Geri Dön

Bakırın tel çekme işlemi esnasında meydana gelen tozlanma sorununun incelenmesi

Investigation of dusting problem during copper wire drawing

  1. Tez No: 291941
  2. Yazar: FERHAT OMAÇ
  3. Danışmanlar: PROF. DR. E. SABRİ KAYALI
  4. Tez Türü: Yüksek Lisans
  5. Konular: Metalurji Mühendisliği, Metallurgical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2010
  8. Dil: Türkçe
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 95

Özet

Bu çalışmada abrasif aşınma, yüzey deformasyonu aşınması, adezif aşınma ve delaminasyon aşınması gibi çeşitli toz oluşum mekanizmalarının detaylı bir tanımı yapılmış ve bu mekanizmaları etkileyebilecek/hızlandırabilecek çeşitli faktörler (kullanılan yağlayıcı, filtreleme, tel çekme sıcaklığı vs.) açıklanmıştır. Burma testi esnasında bakır filmaşinlerden dökülen tozların XRD analiz yöntemi ile Cu2O bileşiminde olduğu, kimyasal analiz yöntemi ile % 90 gibi bir bölümünün CuO ve Cu2O karşımı olduğu belirlenmiştir. Böylece filmaşinin burma testi esnasındaki tozlanmanın nedeninin filmaşinin yüzeyindeki oksit tabakası olduğu anlaşılmıştır ve bu bulgu literatür ile uyum içindedir.Filmaşinlerin yüzeyindeki oksit tabakasının %20 HCl çözeltisi ile temizlenmesi sonucunda tozlanma miktarının azaldığı ancak tozlanmanın devam ettiği tespit edilmiştir. Bu tespit tozlanma olayının sadece yüzeydeki oksit tabakası ile ilişkisi olmadığını tozlanmaya ayrıca yüzey altı oksitlerinin de katkısı olduğunu göstermektedir.

Özet (Çeviri)

In this study a detailed description of the various dust formation (or fine generation) mechanisms such as abrasive wear, surface deformation wear, adhesive wear and delamination wear are made and various factors that may accelerate these mechanisms (lubricant, filtration, wire drawing temperature etc. ) are discussed. That fines formed on the surface of copper rod during twist tests were determined as Cu2O by XRD analysis method. Thereby, it?s defined that a reason of the dusting during copper rod?s twist test is oxide layer on the surface of copper rod and this result is in agreement with the literature. From the wet chemical analysis of the fines, collected from twist tests it was determined that / 90 of these fines are the mixture of CuO and Cu2O.After the cleaning of oxide layer on the surface of copper rod, it?s determined that the dusting was reduced but it?s still proceeding. This determination shows that the dusting is not only related to surface oxide layer but also is associated with subsurface oxide layer.XRD analysis of the fines collected from inside of the wire drawing machine and it?s emulsion filter shows that they are copper. The fines collected from inside of the wire drawing machine and it?s emulsion filter were exhaustively examined by SEM and it?s distinguished that this fines were formed by delamination wear.

Benzer Tezler

  1. Investigation of the microstructural and mechanical properties of Al/TiB2 composites produced by cold spray additive manufacturing

    Soğuk sprey eklemeli imalat yöntemi ile üretilen Al/TiB2 kompozitlerinin mikroyapı ve mekanik özelliklerinin incelenmesi

    NERGİZ İLHAMİ MERT

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. MURAT BAYDOĞAN

  2. Tel çekme işleminde bakırın ve bakır oksit inklüzyonlarının deformasyon davranışı

    Deformation behaviour during drawing of copper wires and copper oxide inclusions

    MUSTAFA M. ARIKAN

    Yüksek Lisans

    Türkçe

    Türkçe

    1991

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    PROF.DR. E. SABRİ KAYALI

  3. Grafit mikrofiber esaslı metal matrislikompozit yatak malzemesi tasarımı, üretimi,mekanik ve tribolojik özelliklerininaraştırılması

    Composite bearing material design, production, investigation of mechanical and tribological properties

    ÖMER BARIŞKAN YASAN

    Doktora

    Türkçe

    Türkçe

    2022

    Makine MühendisliğiErciyes Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. SEDAT ÖZDEN

    YRD. DOÇ. DR. FAZIL CANBULUT

  4. Saf bakırın soğuk deformasyon ve yeniden kristalleşme davranışının mikroyapı ve mekanik özelliklere etkisi

    The effect of cold deformation and recrystallization behavior on microstructure and mechanical properties of pure copper

    CEM AKBAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    Metalurji Mühendisliğiİstanbul Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. SELİM YILDIRIM

  5. The Effect of process parameters on the mechanical properties of drawn copper wires

    Başlık çevirisi yok

    MEHMET YAMAN AKYOL

    Yüksek Lisans

    İngilizce

    İngilizce

    1990

    Makine MühendisliğiBoğaziçi Üniversitesi

    PROF.DR. SABRİ ALTINTAŞ