Otobüs direncini düşürmek için bir yöntem
A method for the reduction of bus drag
- Tez No: 623330
- Danışmanlar: DR. ÖĞR. ÜYESİ ERHAN FIRAT
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: Türkçe
- Üniversite: Munzur Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 52
Özet
Enerji tasarrufu, günümüzde insanoğlunun başlıca zorlu görevlerinden birisi olmuştur. Enerji tüketenler içerisinden, ulaşım, özellikle de kara ulaşımı, önemli bir kısmı temsil etmektedir. Akış kontrolü, direnci düşürerek yakıt tüketimini azaltmak için en iyi yoldur. Mevcut tezde, ince, otobüse göre akışa ters yönde yerleştirilen ince düz plakanın uygulanmaya başlamasıyla, yaklaşık olarak 1:25 ölçekli otobüs modellerinin direncini azaltan bir yöntem incelenmiştir. Araştırma, Munzur Üniversitesi'nin kapalı çevrim rüzgar tüneli içerisinde gerçekleştirilmiştir. Plaka uzunluğunun belirli bir aralığı (l), otobüs ile plaka arasındaki boşluğun belirli bir aralığı (g) ve Reynolds sayısının belirli bir aralığının temel aerodinamik etkileri, sapmanın olmadığı durum için değerlendirilmiştir. Otobüs modellerini ve plakaları inşa etmek için birleştirmeli yığma modelleme (BYM) teknolojisinden faydalanan bir üç-boyutlu yazıcı kullanılmıştır. Plakalar ve otobüs modelleri arasındaki akışın detayları, duman-tel akış görselleştirme tekniği kullanılarak elde edilmiştir. Tünel, tek-eksenli bir kuvvet ölçüm sistemi ile donatılmış ve bu sistem direncin doğrudan ölçümü için kullanılmıştır. Bu tezin temel amacı, tam ölçekli bir otobüs üzerine etkiyen direnç kuvvetini azaltabilmek için bu tarz dışa yerleştirilebilen parçaları kullanmanın uygulanabilirliğini kontrol etmektir. Otobüs modellerinin direnç katsayılarında maksimum düşüş elde edebilmek için, boyutsuz plaka uzunluğu l*=0,7 olan düz plakanın otobüsün g*=0,1 olacak şekilde ön tarafına yerleştirilmesi gerektiği tespit edilmiştir. Model-1 için, Re=200000'de, bu metot sadece Model-1'e etkiyen direncin %84,1'i kadarlık bir sistem direnci üretmiştir. Model-2 için, Re=200000'de, bu metot sadece Model-2'ye etkiyen direncin %98,9'u kadarlık bir sistem direnci üretmiştir.
Özet (Çeviri)
A method for the reduction of bus drag Saving energy has become one of the main challenges of human beings today. Among energy consumers, transportation represents a significant part, especially ground transportation. Flow control is the best way to reduce the fuel consumption by reducing drag. In the present thesis, a method of reducing the drag of an approximately 1:25 scale bus models by the introduction of thin upstream-placed flat plate was investigated. The investigation was carried out in the Munzur University's closed circuit wind tunnel. The basic aerodynamic effects of a range of plate lengths (l), a range of gaps between plate and bus (g), and a range of Reynolds numbers (Re) were assessed for 0° yaw. A three-dimensional printer that utilizes the fused deposition modeling (FDM) technology was used to construct the bus models and plates. Details of the flow between the bus models and plates were obtained using the smoke-wire flow visualization. The tunnel was equipped with an external one-component force balance and this was used for direct measurement of drag. The main purpose of this thesis is to check the feasibility of using such external devices for reducing drag on the full scale buses. It was found that to reach a maximum reduction of the drag coefficients of the bus models, flat plate with a dimensionless plate length of l*=0.7 must be placed g*=0.1 upstream of the buses. For Model-1, this method produces a system drag that is 84.1% that of the Model-1 alone, at Re=200000. However, for Model-1, this method produces a system drag that is 98.9% that of the Model-2 alone, at Re=200000.
Benzer Tezler
- Taşıt aerodinamik özelliklerinin sayısal yöntemlerle incelenmesi
Investigation of vehicle aerodynamics by numerical methods
MARKOS ÇAĞAN
- Yaşlandırılmış ve kaplama işlemi uygulanmış Cu-Cr-Zr alaşımının yapısal, mekanik ve tribolojik özelliklerinin incelenmesi
Investigation of structural, mechanical and tribological properties of aged and coated Cu-Cr-Zr alloy
ÖZGÜR YÜKSEL
Yüksek Lisans
Türkçe
2022
Makine MühendisliğiSamsun ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. İLHAN ÇELİK
- Computer simulation of rollover test of a category M3 vehicle superstructure using dynamic analysis software according to UNECE regulation no 66.02
UNECE R66.02 regülasyonuna göre dinamik analiz yazılımını kullanarak yapılan M3 kategori araç üst yapısının devrilme testinin bilgisayar simülasyonu
DENİZ GÖYDENİZ
Yüksek Lisans
Türkçe
2022
Otomotiv MühendisliğiÇukurova ÜniversitesiOtomotiv Mühendisliği Ana Bilim Dalı
DOÇ. DR. HASAN SERİN
- Yüksek fırın cürufu ve metakaolinin yarı rijit kaplamada katkı malzemesi olarak kullanılması
Improving the performance of filling mortar used in semi-rigid pavement with blast furnace slag and metakaolin
HASIB FAISAL HAFIZI
Yüksek Lisans
Türkçe
2023
İnşaat MühendisliğiAkdeniz Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. SEVİL KÖFTECİ
- Bitümlü kaplamaların termal davranışlarının performans testleri ile incelenmesi
Investigation of thermal behaviour of asphalt mixtures with performance tests
YÜKSEL TAŞDEMİR
Doktora
Türkçe
2003
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. EMİNE AĞAR