Atmosfer etkisinde kalan metallerin korozyonu
Corrosion of metals under the influence of the atmosphere
- Tez No: 966
- Danışmanlar: DOÇ. DR. HAYRİ YALÇIN
- Tez Türü: Yüksek Lisans
- Konular: Kimya Mühendisliği, Chemical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1987
- Dil: Türkçe
- Üniversite: Gazi Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Kimya Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 101
Özet
.IV- ATTOSFER ETKİSİNDE KALAN METALLERİN KOROZYONU ÖZET Ümit, ÖZDÎLER, M. S, GAZÎ ÜNİVERSİTESİ FEN BİLİMLERİ ENSTİTÜSÜ, 1987 Bu çalışmada atmosfer etkisinde kalan metallerin korozyon hızlarını saptamak için yapılan çalışmalar iki farklı deneyle sürdürülmüştür. Birinci deneyde, 10 cm x 15 cm boyutlarındaki ve 0.1 cm kalınlığındaki % 99.9 saflıktaki ticari çinko nu muneler 19 85 Haziranından itibaren yatayla 30 derecelik bir eğimle atmosfere bırakılmıştır. Numuneler 1,2,3,6 ve 9 aylık sürelerin sonunda alınarak ağırlık kayıpları hesaplanmıştır. Ağırlık kaybı verileri, korozyon ürünle rinin, numune yüzeyinden kimyasal yöntemlerle giderilme sinden sonra elde edilmiştir. İkinci deney, 1 mm çapında alüminyum tel kullanı larak yapılmıştır. Korozyon hızını arttırmak üzere alü minyum tel, bakır boru üzerine sıkıca sarılmış böylece bakır/alüminyum metallerinin galvanik etkisinden yarar lanılmıştır. Deney numuneleri üç ay süreyle, önceki deney ile aynı zaman ve yerde atmosfere bırakılmışlardır.-V Her iki deney sonunda hesaplanan korozyon hızları, numunede meydana gelen ağırlık azalması ölçülerek gram cinsinden bulunmuş ve um/yıl olarak ifade edilmiştir. Çinkonun korozyon hızını belirlemek için yapılan de ney sonuçları, literatürde Y = K (RH - RHo)Cso şeklinde belirtilen ve atmosferik korozyon hızı ile at mosferin taşıdığı kükürt dioksit konsantrasyonu ve rela- tif nem arasındaki ilişkiyi ifade eden bağıntı ile karşılaş t irilmiş tır.
Özet (Çeviri)
-VI- CORROSION OF FjETALS UNDER THE INFLUENCE OF THE ATMOSPHERE ABSTRACT Ümit ÖZDÎLER, M. S, Institute of Science and Technology of - Gazi University 1987 In this study, the corrosion tests, to determine the corrosion rates of metals, under the influence of atmosphere were carried out in two different tests. In the first test, 10 x 15 x 0,1 cm specimens of a special high-grade commercial zinc (99.9 %) had been exposed to the atmosphere since June, 19 85 at an angle of 30 degrees to the horizontal. The specimens were removed after exposure periods of 1,2,3,6 and 9 months and their weight losses were calculated. Weight-loss data -dere obtained after corrosion products have been removed chemicaly fron the surface of the specimens The second test was carried out by using pure aluminum wire of 1 mm diameter. In order to accelerate the corrosion rate, aluminum wire was wounded tightly around the copper bolt and by this way the galvanic effect between the metals of aluminum and copper was utilized. The specimens had been, exposed for 3 months at the same time and at the same place öf the- VII - fist test. At the end of the two tests, corrosion rates were found by calculating weight-loss as grams and were expressed asum/yr. The results of the experiments have been compared with the correlation given in the literature as; Y = K (RH - RHo)CS0 expressing the relation between atmospheric corrosion rate, concentration of sulfur dioxide in the atmosp here and relative humudity.
Benzer Tezler
- Titanyum alaşımlarının ısıl işlem ve mekanik özellikleri
Heat treatments and mechanical properties of titanium alloys
ALPTEKİN İŞLER
- Adana (Merkez) yol tozlarında ve yol kenarındaki topraklarda ağır metal kirliliği
The Heavy metal contamination in roadside dusts and soils in Adana (center)
NESLİHAN YETİKER
Yüksek Lisans
Türkçe
1998
Jeoloji MühendisliğiÇukurova ÜniversitesiJeoloji Mühendisliği Ana Bilim Dalı
PROF. DR. SERVET YAMAN
- Fosfojips atığının çevresel etkilerinin değerlendirilmesi
An assesment of the environmental impacts of phosphogypsum waste
GÜLER DARTAN
Doktora
Türkçe
2013
Çevre Mühendisliğiİstanbul Teknik ÜniversitesiÇevre Mühendisliği Ana Bilim Dalı
PROF. DR. İSMAİL TORÖZ
- B4C esaslı kompozitlerin B4C/Me başlangıç tozlarından hareketle spark plazma sinterleme (SPS) yöntemi ile üretilmesi ve karakterizasyonu
Production and characterization of B4C based composites from B4C/Me starting powders by using spark plasma sintering (SPS) method
MERAL CENGİZ
Doktora
Türkçe
2016
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. FİLİZ ŞAHİN
- Investigation of the catalytic performance of tin nanowires produced by aluminum anodic oxide template method for electrochemical CO2 reduction
Alüminyum anodik oksit şablon yöntemiyle üretilen kalay nanotellerin elektrokimyasal CO2 redüksiyonuna yönelik katalitik performansinin i̇ncelenmesi
DİLAN ER GÖNÜL
Doktora
İngilizce
2023
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA KAMİL ÜRGEN