Geri Dön

Amonyak-su buharı akışkanlı bir absorpsiyonlu soğutma makinası bileşenlerinin ısıl tasarımı

Thermal design of components of an ammonia-water absorption chiller

  1. Tez No: 646947
  2. Yazar: UĞUR BÜYÜKTUNCER
  3. Danışmanlar: PROF. DR. MUSTAFA SERHAN KÜÇÜKA
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2020
  8. Dil: Türkçe
  9. Üniversite: Dokuz Eylül Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 74

Özet

Bu çalışmada Engineering Equation Solver programı kullanılarak amonyak – su akışkanlı ve tek etkili bir absorpsiyonlu soğutma çevriminin termodinamik analizi gerçekleştirilmiş ve çevrim elemanlarının ısıl yükleri hesaplanmıştır. Sistemde, yoğuşturucu (kondenser) ve buharlaştırıcı (evaporatör) arasında bir ön soğutucu ve absorber ve jeneratör arasında ise çözelti ön ısıtıcısı mevcuttur. Çalışmada buharlaştırıcı sıcaklığı -10 santigrat derece; absorber ve yoğuşturucu sıcaklığı 40 santigrat derece; çözelti ısı değiştirici etkinliği 0,8 ve ön soğutma ısı değiştiricisi etkinliği 0,5 kabul edilmiştir. Yapılan hesaplamalara göre jeneratörden çıkıp damıtma kolonunu terk eden buharın amonyak derişim oranı yüzde 97,25 olup, ayırıcıda (rectifier) yüzde 99,9 mertebesinde zenginleştirilmektedir. Isı değiştiricilerin etkinlik katsayılarının ve jeneratör sıcaklığının değişimlerinin soğutma etkinlik katsayısı ve soğutma kapasitesi üzerine etkileri grafiklerle gösterilmiştir. Çalışmada ayrıca yaklaşık 3 kilowatt soğutma kapasitesi için sistem bileşenlerinin ısıl yükleri ile ısı transfer yüzeyleri hesaplanmış ve ön tasarımları yapılmıştır. Buna göre jeneratör yükü 7,798 kilowatt ve ısı transfer yüzey alanı 0,65 metrekaredir. Jeneratör ve damıtma kolonu bütünleşik tasarlanmıştır. Damıtma kolonu tepsileri 0,05 metre çapındadır. Ayırıcıdan atılan ısı miktarı 0,864 kilowatt olup soğutucu boru demeti yüzey alanı 1,384 metrekare olarak hesaplanmıştır. Absorberde soğutma suyuna aktarılan ısı 7,579 kilowatt'tır. Kütle transferine de uygun olan yüzey alanı 1,64 metrekaredir.

Özet (Çeviri)

In this study, the thermodynamic analysis of a single stage ammonia - water absorption cooling cycle was performed by using Engineering Equation Solver and thermal loads of the cycle components were calculated. The system has a pre-cooler between the condenser and the evaporator and a solution preheater between the absorber and the generator. In the study, the evaporator temperature is -10 degrees Celsius; absorber and condenser temperature 40 degrees Celsius; solution heat exchanger effectiveness 0.8 and precooler heat exchanger effectiveness 0.5 assumed. According to the calculations, the ammonia concentration rate of the steam leaving the generator and leaving the distillation column is 97.25 percent, and it is enriched in the rectifier at the level of 99.9 percent. The effects of heat exchanger efficiency coefficients and generator temperature changes on the cooling efficiency coefficient and cooling capacity are shown graphically. In the study, the heat capacity of the system components and heat transfer surfaces were calculated and preliminary designs were made for the cooling capacity of approximately 3 kilowatts. Accordingly, the generator heat capacity is 7.798 kilowatt and the heat transfer surface area is 0.65 square meter. Generator and distillation column are designed integrated. The tray diameter of distillation column is 0.05 meter. The amount of heat removed from the rectifier is 0.864 kilowatt and the surface area of the coolant pipe bundle has been calculated as 1.384 square meter. The amount of heat transferred to the cooling water in the absorber is 7.579 kilowatt. The surface area, which is also suitable for mass transfer, is 1.64 square meter.

Benzer Tezler

  1. Habbecik pompalı absorbsiyonlu sistemlerin termodinamik analizi

    Thermodynamic analysis of diffusion absorption refrigeration systems

    YEŞİM BOYLU

    Yüksek Lisans

    Türkçe

    Türkçe

    2012

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. SEYHAN UYGUR ONBAŞIOĞLU

  2. Güneş enerjisi kaynaklı kombine ısıtma ve soğutma sistemi tasarımı ve prototip üretimi

    Design and analysis and prototyping of the combined heating and cooling system with the solar energy

    SADEEQ BAKR TAJULDEEN ALOMARI

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Makine MühendisliğiSüleyman Demirel Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. OSMAN İPEK

  3. Güneş enerjisinden faydalanarak absorpsiyon ile soğutma

    Başlık çevirisi yok

    NAZAN BİLGİN

    Yüksek Lisans

    Türkçe

    Türkçe

    1976

    Kimya MühendisliğiEge Üniversitesi

    PROF.DR. GÜRBÜZ ATAGÜNDÜZ

  4. Tek etkili absorbsiyonlu bir soğutma sisteminde ilave bir ısı değiştirici eklenmesinin etkileri: Termodinamik analiz

    In a single-acting absorption cooling systemeffects of adding additional heat exchanger:thermodynamic analysis

    TURGUT ŞAŞMAZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Makine MühendisliğiBaşkent Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. TAHİR YAVUZ