Betonarme kirişlerin donatı hesabı
Calculation of reinforcement for the reinforced concrete beams
- Tez No: 114469
- Danışmanlar: PROF.DR. AHMET TOPÇU
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2001
- Dil: Türkçe
- Üniversite: Eskişehir Osmangazi Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 55
Özet
IV ÖZET Diğer betonarme elemanlarda olduğu gibi, betonun çekme kuvvetine karşı gösterdiği dayanım düşüktür. Bu düşüklükten dolayı basınç bölgesindeki beton, çekme bölgesindeki çelik çubuklar ile tam kapasiteyle çalıştırılmaya çalışılır. Bu yüzden çelik çubukları en uygun yerlere yerleştirmek için bilgi ve deneyim gerekmektedir. Donatının çeşidi ve miktarı hakkındaki boyutsal işlemler, betonarme kirişler için de kullanılır. Bunun yanı sıra, bu işlemler sonunda, beton ve çelik çubukların birlikte çalışmalarının kontrolleri hakkında kesit gibi bazı problemler ortaya çıkabilir. Bu yüzden bu tip problemlerin çözüm yolu her birinin boyutsal şekillerine göre hazırlanmış formül ve tablolardan yararlanarak farklı malzeme ve donatı kullanmaktır. Bu çalışmada, öncelikle tarafsız eksenin belirlendiği ve sonra da toplam donatı alanını hesaplayan bir bilgisayar programı geliştirilmiştir.
Özet (Çeviri)
SUMMARY The strenght of concrete against the tensile force is low as the other reinforced concrete components. Because of this, concrete at the compression zone is tried to work at full capacity by using the steel reinforcements at the tensile zone. The duty of steel reinforcements is to take the tensile force. For this reason, designing the steel reinforcements needs knowledge and experience. Designing type and quantity of steel reinforcements is used for the reinforced concrete beams, too. However, some problems may occur after this process, on the control of concrete and steel rods working together such as cross- section. For this reason, these problems are overcame by using different material and steel rod formulas and tables which were prepared according to their dimensons and shapes. In this study, a computer program developed which firstly determines the neutral axis and then calculates the total area of the reinforcement.
Benzer Tezler
- Lifli polimerle farklı biçimlerde güçlendirilmiş betonarme kirişlerin eğilme performanslarının belirlenmesi
Flexural performance evaluation of rc beams differently strengthened with fibre reinforced polymer
İLKNUR DALYAN
Doktora
Türkçe
2019
İnşaat MühendisliğiYıldız Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. BİLGE DORAN
- Farklı ıekilde donatılmış yüksek performanslı betonarme kirişlerin burulma momenti etkisindeki davranışlarının deneysel ve teorik olarak incelenmesi
Investigations of torsional behaviour of high performance reinforced concrete beams having different reinforcement arrangements under the pure torsion
ERTEKİN ÖZTEKİN
Doktora
Türkçe
2007
İnşaat MühendisliğiKaradeniz Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. METİN HÜSEM
- Yüksek performanslı betonarme kirişlerin minimum donatı oranının kırılma mekaniği esaslarına göre belirlenmesi
The determination of minimum reinforcement ratio of high performance reinforced beams based on fracture mechanics
MUHAMMED GÜMÜŞ
Yüksek Lisans
Türkçe
2016
İnşaat MühendisliğiGazi Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ABDUSSAMET ARSLAN
- GFRP donatılı betonarme kirişlerin eğilme, kesme ve aderans davranışı
Flexural, shear and bond behavior reinforced concrete beams with GFRP rebar
GÖKHAN BARIŞ SAKCALI
Doktora
Türkçe
2023
Deprem MühendisliğiBursa Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. İSA YÜKSEL
- Betonarme kirişlerin farklı lifli polimerle kesmeye göre güçlendirilmesi
Strengthening of shear critical reinforced concrete beams with various FRP systems
KADİR ŞENGÜN
Doktora
Türkçe
2023
İnşaat MühendisliğiYıldız Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. GÜRAY ARSLAN