Production and design of FDM (fused deposition modeling) type rapid prototyping machine with extrusion head unit
Harç yığma tekniği ile modelleme yapan hızlı prototipleme makinesi ve ekstrüzyon kafası tasarımı ve üretimi
- Tez No: 259092
- Danışmanlar: DOÇ. DR. BÜLENT EKİCİ
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2009
- Dil: İngilizce
- Üniversite: Marmara Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 78
Özet
Bu projenin amacı hızlı prototipleme teknolojisini, avantajlarını, hızlı prototipleme makinelerinin teknolojisini, kontrolünü açıklamak ve Fused Deposition Modeling tipi bir hızlı prototipleme makinesin tasarımı ve üretimini yapmaktır.Tübitak'ın desteklediği projede hedeflenen katman katman üretim yöntemi ile prototip üretebilen bilgisayar kontrollü makinede alışılagelmiş üç eksenli kartezyen robota ilave olarak teli süren dördüncü bir eksen daha kullanılmaktadır. Bu dördüncü eksen C ekseni olarak tanımlanmaktadır. Prototip makinede sistemin çalışması, birbirinden farklı alt sistemlerin doğru olarak üretilmesine bağlıdır. Bu alt sistemler kartezyen robot, plastik teli süren ekztruder kafa, ve sistemi çalıştıran yazılımdır.Tasarlanan makine nümerik olarak kontrol edilmeliydi. Kafanın X,Y ve Z yönlerinde hareket etmesi için 3 hareket kaynağına ihtiyaç vardır. Step motorlar uygun fiyatları ve isabet oranları nedeniyle hareket kaynağı olarak seçildi. Nümerik kontrol temelleri ve step motorlarla ilgili temel bilgiler üretim aşamalarından önce anlatıldı.Step motorların hareket kaynağı olarak seçilmesinden sonra, bu motorların sürücü birimleri satın alındı. Bu sürücülerin aynı zamanda bilgisayar ile bağlantıya geçmesi için, seri port ara yüzü satın alındı. Sistemi besleyebilmek için yüksek dereceli güç kaynağı üniteleri satın alındı. Kontrolör ünitenin ve güç kaynağının bir kasaya montajından sonra, seri port arayüzü ile birlikte gelen DeskCNC programı yön ve step miktarı için gerekli sinyalleri üretmekte kullanıldı.Elektrik ve elektronik işlerinden sonra, kasayı oluşturan paslanmaz çelik profiller, alüminyum X-Y tablasına yapıştırıldı, Z ekseni de kelepçeler yardımı ile kasaya monte edildi. X-Y motorlarının dairesel hareketi zaman kayışı ve kasnak yardımıyla konveyör sistemi şeklinde lineer harekete dönüştürüldü. Z ekseni için de bilyalı mil ve kasnak sistemi kullanılarak lineer hareket sağlandı. Aynı zamanda rezistanslar ve PID kontrollü termostatlar sac metal gövdeye tutturuldu.
Özet (Çeviri)
The purpose of this project is to explain rapid prototyping technology, the advantages of rapid prototyping machine and technology, the control of the machines, and the design and production of fused deposition modeling type rapid prototyping machine. In this project supported by Tübitak, a fourth axis is also used to provide plastic wire driving mechanism in addition to the conventional 3 axis Cartesian robot. This fourth axis is called as C axis. The success of the overall prototyping machine depends on the success of individual subsystems. Based on the knowledge that I?ve gained from undergraduate thesis, numerical control machine should be designed for the basis of layered production type rapid prototyping machine. Head unit should move in X, Y and Z direction and is needed source for motion. Step motors are selected due to hit rates and competitive prices, as a source of movement. Basic information about fundamentals of numerical control and step motors was described before production stages. After selecting the source of the movement as step motors, the driver of the motor units purchased. At the same time, serial port interface card was purchased for connection with PC. Step motors need direct current to work, to provide this, power supply units were purchased. The controller and power supply unit assembled into a case and DeskCNC program selected to generate necessary signals from G codes. After electric and electronic works, case of rapid prototyping machine was produced from sheet metal and stainless steel profiles. Aluminum X-Y table fixed to the top of stainless steel profiles and Z axis mounted to the steel profiles with the help of clamps. Rotary motion of X ? Y axis stepper motors was converted to the linear motion with the help of trigger belt and pulley system and for Z axis stepper motor rotary motion was converted to the linear motion with ball-screw and linear bearings. At the same time resistances and PID-controlled thermostats were mounted to the housing. After mechanical works stepper motors and drivers were attached to the system.
Benzer Tezler
- Hızlı prototip üretim teknolojileri
Başlık çevirisi yok
LEVENT YAĞMUR
Yüksek Lisans
Türkçe
1997
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Malzemesi ve İmalat Teknolojisi Ana Bilim Dalı
YRD. DOÇ. DR. MUZAFFER ERTEN
- Eriyik yığma tekniği ile çalışan üç boyutlu yazıcı tasarımı, imalatı ve elde edilen numunelerin bazı özelliklerinin belirlenmesi
Design and production of fused deposition modelling type three dimensional printer and determination of some properties of samples
HASAN BAŞ
Yüksek Lisans
Türkçe
2017
Mühendislik BilimleriOndokuz Mayıs ÜniversitesiAkıllı Sistemler Mühendisliği Ana Bilim Dalı
DOÇ. DR. FATİH YAPICI
- Katmanlı imalat yöntemi ve talaşlı imalat yöntemi için optimizasyon yöntemlerinin denenmesi ve karşılaştırılması
Testing and comparison of optimization methods for layered manufacturing method and mechanic manufacturing method
HALİL TOSUN
Yüksek Lisans
Türkçe
2021
Makine MühendisliğiManisa Celal Bayar ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ AHU ÇELEBİ
- Eklemeli imalat yöntemlerinde üretim parametrelerinin ve parça geometrisinin son ürün özellikleri üzerindeki etkilerinin incelenmesi
Investigation of the effects of production parameters and part geometry on the final product properties in additive manufacturing methods
AYSU HANDE YÜCEL
Yüksek Lisans
Türkçe
2021
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA BAKKAL
- Production and characterization of simple, face-centered and diamond cubic lattices by fused deposition modeling using polylactic acid
Polilaktik asitten eriyik yığma yöntemiyle üretilen basit, yüzey merkezli ve elmas kübik yapıların karakterizasyonu
ARİF DÖNMEZ
Yüksek Lisans
İngilizce
2022
Makine MühendisliğiOrta Doğu Teknik ÜniversitesiMühendislik Bilimleri Ana Bilim Dalı
PROF. DR. ZAFER EVİS