Effects of moisture after injection on the mechanical properties of PA 6 and PA 66 materials
PA 6 ve PA 66 malzemelerinde enjeksiyon sonrası nemin mekanik özelliklere etkisi
- Tez No: 343008
- Danışmanlar: DOÇ. DR. EMİNE ÇINAR YENİ
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Polyamide, moisture content, mechanical properties
- Yıl: 2013
- Dil: İngilizce
- Üniversite: Dokuz Eylül Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 51
Özet
Endüstriyel uygulamalarda geniş bir kullanım alanı olan polyamidler, ilk mühendislik plastikleridir. Bu malzemeler neme çok duyarlıdır ve nem plastikleştirici olarak etki gösterir. Alınan nem miktarının artması ile malzemelerin dayanımı azalırken, süneklik ve uzama miktarları artmaktadır. Malzeme içerisindeki yüksek nem miktarı, malzemenin darbe dayanımını ve tokluk değerlerini iyileştirmektedir. Bu tezde enjeksiyon metodu ile, PA 6 ve PA 66 malzemelerin ASTM D 618 standardına uygun olarak imal edilmiş olan çekme numunelerinin nem almasının mekanik özelliklere etkisi incelenmiştir. Çekme numuneleri 80 santigrat derece su içerisinde 3 farklı zaman periyodunda şartlandırılmışlardır. 10, 20 ve 30 saat şartlandırmaları numunelere uygulanmıştır. Şartlandırma sonrası numuneler çevre etkilerinden korunmaları için yüksek yoğunluklu polietilen torbalar içerisinde saklanmışlar ve belirli zaman periyotlarında numunelere çekme testi uygulanmıştır. 10, 20, 30 saat test numunelerinin gerilim - şekil değişimi eğrileri çizilmiş ve sonuçları değerlendirilmiştir. Gözlemler sonucunda PA 6 ve PA 66 malzemelerinin nem alma sonrasında akma ve kopma mukavemetlerinin azaldığı; süneklik, darbe dayanımı ve yüzde uzama değerlerinin artığı görülmüştür. Poliamid malzemesisinin imalat şartlarının, elde edilen ürüne nedenli büyük bir etkisi olduğu, aynı şartlandırmaya maruz kalmış test numuneleri ile yapılan deneylerde görülmüştür.Anahtar sözcükler : Poliamid, nem miktarı, mekanik özellikler
Özet (Çeviri)
Polyamides are among the first engineering plastics which have a wide variety of usage in industrial applications. These materials are very sensitive to moisture which acts as a plasticiser. With the increasing of absorbed moisture, strength and stiffness reduces but toughness and elongation increases. Higher moisture levels improve the impact absorbtion ability and ductility. In this thesis, the effects of moisture absorbtion on mechanical properties of PA 6 and PA 66 materials were investigated using tensile test specimens which had the dimensions in accordance with ASTM D 618, which were prepared by using the injection molding method. The tensile test specimens were conditioned in 80 celcius degrees water with three different time periods. 10, 20 and 30 hours immersions were applied. After conditioning, specimens were isolated from the environment by the help of HDPE bags and tensile tests were conducted for every specimen at certain time periods. Stress ? strain curves were drawn for 10, 20, 30 hours test specimens and the results were compared with each other. It has been observed that after conditioning of PA 6 and PA 66 materials, the yielding and ultimate strength decreased; toughness, impact absorbtion ability and strain rates increased. The importance of production conditions of polyamide materials were realised with the help of tensile tests which consisted of same conditioned test specimens.
Benzer Tezler
- Karşı gaz basınçlı plastik enjeksiyon kimyasal köpürtme üretim yönteminde proses parametrelerinin gözenek yapısı ve yüzey parlaklığına etkilerinin incelenmesi
Analysis the effects of process parameters on pore structure and surface gloss in chemical foaming plastic injection molding process with gas counter pressure
BURAK ERKAN
Yüksek Lisans
Türkçe
2022
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. ALİ GÖKŞENLİ
- Investigation of the effects of various types of plasticizers on the properties of polyester polyol based thermoplastic polyurethane
Farklı plastifiyan tiplerinin, polyester polyol bazlı termoplastik poliüretan üzerindeki etkilerinin araştırılması
BAHAR DURAK
Yüksek Lisans
İngilizce
2016
Polimer Bilim ve Teknolojisiİstanbul Teknik ÜniversitesiPolimer Bilim ve Teknolojisi Ana Bilim Dalı
PROF. DR. NURSELİ UYANIK
- Plastik dişli çarkların konstrüktif özelliklerinin incelenmesi
Analysis of the design characteristics of the plastic gears
CÜNEYT FETVACI
- A356, A357 ve F357 alüminyum döküm alaşımlarının hassas döküm tekniği ile üretimi ve karakterizasyonu
Production of A356, A357 and F357 aluminum casting alloys by precision casting technique and characterization
MERVE SANCAR COŞKUN
Yüksek Lisans
Türkçe
2021
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. CEVAT BORA DERİN
- Preparation and characterization of poly(ethylene terephthalate) polypropylene blends
Poli(etilen teraftalat) polipropilen blendlerinin hazırlanması ve karakterizasyonu
GÜLÇİN TORUNOĞLU TURAN
Yüksek Lisans
İngilizce
2012
Polimer Bilim ve Teknolojisiİstanbul Teknik ÜniversitesiPolimer Bilim ve Teknolojisi Ana Bilim Dalı
PROF. DR. NURSELİ UYANIK
DOÇ. DR. TUNCER YALÇINYUVA