Geri Dön

Polipropilen lif takviyeli betonların yüksek sıcaklık etkilerinden sonra basınç dayanımlarının incelenmesi

The compressive strength of polypropylene fiber reinforced concrete exposed to elevated temperature

  1. Tez No: 324740
  2. Yazar: MAJID ATASHAFRAZEH
  3. Danışmanlar: YRD. DOÇ. DR. A. FERHAT BİNGÖL
  4. Tez Türü: Yüksek Lisans
  5. Konular: İnşaat Mühendisliği, Civil Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2013
  8. Dil: Türkçe
  9. Üniversite: Atatürk Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 96

Özet

İnşaat Mühendisliği alanında, sağladığı avantajlar bakımından lifli betonların önemi hızla artmaktadır. Lifli beton; çimento, agrega ve çoğunlukla süreksiz dağılı liflerin su ile karıştırılmasıyla elde edilen beton olarak tanımlanmaktadır.Beton yüksek sıcaklık etkisinde kaldığında önemli ölçüde hasara uğrar. Bu durum istenmeyen yapısal kusurlara neden olabilir. Polipropilen liflerin ilavesi bu hasarın azaltılmasında kullanılan yöntemlerden biridir. Bu çalısmada lif katkısız, 300, 600, 900 ve 1200g/m³ polipropilen elyaf (yün) ve çubuk lif katkılı kullanılarak beton numuneler üretilmiştir. Polipropilen elyaf lifin boyu 12 mm ve polipropilen çubuk lif 40 mm boyunda kullanılmıştır. Numuneler laboratuar ortamında kür edilmiş, 28. günün sonunda tüm numuneler 23°C, 150°C, 300°C, 450°C, 600°C ve 750°C sıcaklık etkisine maruz bırakılmıştır. Yüksek sıcaklık etkisinde kalan numunelerin başlıklama yaptıktan sonra basınç dayanımları belirlenmiştir.En yüksek basınç dayanımı 300g yünsü polipropilen katkılı numunelerde tespit edilmiştir. Bu grup için dayanım artışı %8 olarak belirlenmiştir. Yüksek sıcaklık etkilerinden sonra dayanımda çubuk polipropilen lifler yünsü polipropilen liflere göre daha iyi sonuçlar göstermiştir. Ayrıca veriler göstermiştir ki her iki lif grubu için 600°C den sonra lifsiz numuneler daha iyi sonuç vermiştir. Bunun nedeni olarak 500°C den yüksek sıcaklılarda polipropilen liflerin erimesiyle, boşluklu bir ortam oluşumuna sebep olması düşünülebilir.

Özet (Çeviri)

In the field of civil engineering, the importance of fiber concrete is rapidly increasing. Cement, aggregate and distribution of fibers by mixing water is defined as a polypropylene fiber reinforced concrete (PFRC).Concrete undergoes significant damages when it is under the effect of high temperature. This may cause undesirable structural defects. The addition of polypropylene fibers is one of the methods used to reduce this damage. In this study, the concrete specimens without any fibers (control specimens), 300gr/m³, 600gr/m³, 900gr/m³ and 1200gr/m³ polypropylene fibers were produced both in woolen and rod shape. The length of woolen polypropylene fiber was 12mm and for the rod type was 40 mm. The specimens were matured in the laboratory environment. At the end of 28th day, they were left at 23°C, 150°C, 300°C, 450°C, 600°C and 750°C for 2 hours. Then after capping the specimens, the compressive strength of them was determined.The maximum compressive strength was determined in samples observed to 300gr/m³ of woolen polypropylene. For this group, the compressive strength increase was 8%. In the fire resistance strength, the rod polypropylene fibers showed better result than woolen polypropylene fibers. On the other hand, the results showed that beyond the both fiber groups, the control specimens gave the best result after the temperature of 600°C. This is because of the melting of polypropylene fibers after 500°C, as well as the fibers obstacle to explode but it leads to the formation of porous media and caused the reducing of the compressive strength.

Benzer Tezler

  1. Yüksek sıcaklık ve donma-çözülme etkisine maruz kalmış lif içeren ultra yüksek dayanımlı betonların özellikleri

    Properties of ultra high strength concrete containing fiber exposed to high temperature and freeze-thaust

    TUBA BOZBAY AKTAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    İnşaat MühendisliğiMersin Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    PROF. DR. CAHİT BİLİM

  2. Yüksek sıcaklık etkisinden hasar görmüş lifli, hava sürükleyici katkılı ve perlit agregalı betonların dayanım özellikleri ve GFRP ile onarımı ve güçlendirilmesi

    Strength properties of concretes with fiber, entrained air and expanded perlite aggregates after exposure to high temperatures and confinement with GFRP

    OZAN SEÇER

    Yüksek Lisans

    Türkçe

    Türkçe

    2008

    İnşaat MühendisliğiAtatürk Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. İBRAHİM TÜRKMEN

  3. Polipropilen lif ile güçlendirilmiş köpük betonlarda taban külünün hafif agrega olarak kullanımının araştırılması

    Utilization of bottom ash as lightweight aggregate in foam concretes

    DUYGU ÖZTÜRK YARAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    İnşaat MühendisliğiKastamonu Üniversitesi

    Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ OĞUZHAN YAVUZ BAYRAKTAR

  4. Polipropilen lif takviyeli kendiliğinden yerleşen betonların performans özelliklerinin araştırılması

    The investigation of performance charecteristics polypropylene fiber reinforced sel compacting concretes

    MEHMET AKTÜRK

    Yüksek Lisans

    Türkçe

    Türkçe

    2007

    İnşaat MühendisliğiSelçuk Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    Y.DOÇ.DR. RIFAT SEZER

  5. Çelik ve polipropilen lif ilavesinin betonun davranışına etkisi: Statik ve dinamik değerlendirme

    Effect of steel and polypropylene fiber addition on concrete behavior: Static and dynamic evaluation

    FATİH ALİ ÖNCEL

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    İnşaat MühendisliğiAdıyaman Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DOÇ. DR. MEHMET FATİH ŞAHAN