AlFe2B2 ince filmlerinin yapısal, manyetik ve elektronik özelliklerinin incelenmesi
Investigation of structural, magnetic and electronic properties of AlFe2B2 thin films
- Tez No: 734922
- Danışmanlar: PROF. DR. ŞİNASİ BARIŞ EMRE
- Tez Türü: Yüksek Lisans
- Konular: Fizik ve Fizik Mühendisliği, Physics and Physics Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2022
- Dil: Türkçe
- Üniversite: Ankara Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Fizik Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 81
Özet
Bu tez çalışmasında, AlFe2B2 metal borür alaşımı argon atmosferi altında ve oda sıcaklığında kompozisyonal hedef kullanılarak SiO alttaşlar üzerinde dc manyetik alanda sıçratma yöntemiyle üretilmiştir. Elde edilen ince filmlerin istenilen kompozisyonlarda üretildiğini tespit etmek için X-ışını spektrometresi kullanılmıştır. İnce filmlerin kristal yapısını öğrenebilmek amacıyla Cu Kα kaynaklı X-ışını kırınımmetresi kullanılmıştır. Manyetik özelliklerinin karakterize edebilmek amacıyla titreşimli örnek manyetometresi kullanılmıştır. Çıkan sonuçlara göre ince film üretiminde istenilen yapının elde edilebilmesinin güç ve basınç değerlerine doğrudan bağlantılı olduğu gözlemlenmiştir. Buna göre belirli bir güç ve basınç değerinde üretilen filmde AlFe2B2 fazına rastlanmışken, parametrelerde ufak değişiklikler yapıldığında AlFe2B2 fazına rastlanmayıp elementlerin sadece oksitli ara fazları görülmüştür. X-ışını fotoelektron spektrometre ölçümlerine göre sadece 1 nolu örnekte AlFe2B2 fazına rastlanmış olup 2 ve 3 nolu örneklerde AlFe2B2 fazına rastlanmamıştır. Bununla beraber oda sıcaklığında yapılan X-ışını kırınım deneylerine göre ise 3 örnek içinde elementlerin oksitli ara fazları gözlemlenmiştir. Titreşimli örnek manyetometresi ölçümlerine göre 1 nolu örndeği oda sıcaklıpı yakınlarında manyetik faz geçişi yaptığı, 2 ve 3 nolu örneklerde herhangi bir faz geçişi olmadığı gözlemlenmiştir.
Özet (Çeviri)
In this thesis, AlFe2B2 metal boride alloy was produced by dc magnetron sputtering on SiO substrates using a compositional target under argon atmosphere and at room temperature. X-ray spectrometer was used to determine that the obtained thin films were produced in the desired compositions. In order to learn the crystal structure of thin films, a Cu Kα sourced x-ray diffraction meter was used. A vibrating sample magnetometer was used to characterize its magnetic properties. According to the results, it was observed that obtaining the desired structure in thin film production is directly related to the power and pressure values. Accordingly, while the AlFe2B2 phase was found in the film produced at a certain power and pressure value, when minor changes were made in the parameters, the AlFe2B2 phase was not encountered and only the oxidized impurity phases of the elements were observed. According to X-ray photoelectron spectrometry measurements, AlFe2B2 phase was found only in sample 1, and AlFe2B2 phase was not found in samples 2 and 3. However, according to the X-ray diffraction experiments performed at room temperature, oxidized impurity phases of the elements were observed in 3 samples. According to the measurements of the vibrating sample magnetometer, it was observed that the sample 1 made a magnetic phase transition near the room temperature, and there was no phase transition in the samples 2 and 3.
Benzer Tezler
- AlFe2B2 MAB fazında krom (Cr) ve vanadyum (V) ikamelerinin malzeme özellikleri üzerindeki etkileri: Deneysel destekli modelleme çalışması
The effects of chromium (Cr) and vanadium (V) substitutions on the material properties of AlFe2B2 MAB phase: An experimentally supported modelling study
AHMET SEFA ATALAY
Doktora
Türkçe
2024
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. CEVAT BORA DERİN
- SHS yöntemi ile tufal kullanılarak AlFe2B2 intermetalik bileşiğinin üretimi
Production of AlFe2B2 intermetallic compound by using mill scale with SHS method
ECEM TURHAN
Yüksek Lisans
Türkçe
2019
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DOÇ. DR. CEVAT BORA DERİN