDS), yoğun ve oksitsiz metalik kaplamaların üretimine olanak sağlayan, gelecek vaat eden bir kaplama tekniğidir. Elektron ışını ile fiziksel buhar biriktirme (EB-PVD) tekniği ise kolonsal yapılı TBC'lerin üretimine olanak sağlaması sebebiyle servis koşullarında yüksek performans sağlayan bir kaplama tekniğidir. Üst kaplamada geleneksel olarak kullanılan itriya ile stabilize edilmiş zirkonya (YSZ) artık hedeflenen servis koşulları için uygun olmadığından son yıllarda nadir toprak elementlerinin zirkonatları YSZ'ye alternatif olarak denenmektedir. Bu çalışmada, nikel esaslı süper alaşım Inconel 718 altlık malzeme üzerine, yüksek hız oksi yakıt (HVOF) ve CGDS teknikleri kullanılarak CoNiCrAlY içerikli tozlar püskürtülerek bağ kaplamaların üretimi gerçekleştirilmiştir. Bağ kaplamaların üzerine ise EB-PVD tekniği kullanılarak YSZ, Gd2Zr2O7 (GZ) ve YSZ/GZ üst kaplama malzemesi olarak biriktirilmiştir. Üretilen TBC'ler vakum ısıl işlemine tabi tutulduktan sonra, 1000 °C ve 1100 °C'lerde 8, 24, 50 ve 100 saat izotermal oksidasyon testlerine ve 1150 °C bekletme sıcaklığında fırın termal çevrim testlerine tabi tutulmuşlardır. Testlerin öncesinde ve sonrasında TBC'ler mikroyapısal olarak incelenmişlerdir. Oksidasyon ve termal çevrim testleri esnasında bağ kaplama ile üst kaplama arayüzeyinde oluşan termal olarak büyüyen oksit (TGO) tabakasının davranışı ve termal çevrim sonrası meydana gelen hasarlar birbirleriyle kıyaslanarak ve tartışılarak açıklamalar yapılmıştır.
Özet (Çeviri)
Thermal barrier coating (TBC) systems are widely used for thermal insulation in gas turbine components. A number of methods and new materials are being developed to improve the properties of TBC systems. Cold gas dynamic spray (CGDS) is a promising coating technique that allows the production of dense and non-oxidized metallic coatings. Electron beam physical vapor deposition (EB-PVD) technique is a coating technique that provides high performance in service conditions because it allows the production of columnar structured TBCs. Since Yttria-stabilized zirconia (YSZ), traditionally used in the top coat, is no longer suitable for targeted service conditions, in recent years zirconates of rare earths have been tested as an alternative to YSZ. In this study, the production of bond coatings was carried out on nickel-based superalloy Inconel 718 substrate material by spraying CoNiCrAlY-containing powders using high velocity oxy-fuel (HVOF) and CGDS techniques. YSZ, Gd2Zr2O7 (GZ) and YSZ/GZ top coating materials were deposited onto the bond coatings using EB-PVD technique. After being subjected to vacuum heat treatment, the produced TBCs were subjected to isothermal oxidation tests at 1000 ° C and 1100 ° C for 8, 24, 50 and 100 hours and to furnace thermal cycling tests at 1150 ° C dwell temperature. Before and after tests, TBCs were examined as microstructural. During the oxidation and thermal cycle tests, the behavior of the thermally grown oxide (TGO) layer at the interface between the bond and top coat and, the damages that occurred at the end of the thermal cycle tests was discussed comperatively with each other.
Benzer Tezler
- Farklı kompozisyonlara sahip termal bariyer kaplama (TBC) sistemlerinde oluşan sıcak korozyon ve cao-mgo-al2o3-sio2 (Cmas) etkisinin incelenmesi
Investigation of hot corrosion and cao-mgo-al2o3-sio2 (Cmas) effect on thermal barrier coating (TBC) systems with different compositions
YASİN ÖZGÜRLÜK
Doktora
Türkçe
2020
Metalurji MühendisliğiKarabük ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. HAYRETTİN AHLATCI
- Çok katmanlı ve fonksiyonel derecelendirilmiş CYSZ/Gd2Zr2O7 esaslı yeni nesil termal bariyer kaplamaların üretimi ve karakterizasyonu
Processing and characterization of multilayered and functionally graded CYSZ/Gd2Zr2O7 based new generation thermal barrier coatings
MUSTAFA GÜVEN GÖK
Doktora
Türkçe
2015
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. GÜLTEKİN GÖLLER
- Farklı ortam koşullarının termal bariyer kaplama özelliklerine etkisinin incelenmesi
Investigation of the effect of different ambient conditions on thermal barrier coating properties
SİNEM ŞAMİ
Yüksek Lisans
Türkçe
2022
Metalurji MühendisliğiYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ BURAK BİROL
- YSZ ve CSZ esaslı termal bariyer kaplamaların üretimi, karakterizasyonu ve termal çevrim performanslarının karşılaştırılması
Manufacturing, characterizaton of YSZ and CSZ based thermal barrier coatings and comparison of the thermal cycling performance
EKREM ALTUNCU
Doktora
Türkçe
2011
Metalurji MühendisliğiSakarya ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. FATİH ÜSTEL
- YSZ esaslı mühendislik seramiklerinin enjeksiyon döküm yöntemiyle üretim süreçlerinin incelenmesi
Processing steps of the YSZ based engineering ceramics produced by the injection casting method
ŞEBNEM YILMAZ