Al6061 matrisli sic ain ve oltu taşı takviyeli hibrit kompozitlerin toz metalurjisi ile üretimi ve fiziksel ve termal özelliklerinin incelenmesi
Production of Al6061 matrix sic ain and oltu stone reinforced hybrid composites with powder metallurgy and investigation of their physical and thermal properties
- Tez No: 884605
- Danışmanlar: DR. ÖĞR. ÜYESİ SERKAN ATEŞ
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2024
- Dil: Türkçe
- Üniversite: Burdur Mehmet Akif Ersoy Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 89
Özet
Bu tez çalışmasında Al6061 matrisli, SiC, AlN ve kolayca bulunabilen Oltu Taşı atıklarından elde edilen tozlar takviye elemanı olarak kullanarak çevre dostu ve uygun maliyetli hibrit kompozitler toz metalurjisi yöntemi ile üretildi. Oltu taşında madenden çıkarılıp nihai ürüne dönüşene kadar yaklaşık olarak %90 oranında atık meydana gelir. Söz konusu atıkların bertaraf edilmesinin hem çevresel etkileri hem de maliyeti göz önüne alındığında yeniden kullanımına yönelik metal matrisli kompozit üretiminde takviye malzemesi olarak kullanılabilirliği bu tez çalışmasının odağını oluşturmuştur. Bunun yanı sıra atık Oltu Taşı tozunun geleneksel takviye elemanlarından SiC ve AlN ile uyumu araştırıldı. Erzurum ilinin Oltu ilçesinde bulunan taş işlemeciliği alanında faaliyet gösteren atölyelerden atık olarak temin edilen Oltu Taşları bilyalı değirmende toz haline getirilip, piyasadan temin edilen SiC ve AlN tozları ile birlikte sarsma cihazında eleklerden geçirildi. 75µm elekten geçen ve 63µm elekten geçmeyen tozlar toplanılarak takviye elemanı olarak kullanıldı. Hassas terazide deney tasarımına uygun olarak tartılarak hazırlanan tozlar, 10dk süre ve 250dev/dk sabit hızda mekanik olarak karıştırılarak numunelere ait tozlar hazırlandı. 2 farklı ölçü ve biçimde tasarlanıp imal ettirilen pres kalıplarına yerleştirilen tozlar hidrolik preste 450MPa basınçta 1dk süre ile basıldı. Ardından 660ºC sıcaklıkta 360dk sürede sinterleme işlemine tabi tutularak kompozitler üretildi. Üretilen kompozitlerin mikro yapıları taramalı elektron mikroskobu ile görüntülenerek takviyelerin varlığı ve homojen dağılımları tespit edildi. Kompozitlerin sertlikleri Mikro Vickers sertlik ölçüm yöntemi, aşınma miktarları Pin-On disk yöntemi ve ısıl iletkenlikleri ise Laser Flash tekniği kullanılarak belirlendi. Kompozit içerisinde Oltu taşı tozunun artması ile kompozitin sertlik ve ısıl iletkenliğinin artarken, aşınma miktarının azaldığı belirlendi.
Özet (Çeviri)
In this thesis study, environmentally friendly and cost-effective hybrid composites with Al6061 matrix, SiC, AlN and powders obtained from easily available Oltu Stone waste were produced by the powder metallurgy method, using powders obtained from Oltu Stone waste as reinforcement elements. Approximately 90% of the waste is generated in Oltu stone until it is extracted from the mine and turned into the final product. Considering both the environmental effects and the cost of disposing of the waste in question, its usability as a reinforcement material in the production of metal matrix composites for reuse has been the focus of this thesis study. In addition, the compatibility of waste Oltu Stone powder with SiC and AlN, which are traditional reinforcement elements, was investigated. Oltu Stones, which were obtained as waste from workshops operating in the field of stone processing in Oltu district of Erzurum province, were pulverized in the ball mill and sieved in the shaking device together with SiC and AlN powders obtained from the market. The powders that passed through the 75µm sieve and did not pass through the 63µm sieve were collected and used as reinforcement elements. The powders of the samples were prepared by weighing them on a precision balance in accordance with the experimental design, and mechanically mixing them for 10 minutes and at a constant speed of 250 rpm. The powders placed in press molds designed and manufactured in 2 different sizes and shapes were pressed in a hydraulic press at 450MPa pressure for 1 minute. Then, composites were produced by sintering at 660ºC for 360 minutes. The microstructures of the produced composites were imaged with a scanning electron microscope and the presence of reinforcements and their homogeneous distribution were determined. The hardness of the composites was determined using the Micro Vickers hardness measurement method, the wear amount was determined using the Pin-On disk method and the thermal conductivity was determined using the Laser Flash technique. It was determined that as the Oltu stone powder increased in the composite, the hardness and thermal conductivity of the composite increased, while the amount of wear decreased.
Benzer Tezler
- Al 6061 matrisli SiC, Al2O3 ve yüksek fırın curufu takviyeli hibrit kompozitlerin yorulma davranışlarının incelenmesi
Investigation of tribological behavior of traditional and waste reinforced Al6061 metal matrix composites
AHMET ŞANLI
Yüksek Lisans
Türkçe
2017
Makine MühendisliğiBartın ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. SERKAN ATEŞ
- Polimer - metal matrisli kompozitlerden oluşturulmuş sandviç yapıların balistik davranışları
Ballistic behavior of sandwich structures constructed from polymer-metal matrix composites
ERTAN KÖSEDAĞ
Doktora
Türkçe
2020
Makine MühendisliğiErciyes ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. RECEP EKİCİ
- Al 6061 matrisli geleneksel ve atık takviyeli hibrit kompozitlerin tribolojik davranışlarının incelenmesi
Investigation of tribological behavior of traditional and waste reinforced Al 6061 metal matrix composites
ONUR KAMBER
Yüksek Lisans
Türkçe
2017
Makine MühendisliğiBartın ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. SERKAN ATEŞ
- Geleneksel ve atık takviyeli metal matrisli kompozitlerin yorulma davranışının incelenmesi
Investigation of fatigue behaviors of traditional and waste reinforced metal matrix composites
HASAN TOPRAK
Yüksek Lisans
Türkçe
2017
Makine MühendisliğiBartın ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. SERKAN ATEŞ
- AA 6061 matrisli SiC takviyeli kompozitlerin vakum infiltrasyon yöntemiyle üretiminde mekanik titreşimin infiltrasyon davranışı üzerinde etkisi
Investigation of the effect of vibration in the production of SiC reinforced AA 6061 matrix composite materials by vacuum infiltration method
MURAT ARI
Yüksek Lisans
Türkçe
2023
Savunma ve Savunma TeknolojileriKırıkkale ÜniversitesiSavunma Teknolojileri Ana Bilim Dalı
PROF. DR. RECEP ÇALIN