Bilgisayar destekli yeni bir yaklaşımla süperplastik şekil verme işlemlerinin analizi
A Computer aided new approach for analyzing superplastic forming processes
- Tez No: 105521
- Danışmanlar: DOÇ. DR. ABDULLAH MİMAROĞLU
- Tez Türü: Doktora
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Sonlu elemanlar analizi, süperplastik deformasyon, deformasyon hızı, 7075 Al alaşımı, 2024 Al alaşımı
- Yıl: 2001
- Dil: Türkçe
- Üniversite: Sakarya Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metalurji Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 161
Özet
ÖZET
Özet (Çeviri)
SUMMARY A COMPUTER AIDED NEW APPROACH FOR ANALYZING SUPERPLASTIC FORMING PROCESSES Keywords : Finite element analysis, superplastic deformation, strain rate, 7075 Al Alloy, 2024 Al Alloy Superplastic materials are polycrystalline solids which have the ability to show unusually high ductilities. Superplasticity is an important mode of deformation in metallic alloys with very small grain sizes and a deformation temperature of >0.5 Tm. If these conditions are fulfilled and maintained, then a material will show a high strain rate sensitivity of flow stress which is the most important mechanical characteristic of superplastic materials. For superplasticity, strain rate sensitivity(m) should be > 0.3. However, a high m does not necessarily result in a high tensile strain. A number of materials are prone to cavitation during superplastic flow, and this can lead to premature failure. In general, high elongations are observed over a rather limited range of intermediate strain rates and there is a decrease in the superplastic effect at both high and low strain rates. Although a fine grain size is an important requirement for superplasticity, it is not always possible to characterize the microstructure by this single parameter. It is important that the grain boundaries at high angle disordered. Other factors, including grain aspect ratio, grain size distribution, texture and the volume fractions of phases and their deformation characteristics can also influence superplastic behavior. Superplastic deformation is characterized by low flow stresses and this, combined with a high resistance to non-uniform thinning has lead to the superplastic forming of near net shape from sheet material. It is well established that grain boundary sliding is the primary deformation mode for superplastic flow. However, sliding between two grains cannot occur without the necessity for accommodation at the intersection with a third grain. Accommodation mechanisms are usually considered to determine the kinetics of superplastic flow, and may include diffusional and dislocational processes. Various theoretical models of superplasticity have been proposed, differing from each other primarily in the details of how the stress concentrations produced by grain boundary sliding. Superplasticity has been observed for a wide range of materials including metallic alloys, metal matrix composites, intermetallic phases, ceramics and minerals. A number of aluminum, titanium and nickel base alloys; aluminum based metal matrix composites have been used to produce aerospace parts. For titanium alloys the xviiisuccessive application of diffusion bonding and superplastic forming is used to produce relatively lightweight, complex cellular structures of high torsional rigidity. To take better advantage of the superplastic characteristics of the material, it is necessary to control the temperature and the strain rate during the manufacturing process. Since the material undergoes significant elongation, it also undergoes extreme thinning. The latter can be caused because of the particular geometry of the manufactured product, the characteristics of the material used, the lubrication, and the process parameters adopted. The design stage should take account of the real thickness distribution in order to avoid critical areas. The deformation process and variation of thickness should be controlled closely. At this stage, it is necessary, not only to design the product, but also to design the process in order to establish the optimum production parameters and to foresee the real geometry of the product. It is crucially important, in the process, to be able to control the pressure cycle in the order to obtain the optimum strain rate. To calculate optimum pressure cycle and for simulating the forming process, a finite element program can be used successfully. Numerical modeling can be used since analytical modeling would be limited only to some forms and to the use of largely approximated assumptions and experiments can be too expensive. The finite element method can be considered to be the most dependable both for analyzing complex geometry, and for taking into consideration all the phenomena involved in the manufacturing process. In this study, a different approach is proposed to use in the finite element analysis of superplastic deformation of strain rate sensitive material. The main aim is to model high deformation of strain rate sensitive materials by using basic flow rules that is not concerning the strain rate sensitivity. In this approach, a check and replacement schedule is used in the predefined time intervals. On the other hand an experimental study was also carried out. In the experimental study, two kind of aluminum alloys which are designated as 7075 and 2024 are rolled to the 0.55 mm, 0.40 mm and 0.25 mm thickness. Tensile test samples are machined from these rolled sheets. Uniaxial tensile tests were carried out at four different temperatures (475°C, 500°C, 525°C and 550°C) and five different initial strain rates (5xl0“3, lxlO”3, 5x10“*, 1x10^ and 5x1 0”5 sn1). In the finite element study tensile test sample is modeled, and three types of analysis is carried out. In the first analysis, displacement rates of each element are assumed as strain rates for each element. In the second analysis, strains of each element is calculated every predefined time intervals by the finite element analysis and strain rate of each element is calculated as strain change in the time period. In the third analysis, an equation which gives the strain rate of tensile test according to its gauge length and cross-head speed is used for the calculation of strain rates of each element. According to all these there definitions, results showed that each analysis type can be used for the finite element analysis of strain rate sensitive material's high deformation processes. A finite element computer code ANSYS was employed and used following a new approach. In this approach a step by step analysis was carried out and controlled to allocate a strain rate value with an element deformation. Having said using that the third definition face some restrictions. Furthermore, the finite element analyze is extended for the deformation process in a die. In these analysis two kind of time intervals are used. In the first attempt time interval is accepted as xixtotal analyze time. In the second attempt, the time interval is assumed as the difference between the last two check times. In both attempts, the results are in good agreement if the shape process takes place in a short time. Otherwise the second time interval method should be used. Finally, the experimental study results revealed that nearly all samples showed strain softening for the two types of aluminum alloys. It is shown that there is optimum temperature and strain rate range is present. The optimum process conditions can be given as 0.25 mm thickness, 525°C temperature and 5x1 0“4 s”1 strain rate. XX
Benzer Tezler
- Endüstri ürünleri tasarımı eğitimi ve girişimcilik arasında kurulabilecek etkileşim ve işbirlikleri: İTÜ ekosistemi üzerinden deneysel bir çalışma
Possible interactions and collaborations between industrial design education and startup: An experimental study on ITU ecosystem
OZAN SOYUPAK
Doktora
Türkçe
2019
Endüstri Ürünleri Tasarımıİstanbul Teknik ÜniversitesiEndüstri Ürünleri Tasarımı Ana Bilim Dalı
PROF. DR. HATİCE HÜMANUR BAĞLI
- Sayısal tasarım teknolojilerinde kullanılan üç boyutlu donanımların mimarlık eğitimine katkıları
Contrubition of three dimensional hardware used for digital design technologies on architectural education
ŞULE TOPÇUOĞLU
Yüksek Lisans
Türkçe
2007
MimarlıkYıldız Teknik ÜniversitesiMimarlık Ana Bilim Dalı
YRD. DOÇ. DR. TOGAN TONG
- Shipyard productivity evaluation with key performance indicators
Tersane üretim verimliliğinin temel performans göstergeleri ile değerlendirilmesi
ÜMRAN BİLEN
Doktora
İngilizce
2022
Gemi Mühendisliğiİstanbul Teknik ÜniversitesiGemi İnşaatı ve Gemi Makineleri Mühendisliği Ana Bilim Dalı
PROF. DR. ŞEBNEM HELVACIOĞLU
- Nörodejeneratif hastalıkların tedavisinde önemli rol oynayan monoamin oksidaz enzim (mao) inhibitörlerin bilgisayar destekli yöntemler kullanılarak tasarlanması
Design of monoamine oxidase enzyme (mao) inhibitors play important role in the treatment of neurodegenerative diseases using computer aided methods
YUSUF SERHAT İŞ
Doktora
Türkçe
2019
Kimyaİstanbul Teknik ÜniversitesiKimya Ana Bilim Dalı
PROF. DR. MİNE YURTSEVER
PROF. DR. SERDAR DURDAĞI
- Bulanık mantık ve tkinter destekli yarı otonom mobil arama kurtarma robot yazılımının geliştirilmesi
Development of fuzzy logic and tkinter supported semi-autonomous mobile search and rescue robot software
GAMZE NUR DAŞDEMİR
Yüksek Lisans
Türkçe
2024
Bilgisayar Mühendisliği Bilimleri-Bilgisayar ve KontrolÜsküdar ÜniversitesiYapay Zeka Mühendisliği Ana Bilim Dalı
PROF. DR. SERHAT ÖZEKES