Geri Dön

Endüstri tesislerinde aydınlatma

Industrial lighting

  1. Tez No: 39796
  2. Yazar: UĞUR ARAS
  3. Danışmanlar: Y.DOÇ.DR. SERMİN ONAYGİL
  4. Tez Türü: Yüksek Lisans
  5. Konular: Elektrik ve Elektronik Mühendisliği, Electrical and Electronics Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 1994
  8. Dil: Türkçe
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 81

Özet

Özet yok.

Özet (Çeviri)

The Solutions mere obtained by using fluorencent lamps, high pressure mercury vapour lamps, high pressure sodium lamps and metal halide gas-discharge lamps. With these lamps calculations were done by taking the height as 5, 7, and 9 meters. After the calculation with the same configuration of the lighting design, computations mere repeted by putting vertical partitions and horizontal surfaces into the room. For all examples cost analysis has been done. The examples has been selected from the car factory. At the end of lighting calculations the average illuminances and Emin/Eave uere compared. It has been seen that the systems with fluorescent lamps are the most expensive solutions. For the height of 5 meters with the high peressure sodium lamps, metal halide gas-discharge lamps, the values of Emin/Eave are not good. Fdt the other heights all HID lamps can be used. -x-Unreplaced burneout lamps mill vary in quantity depending an the kinds of lamps and the relamping program used. Manufacturers mortality statiscs should be consulted for the performance of each lamp type to determine the number expected to burnout before the time of planned replacement is reached. The total light loss factor (LLF) is simplfy to product of multiplying all the contributing factors described above. Where the factors are not known, or applicable they are assumed to be unity. At this point, if it is found that the total light loss factor is excessive it may be desirable to reselect the luminaire. Fig-1. Illustrates the particular cases where the plane on which the illuminance is to be determined either horizontal or vertical. H is the vertical mounting height of the light source above the plane of measurement; R is the horizontal distance from the light source to the point; and I is the candle power of the source to the point. For the horizontal plane, angle equals angle©. Further more, since CD50=CDS p = H/D, n, tr ^ I.CDS8 - I-COSP Illuminance on Horizontal Plane Uh; = -“ D2 Dz Illuminance on vertical Plane (E,;) = I. sinG I. CDS/3 /jW\ > 10 N. 'sy \ ILLUMINANCE (CM THE HORIZONTAL PLANE) CANDLEPQWER x COS 6 D2 L. \ \ ft \ -J ^1 NORMAL ILLUMINANCE,'ON THE VERTiCAl P'.ANf) CANDLEPQWER » SIN 6 D2 Fig: 1. Fundamental Relationships For Point Calculations, -IX-The Solutions mere obtained by using fluorencent lamps, high pressure mercury vapour lamps, high pressure sodium lamps and metal halide gas-discharge lamps. With these lamps calculations were done by taking the height as 5, 7, and 9 meters. After the calculation with the same configuration of the lighting design, computations mere repeted by putting vertical partitions and horizontal surfaces into the room. For all examples cost analysis has been done. The examples has been selected from the car factory. At the end of lighting calculations the average illuminances and Emin/Eave uere compared. It has been seen that the systems with fluorescent lamps are the most expensive solutions. For the height of 5 meters with the high peressure sodium lamps, metal halide gas-discharge lamps, the values of Emin/Eave are not good. Fdt the other heights all HID lamps can be used. -x-Unreplaced burneout lamps mill vary in quantity depending an the kinds of lamps and the relamping program used. Manufacturers mortality statiscs should be consulted for the performance of each lamp type to determine the number expected to burnout before the time of planned replacement is reached. The total light loss factor (LLF) is simplfy to product of multiplying all the contributing factors described above. Where the factors are not known, or applicable they are assumed to be unity. At this point, if it is found that the total light loss factor is excessive it may be desirable to reselect the luminaire. Fig-1. Illustrates the particular cases where the plane on which the illuminance is to be determined either horizontal or vertical. H is the vertical mounting height of the light source above the plane of measurement; R is the horizontal distance from the light source to the point; and I is the candle power of the source to the point. For the horizontal plane, angle equals angle©. Further more, since CD50=CDS p = H/D, n, tr ^ I.CDS8 - I-COSP Illuminance on Horizontal Plane Uh; = - ”D2 Dz Illuminance on vertical Plane (E,;) = I. sinG I. CDS/3 /jW\ > 10 N. 'sy \ ILLUMINANCE (CM THE HORIZONTAL PLANE) CANDLEPQWER x COS 6 D2 L. \ \ ft \ -J ^1 NORMAL ILLUMINANCE,'ON THE VERTiCAl P'.ANf) CANDLEPQWER » SIN 6 D2 Fig: 1. Fundamental Relationships For Point Calculations, -IX-The Solutions mere obtained by using fluorencent lamps, high pressure mercury vapour lamps, high pressure sodium lamps and metal halide gas-discharge lamps. With these lamps calculations were done by taking the height as 5, 7, and 9 meters. After the calculation with the same configuration of the lighting design, computations mere repeted by putting vertical partitions and horizontal surfaces into the room. For all examples cost analysis has been done. The examples has been selected from the car factory. At the end of lighting calculations the average illuminances and Emin/Eave uere compared. It has been seen that the systems with fluorescent lamps are the most expensive solutions. For the height of 5 meters with the high peressure sodium lamps, metal halide gas-discharge lamps, the values of Emin/Eave are not good. Fdt the other heights all HID lamps can be used. -x-

Benzer Tezler

  1. Endüstri tesislerinde enerji verimli aydınlatma teknikleri ve örnek çalışma

    Energy efficiency lighting techniques in industrial plants and a case study

    MEHMET REHA GÖKMEN

    Yüksek Lisans

    Türkçe

    Türkçe

    2010

    Enerjiİstanbul Teknik Üniversitesi

    Enerji Bilim ve Teknoloji Ana Bilim Dalı

    PROF. DR. SERMİN ONAYGİL

  2. Tipik bir karargahta yenilenebilir enerji uygulamaları potansiyelinin araştırılması

    Research of practicing renewable energy potential in typical headquarters

    İBRAHİM BÜLBÜL

    Yüksek Lisans

    Türkçe

    Türkçe

    2007

    Endüstri ve Endüstri Mühendisliğiİstanbul Ticaret Üniversitesi

    Endüstri Mühendisliği Ana Bilim Dalı

    PROF.DR. ERALP ÖZİL

  3. Data-driven condition monitoring and fault diagnosis of VFD-FED induction motors

    Değişken frekanslı sürücü ile beslenen asenkron motorlarda veri odaklı durum izleme ve arıza tanılama

    ALPER SENEM

    Yüksek Lisans

    İngilizce

    İngilizce

    2021

    Elektrik ve Elektronik Mühendisliğiİstanbul Teknik Üniversitesi

    Mekatronik Mühendisliği Ana Bilim Dalı

    PROF. DR. ŞENİZ ERTUĞRUL

  4. Avrupa ülkelerindeki gazometre yapılarının çelik yapıların gelişimi bağlamında irdelenmesi ve Dolmabahçe gazometresi için işlevlendirme önerisi

    The study of gasometers in European countries in the context of development of steel structures and the re-functioning proposal for Dolmabahce gasometer

    ELİF TÜRKEL

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    Mimarlıkİstanbul Teknik Üniversitesi

    Mimarlık Ana Bilim Dalı

    YRD. DOÇ. DR. HALET ALMILA BÜYÜKTAŞKIN

  5. Endüstri mirasının korunması kapsamında atıl mekanlar olarak gazhane yapılarının dönüşümünün incelenmesi

    Investigation of the transformation of gasometer buildings as installed places within the conservation of industrial heritage

    SEMA NUR ALBAYRAK TAŞTEMİR

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    Mimarlıkİstanbul Sabahattin Zaim Üniversitesi

    Mimarlık Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ BAHAR FERAH