Geri Dön

Seçici geçirgen nano tekstil yapılarda alternatif yöntemlerin incelenmesi

The investigation of alternative methods in selective permeable nano textile structures

  1. Tez No: 805449
  2. Yazar: ÇETİN AKA
  3. Danışmanlar: PROF. DR. AYSUN AKŞİT
  4. Tez Türü: Doktora
  5. Konular: Tekstil ve Tekstil Mühendisliği, Textile and Textile Engineering
  6. Anahtar Kelimeler: Tek iğneli, santrifüj, elektro lif çekimi, görüntü işleme, jet, Single-needle, centrifugal, electrospinning, image processing, jet
  7. Yıl: 2023
  8. Dil: Türkçe
  9. Üniversite: Dokuz Eylül Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Tekstil Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Tekstil Mühendisliği Bilim Dalı
  13. Sayfa Sayısı: 290

Özet

Elektro lif çekimi mikron altı çapta filament üretme tekniğidir. Basit tek iğneli sistemlerle küçük çaplı nanolifli dokusuz yüzeyler üretilebilmesine rağmen, bu yüzeyler ticarileştirilememiştir. Bu çalışmada, nanolifli yüzeylerin yığın halde üretilebilmesi için yeni bir elektro lif çekim sistemi alternatif bir yöntem olarak geliştirilmiştir. Bu tezin amacı, atık ve bol miktarda bulunan poliesterin yüksek katma değerli nanolifli dokusuz yüzeylere dönüştürülmesi için alternatif olanaklarının araştırılmasıdır. Bu amaç çerçevesinde, tek iğneli ve santrifüj elektro lif çekim sistemler kullanılarak nanolifli dokusuz yüzeyler üretilmiş ve oluşan liflerin özellikleri karşılaştırılmıştır. Bu tez çalışmasında poliester polimerlerine ait molekül ağırlığı kinematik viskozimetri yöntemiyle tespit edilmiş ve lif özelliklerine etkisi araştırılmıştır. Tek iğneli sistemde lif çekim sırasında oluşan elektriksel jetin ve oluşan liflerin morfolojik yapısı görüntü işleme yöntemiyle karakterize edilmiştir. İğneli sistemle üretilen liflerin çekim oranları hesaplanmıştır. Diğer yandan, alternatif ve yenilikçi bir santrifüj elektro lif çekim prototipi geliştirilmiş ve lif çekimi gerçekleştirilmiştir. Tek iğneli elektro lif çekim sisteminde nanolifli dokusuz yüzeylerin üretilmesinde konsantrasyondaki artışın uzun jetlerin ve ardından daha kalın çaplı liflerin oluşumuna neden olduğu belirlenmiştir. Molekül ağırlığın ve konsantrasyonun lif morfolojisine önemli ölçüde etki ettiği bulunmuştur. Çözücüdeki TFA oranının lif özelliklerini önemli derecede değiştirdiği saptanmıştır. Atık PET şişeden hem tek iğneli hem de santrifüj elektro lif çekimi sistemiyle 500 nm altında düzgün filament nanolifli yüzeylerin çekilebildiği bulunmuştur. Santrifüj elektro lif çekim sistemi ile tek iğneli sistemle aynı çapta boncuksuz lifler çok daha kısa sürede çekilebilmektedir.

Özet (Çeviri)

Electrospinning is a technique of producing filaments in submicron diameter. Ultra-fine diameter fibre nonwovens haven't been commercialized, although they can produce with simple single-needle assemblies. In this study, a new electrospinning system has been developed as an alternative method to produce high-throughput nanofiber mat. The aim of thesis is to investigate alternative possibilities of converting waste and abundant polyester to high value-added nanofiber nonwovens. For this purpose, nanofiber nonwoven mats were produced using single-needle and centrifugal electrospinning systems and the properties of the spun fibres were compared. In this thesis, the molecular weight of polyester was determined by kinematic viscometer method and its effect on fibre properties was investigated. The morphological structure of the electrical jet and the fibres formed during spinning were characterized by image processing. Draw ratios of the single-needle fibres were calculated. On the other hand, an alternative and innovative centrifugal electrospinning prototype was developed and fibre spun. It was determined that the increase in concentration in the single-needle electrospinning system resulted in the formation of long jets and then coarser diameter fibres. It was found that molecular weight and concentration significantly affect fibre morphology. It was determined that the Trifluoracetic acid ratio in the solvent significantly changed the fibre properties. It has been found that smooth filament nanofiber surfaces can be spun from the waste polyester bottle under 500 nm with both systems. With the centrifugal electrospinning system, bead-free fibres of the same diameter can be spun in shorter time than the single-needle system.

Benzer Tezler

  1. İnce film kaplama yapılmış nanofiber membranların partikül filtrasyon performanslarının belirlenmesi

    Determination of particul filtration performances of thin film composite nanofiber membranes

    MÜGE BİÇER

    Yüksek Lisans

    Türkçe

    Türkçe

    2016

    Çevre Mühendisliğiİstanbul Teknik Üniversitesi

    Çevre Mühendisliği Ana Bilim Dalı

    PROF. DR. İSMAİL KOYUNCU

  2. Karbon dioksit ayırma amaçlı ince film kompozit/nanokompozit membranların hazırlanması

    Preparation of thin film composite/nanocomposite membranes for carbon dioxide separation

    GÜLEN BÜYÜKOLCA

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Kimya Mühendisliğiİstanbul Teknik Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. ŞERİFE BİRGÜL ERSOLMAZ

  3. Elektriksel olarak iletken, optik olarak geçirgen yapı tasarımı

    Electrically conductive, optically transparent structure design

    İLKER GÜNAY

    Doktora

    Türkçe

    Türkçe

    2022

    Elektrik ve Elektronik MühendisliğiAnkara Üniversitesi

    Elektrik ve Elektronik Mühendisliği Ana Bilim Dalı

    PROF. DR. ASIM EGEMEN YILMAZ

  4. Preparation of gold decorated cobalt-silica core-shell nanoparticles for surface enhanced raman scattering applications

    Yüzeyde güçlendirilmiş raman saçılması uygulamaları için altınla bezenmiş kobalt-silika çekirdek-kabuk nanoparçacıkların hazırlanması

    LÜTFİYE SEZEN KESER

    Yüksek Lisans

    İngilizce

    İngilizce

    2010

    KimyaOrta Doğu Teknik Üniversitesi

    Kimya Bölümü

    PROF. DR. MÜRVET VOLKAN

  5. Fabrication of thin film nanocomposite pressure retarded osmosis (PRO) membranes using cellulose nanocrystal (CNC) and evaluation of performances in the processes

    Selüloz nanokristal kullanılarak ince film nanokompozit basınç geciktirmeli osmoz (BGO) membranlarının üretimi ve proseslerde performans testlerinin gerçekleştirilmesi

    MEHMET EMİN PAŞAOĞLU

    Doktora

    İngilizce

    İngilizce

    2021

    Çevre Mühendisliğiİstanbul Teknik Üniversitesi

    Çevre Mühendisliği Ana Bilim Dalı

    PROF. DR. İSMAİL KOYUNCU