Ferroelektrik KSr2Nb5O15 seramiklerinde şablon parçacıklar kullanılarak doku oluşturulması
Production of textured ferroelectric KSr2Nb5O15 ceramics by using template particles
- Tez No: 150205
- Danışmanlar: Y.DOÇ.DR. HÜSEYİN YILMAZ
- Tez Türü: Yüksek Lisans
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2004
- Dil: Türkçe
- Üniversite: Gebze Yüksek Teknoloji Enstitüsü
- Enstitü: Mühendislik ve Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 58
Özet
ÖZET 5£*(
Özet (Çeviri)
SUMMARY Concerning a certain property, some materials show different coefiBcj different crystallographic directions, this is called anisotropy. It can be given as a simple example that it is harder to cut a piece of wood perpendicular to its length than to cut it parallel to length. For some materials a similar situation is valid for electrical properties, those materials show maximum coefficients for electrical properties in a direction or set of directions. For such materials, when correctly electroded and poled a single crystal shows best electrical properties. However such disadvantages of single crystal growth as high cost, need for special conditions, limitations in dimensions and time consumption makes it difficult to use single crystal growth method especially in large scale production. An alternative to single crystal growth is the templated grain growth (TGG). TGG is based on forming crystallographic texture in polycrystalline materials using template particles. For some properties textured ferroelectric ceramics can show better properties compared to those of randomly oriented materials. In this work, ferroelectric KSraNbsOıs (KSN) ceramics with [001] textured microstructures were produced using KSN templates. Orientation of templates was carried out by tape casting method. Effects of sintering time and temperature, excess NbaOs and template content on density, microstructure and texture ratio were examined. Maximum amount of texture achieved is %98. This value is obtained by sintering the %10 template and %1.5 excess NbiOs containing sample at 1450°C for 6 hours.
Benzer Tezler
- Kristallografik olarak yönlendirilmiş anizometrik tek kristal piezoelektrik parçacıklara sahip piezokompozitleri temel alan yüksek hassasiyetli dokunsal sensörlerin geliştirilmesi ve karakterizasyonu
Development of high sensitivity tactile sensors based on piezocomposites with crystallographically oriented anisometric single crystal piezoelectric particles
HÜSEYİN ALPTEKİN SARI
Doktora
Türkçe
2025
Mühendislik BilimleriGebze Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. SEDAT ALKOY
- Synthesis and characterization of Fe3+ doped PbTiO3 nanopowders
Fe3+ ile zenginleştirilmiş nano boyuttaki PbTiO3 bileşiklerinin sentezi ve analizi
KAMİL KİRAZ
Yüksek Lisans
İngilizce
2009
KimyaKoç ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. MEHMET SUAT SOMER
- Ferroelektrik sıvı kristallerde elektrik alan etkisi altında SM A-SM C* faz geçişinin modellenmesi
Modeling of SME-SM C * phase transitions under electric field effect in ferroelectric liquid crystals
SİNAN AKSOY
Doktora
Türkçe
2019
Fizik ve Fizik MühendisliğiÇanakkale Onsekiz Mart ÜniversitesiFizik Ana Bilim Dalı
DOÇ. DR. MUSTAFA KURT
- Determination of the electrocaloric properties of the ferroelectric (1-x)BaTiO3-xBi(Li1/3Ti2/3)O3 (0≤x≤0.2) system
Ferroelektrik (1-x)BaTiO3-xBi(Li1/3Ti2/3)O3 (0≤x≤0.2) sisteminin elektrokalorik özelliklerinin belirlenmesi
TUĞÇE DEMİRTAY
Yüksek Lisans
İngilizce
2018
Metalurji Mühendisliğiİzmir Yüksek Teknoloji EnstitüsüMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
DR. UMUT ADEM
PROF. DR. MUHSİN ÇİFTÇİOĞLU
- Preparation and characterization of ferroelectric Pb (Zr,Ti) O3 films
Ferroelektrik Pb (Zr,Ti) O3 filmlerin hazırlanması karakterizasyonu
S.ÜMİT ERGİN
Yüksek Lisans
İngilizce
1997
Metalurji MühendisliğiOrta Doğu Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. MACİT ÖZENBAŞ