Geri Dön

Havacılık uygulamalarında kullanılan farklı otoklav dışı vakum infüzyon tekniklerinin incelenmesi ve inovatif alternatif bir infüzyon modelinin geliştirilmesi: Dinamik infüzyon prosesi (DIP)

Examination of various out of autoclave vacuum infusion techniques used in aviation applications and development of an innovative alternative infusion model: Dynamic infusion process (DIP)

  1. Tez No: 864338
  2. Yazar: İLHAN KAHRAMAN
  3. Danışmanlar: PROF. DR. ABDULLAH TUĞRUL SEYHAN
  4. Tez Türü: Doktora
  5. Konular: Mühendislik Bilimleri, Engineering Sciences
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2024
  8. Dil: Türkçe
  9. Üniversite: Eskişehir Teknik Üniversitesi
  10. Enstitü: Lisansüstü Eğitim Enstitüsü
  11. Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 168

Özet

Havacılık, uzay ve savunma sanayilerinde sürekli fiber takviyeli ileri kompozit malzemelerin geleneksel mühendislik malzemelerin yerine kullanımı gün geçtikçe artmaktadır. Bunun nedeni, ileri kompozit malzemelerin, özgül dayanç ve özgül rijitlik (stiffness) gibi özelliklerinin geleneksel mühendislik malzemelerine kıyasla daha üstün olmasıdır. Yukarıda bahsedilen bu sektörler için üretilen polimer matrisli kompozit malzemelerin üretiminde en yaygın kullanılan yöntem otoklav ile kompozit üretimidir. Öte yandan, otoklavların ilk yatırım ve işletme maliyetleri diğer ileri kompozit malzeme üretim yöntemlerine göre oldukça fazladır. Otoklav süreci kesikli (batch) bir süreç olduğundan, otoklav boyutu arttıkça parça yükleme ve boşaltma döngüleri üretim hızında dar boğaza neden olmaktadır. Bu nedenle, literatürde Otoklav Dışı (Out of Autoclave) üretim yöntemlerinin geliştirilmesi üzerine yapılan çalışmalar son yıllarda ivme kazanmıştır. Bu doktora tezi çalışması kapsamında, CAPRI ve SCRIMP gibi kendini kanıtlamış yöntemlere bir alternatif olabileceği öngörülen Vakum İnfüzyon Tekniğinin bir türevi Dinamik İnfüzyon Prosesi (DIP) karbon fiber takviyeli kompozitlerin üretimi için önerilmiştir. Ayrıca polimer esaslı karbon fiberlerin fiber hacim oranının hesaplanmasında TGA kullanımını esas alan yeni bir yöntem geliştirilmiş ve literatürde çok kullanılan optik esaslı ve yaş kimya asit sindirme analizine dayalı metotların kullanımı ile elde edilen veriler ile karşılaştırılmıştır. Sonuç olarak önerilen bu tekniğin hem hassasiyet hem de analiz süresi açısından diğer tekniklerden daha iyi olduğu deneysel olarak ispatlanmıştır. Sonrasında üretim tekniklerinin kompozitlerin nihai mekanik özelliklerine etkisi 3 nokta eğme testi esas alınarak irdelenmiştir. Bu tez kapsamında geliştirilen kullanılması önerilen DIP tekniğinin bu tez kapsamında yapılan teorik ve deneysel çalışmalar ışığında özgün bir yaklaşım olduğunu ve parça geometrisinin kompleksliğinden bağımsız olarak havacılık uygulamalarında kullanılabilecek kalitede kompozit parçalar üretme potansiyeline sahip olduğu sonucuna varılmıştır.

Özet (Çeviri)

The use of continuous fiber-reinforced advanced composite materials (FRPCs) instead of traditional engineering materials has been gradually increasing in the aviation, space, and defense industries, since the properties of advanced composite materials, such as specific strength and specific stiffness, are superior to those of traditional engineering materials. The most widely used method in the production of FRPCs for these sectors mentioned above is autoclave composite production. On the other hand, the initial investment and operating costs of autoclaves are quite high compared to other advanced composite material production methods. Since the autoclave process is a batch process, as the autoclave size increases, part loading and unloading cycles cause a bottleneck in the production rate. Manufacturers are determined to overcome the drawbacks of the use of autoclaves due to these handicaps. It is for this reason that studies in literature performed on the development of out-of-autoclave production methods have gained massive attraction in recent years. In the framework of this PhD study, the Dynamic Infusion Process (DIP), an innovative and brand-new derivation of the Vacuum Infusion Process that is deemed to be an alternative to proven methods such as CAPRI and SCRIMP, has been proposed to produce carbon fiber-reinforced composites. Moreover, this study proposes a new method based on the use of TGA in calculating the fiber volume fraction of FRCPs that was developed and compared with the data obtained by using optical-based and wet-chemistry acid digestion analysis-based methods, which are widely used in the literature. The proposed method proves to be highly promising and even better than other techniques in terms of both measurement accuracy and analysis time. The effect of production techniques on the final mechanical properties of the composites was evaluated and discussed based on the 3-point bending test findings. It has been concluded that the recommended DIP technique is a promising approach considering the theoretical and experimental studies performed in this thesis, thus having the potential to produce quality FRPCs that can be employed in aviation applications regardless of the complexity of the part geometry.

Benzer Tezler

  1. A new production methodology for vacuum infusion process of advanced composite structures

    İleri kompozit yapılarda vakumlu infüzyon süreci için yeni bir üretim metodolojisi

    MOHSEN POORZEINOLABEDIN

    Doktora

    İngilizce

    İngilizce

    2017

    Makine MühendisliğiOrta Doğu Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. KEMAL LEVEND PARNAS

  2. Development of brazing process in ceramic matrix composites for in-space applications

    Uzay uygulamalarında kullanılan seramik matrisli kompozitlerin sert lehimleme proseslerinin geliştirilmesi

    EBRAR ÖZBEK EKİZ

    Yüksek Lisans

    İngilizce

    İngilizce

    2023

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. ÖMER SERDAR ÖZGEN

  3. Material properties of thermoplastic matrix carbon fiber reinforced high performance composites using automated fiber placement

    Termoplastik bazlı karbon fiber ile güçlendirilmiş ve otomatik fiber yerleştirme ile serilmiş kompozit malzemelerin malzeme özelliklerinin incelenmesi

    HATİCE AKÇAKAYA

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Mühendislik Bilimleriİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    DOÇ. MOHAMMADREZA NOFAR

  4. Askeri havacılık uygulamaları için yüksek güç yoğunluklu DA/DA yarım köprü tip çevirici tasarımı

    Design of high power density half bridge DC/DCconverter for military aerospace applications

    MEHMET HIDIR EL

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    Elektrik ve Elektronik MühendisliğiHacettepe Üniversitesi

    Elektrik-Elektronik Mühendisliği Ana Bilim Dalı

    DOÇ. DR. UMUT SEZEN

  5. Askeri havacılık uygulamaları için MIL STD 461E ve MIL STD 704E standartlarına uygun AA/DA çevirgeç koruma ve filtre sistemleri geliştirilmesi

    Implementation of AC/DC converter protection and filter systems for military aerospace applications according to MIL STD 461E and MIL STD 704E standards

    FATİH CANDAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2015

    Elektrik ve Elektronik MühendisliğiHacettepe Üniversitesi

    Elektrik-Elektronik Mühendisliği Ana Bilim Dalı

    DOÇ. DR. UMUT SEZEN