Geri Dön

El yatırma yöntemi ile elyaf takviyeli kompozit yapıların üretilmesi ve özellikleri

Production of fibre reinforced composite structures and their properties by the hand lay-up method

  1. Tez No: 201635
  2. Yazar: HÜROL YÖNEY
  3. Danışmanlar: YRD. DOÇ. DR. SEVHAN MÜGE YÜKSELOĞLU
  4. Tez Türü: Yüksek Lisans
  5. Konular: Tekstil ve Tekstil Mühendisliği, Textile and Textile Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2007
  8. Dil: Türkçe
  9. Üniversite: Marmara Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Teknoloji Eğitimi Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 194

Özet

El yatırma yöntemi ile elyaf takviyeli kompozit yapıların üretilmesinde genellikle keçe ve dokuma yapıdaki lifler takviye elemanı olarak seçilirken dayanımı ve elastikliğin arttırılması için cam ve karbon elyafından yapılmış çok eksenli kumaşların kullanıldığı bilinmektedir. Kompozit malzemelerin en basit uygulama yöntemlerinden olan el yatırma metodunda, bu amaçla yukarıda bahsedilen ve bilinen bu uygulamaların yerine bambu ve keten elyafı ve fitil şeridi kullanılarak doğal kökenli liflerde el yatırma yöntemi ile kompozit üretilmeye çalışılmıştır. Çalışmada 1.5 dtex/38 mm uzunluğunda bambu elyafı, Nm 0.93 bambu fitili ve ağartılmamış % 100 keten elyafı kullanılarak vinilester reçine ile farklı takviye yüzdelerinde çeşitli kompozit yapılar üretilmiştir. Üretilen doğal kökenli kompozit yapıların izod darbe dayanımı, çekme dayanımı ve üç nokta eğilme testleri yapılarak kırık yüzey analizleri elektron mikroskobunda incelenmiştir. Elde edilen sonuçlara göre bambu elyaf takviyeli kompozitlerde 3mm ve üstü uzunluklarda lif kullanımının mekanik özellikleri arttırdığı görülmüştür. Keten elyaf takviyeli numunelerde ise bambu elyafına göre daha iyi mekanik değerler elde edilmiştir. Keten elyafında yağ ve vaks tabakası uzaklaştırıldığında, işlem görmemiş elyafa göre daha iyi bir matris lif kaynaşmasının meydana geldiği görülmüş ve darbe dayanımında % 50'ye varan artışlar gözlemlenmiştir.

Özet (Çeviri)

Generally felt and woven fabrics are selected as a reinforcement component of fibre reinforced composite structures which are produced with hand lay-up method. It is known that multiaxial fabrics consist of glass and carbon fibres are used to increase the mechanical properties. In this study, instead of glass and carbon fibres mentioned above, the composite structures with hand lay-up method by using natural fibers of flax bamboo and bamboo sliver were produced. At this study the composite structures with vinylester resin and bamboo fibres with 1.5dtex/38 mm staple length, Nm 0.93 bamboo sliver and 100 % unbleached flax fibres at different reinforcement ratios had been produced. After producing, the natural fiber reinforced composites three point bending, tensile strength and izod impact strength tests were carried out and fracture surfaces of the samples had been inspected on the scanning electron microscope. According to the results, it has been evaluated that bamboo fibres with 3 mm fibre length and above increases the mechanical properties of composite structures. The increament of the mechanical properties of the reinforced samples with flax fibres have shown considerably higher properties than bamboo reinforced fibres. Better combination has observed between resin and fibres of the samples which had been produced with flax fibres that are purified from wax and grease. Also approximately 50 % increament has been reached on the izod impact strength of these samples.

Benzer Tezler

  1. CNC / Cam Elyaf / epoksi hibrid kompozitlerin mekanik ve termal özelliklerinin incelenmesi

    Investigation of mechanical and thermal properties of CNC / Glass Fiber / epoxy hybrid composites

    FATİH ACER

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Mühendislik BilimleriManisa Celal Bayar Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ SUAT BAHAR BAŞTÜRK

  2. Hibrit fiber kompozit malzemelerin mekanik özelliklerinin deneysel olarak incelenmesi

    Experimental investigation of mechanical properties of hybrid fiber composite materials

    FATİH EMİR DANYILDIZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Makine MühendisliğiSakarya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DOÇ. DR. SEÇİL EKŞİ

  3. Bazalt elyaf takviyeli nanokompozit malzemelerin delmeişlemlerinde takım ucu geometrisinin etkisinin araştırılması

    Drilling of basalt fiber reinforced nanocomposite materialsinvestigation of the effect of tool nose geometry on operations

    MEHMET KASTA

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Makine MühendisliğiAmasya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DOÇ. DR. HALİL BURAK KAYBAL

  4. Elyaf takviyeli hibrit kompozit malzemelerin darbe davranışlarının incelenmesi

    The investigation of impact behaviors of fiber reinforced hybrid composite materials

    ABDULSAMET GÖR

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Makine MühendisliğiUşak Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. OSMAN ASİ

  5. Elyaf takviyeli kompozit malzemelerde üretim parametrelerinin malzemenin mekaniksel ve fiziksel özelliklerine etkisinin incelenmesi

    Investigation of the effect of production parameters on the mechanical and physical properties of material in fiber reinforced composite materials

    FADİME KÜBRA DEMİR

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiUşak Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. OSMAN ASİ