Geri Dön

Elastic-plastic characterization of cracks on ductile bimaterial interfaces

Başlık çevirisi mevcut değil.

  1. Tez No: 400038
  2. Yazar: ERMAN ÇITIRIK
  3. Danışmanlar: PROF. HERMAN F. NİED
  4. Tez Türü: Doktora
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2006
  8. Dil: İngilizce
  9. Üniversite: Lehigh University
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 154

Özet

Özet yok.

Özet (Çeviri)

In this study, linear elastic and elastic plastic finite element computations areperformed to characterize nonlinear fracture behavior on ductile bimaterial interfaces.Nonlinear behavior is obtained directly from finite element computations withoututilizing any pre-defined embedded singularity at the crack tip. Analytic expressionsobtained for linear elastic fracture mechanics are employed to define boundaryconditions in both linear elastic and elastic-plastic analyses. Ramberg-Osgoodnonlinear material model is embedded into a finite element source code to characterizeuniaxial stress-strain behavior. This nonlinear material model is employed in all elasticplastic analyses to determine the nonlinear stress strain fields at the interface crack tip.The analytic solution for a finite homogeneous crack in an infinite mediumobtained in 1968 by Hutchinson-Rice-Rosengren, which is also called the HRRsolution, is reproduced by employing a fourth-order Runge-Kutta method. Theproblem formulated was a fourth order nonlinear eigenvalue problem. The computedsolution is employed in the comparison of elastic plastic finite element resultscomputed at the homogeneous crack tip. Two different finite element meshes aredeveloped for finite element computations and they are employed in the homogeneousfracture problem. Only the second mesh is utilized in the interface fracturecomputations. The computed linear elastic finite element results are compared tolinear elastic analytic results, and elastic plastic results are compared to the HRRresults. The comparisons conducted for both analyses were sufficiently close to2proceed with a detailed examination of the elastic-plastic interface fracture problem.Finally, J integral computations at the interface crack tip were performed tocharacterize the nonlinear interface fracture behavior for different combinations ofmaterial variables and loading values. Two important parameters, phase angle andstrain energy release rate, are employed to characterize linear elastic fracture behavior.Similarly nonlinear interface fracture behavior can be characterized by two similarvariables, plastic phase angle and J integral.

Benzer Tezler

  1. Tarihi tuğla duvarların tekstil donatılı harç (TRM) ile güçlendirilmesi

    Retrofitting of historical brick masonry walls with textile reinforced mortar

    PELİN ELİF MEZREA

    Yüksek Lisans

    Türkçe

    Türkçe

    2014

    Deprem Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    PROF. DR. ALPER İLKİ

    YRD. DOÇ. DR. MECİT ÇELİK

  2. Three-dimensional elastic-plastic dynamic fracture analysis for stationary cracks using enriched elements

    Hareketsiz çatlaklar için zenginleştirilmiş elemanlar kullanarak üç boyutlu elastik-plastik dinamik kırılma analizi

    MURAT SARIBAY

    Doktora

    İngilizce

    İngilizce

    2009

    Makine MühendisliğiLehigh University

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. HERMAN F. NIED

  3. Zemin-boru etkileşimi ve gömülü rijit borular üzerindeki toprak yükleri ile ilgili karşılaştırmalı bir inceleme

    A comparative study on soil-pipe interaction and loads on rigid underground conduits

    ERCÜMENT ECE

    Yüksek Lisans

    Türkçe

    Türkçe

    1998

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    Geoteknik Ana Bilim Dalı

    DOÇ. DR. TUĞRUL ÖZKAN

  4. Toz metalurjisi ile üretilmiş Ti-xNB alaşımlarının yüzey özelliklerinin borlama yöntemi ile geliştirilmesi

    Improvement of surface properties of Ti-xNB alloys produced by powder metallurgy with boriding

    BATUHAN SORUŞBAY

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı

    PROF. DR. HÜSEYİN ÇİMENOĞLU

    ÖĞR. GÖR. FAİZ MUHAFFEL

  5. Inconel 718 alaşımının katı partikül erozyon davranışının incelenmesi

    Solid particle erosion of inconel 718 alloy

    BERK BİRCAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2014

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. HÜSEYİN ÇİMENOĞLU