Geri Dön

Effects of labyrinth seals on the stability of rotors

Başlık çevirisi mevcut değil.

  1. Tez No: 401269
  2. Yazar: UĞUR YÜCEL
  3. Danışmanlar: PROF. JACOB Y. KAZAKIA
  4. Tez Türü: Doktora
  5. Konular: Matematik, Mathematics
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2000
  8. Dil: İngilizce
  9. Üniversite: Lehigh University
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 202

Özet

Özet yok.

Özet (Çeviri)

The main objective of this dissertation is to investigate the gas flow in straightthrough labyrinth seals commonly found in high-speed turbomachinery and its effect on the stability of the rotor. In addition the stability of rotor-bearing systems is summarized. The basic equations are derived for compressible flow in a straight-through gas labyrinth seal. The flow is assumed to be completely turbulent in the circumferential direction where the rotor and stator shear stresses are determined by the Blasius correlation in smooth pipes. Zeroth order and linearized first order equations are developed for small motion about a centered position by an expansion in the eccentricity ratio. The zeroth order pressure distribution is found by satisfying the leakage equation while the zeroth order circumferential velocity distribution is determined by satisfying the momentum equation. Several leakage flow models are discussed and compared. A new technique for the calculation of the circumferential velocities is introduced. Periodic solution to the first order equations is obtained for the case of time dependent flow generated by a non-axisymmetric rotation of the rotor. Integration of the resultant pressure and shear stresses along and around the seal defines the reaction force developed by the seal and the corresponding dynamic stiffness and damping coefficients necessary for the lateral stability analysis of the rotor. The results of this analysis are then compared with published experimental measurements, and previous numerical results.

Benzer Tezler

  1. Kademeli labirent seallerde basınç/hız dağılımı, kaçak debisi analizi ve türbomakina rotor dinamiği üzerindeki etkileri

    Pressure/velocity distribution, leakage flow rate analysis in stepped labyrinth seals and the effects on the turbomachinery rotor dynamics

    SEDAT KURUCAN

    Yüksek Lisans

    Türkçe

    Türkçe

    1999

    Makine MühendisliğiEskişehir Osmangazi Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. KEMAL TANER

  2. Gaz türbinli motorlarda kullanılan labirent sızdırmazlık elemanlarında diş eğim açısının sızdırmazlık performansına etkisinin HAD analizleri ile incelenmesi

    CFD investigation of effects of labyrinth seal tooth tilt angle on leakage for gas turbines

    KAYHAN DAĞIDIR

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Makine MühendisliğiKırıkkale Üniversitesi

    Makine Ana Bilim Dalı

    PROF. DR. YAHYA DOĞU

  3. Bal peteği sızdırmazlık elemanında eğimli labirent keçe dişlerinin kaçak debiye etkisinin sayısal incelenmesi

    Numerical investigation of the effect on leakage flow of inclined labyrinth teeth with honeycomb sealing element

    İBRAHİM ZENGİN

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiZonguldak Bülent Ecevit Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ BEYTULLAH ERDOĞAN

  4. Gaz türbinlerinde kullanılan fırça keçe geometrisinin ve çalışma şartlarının kaçak debiye etkisinin HAD analizi ile incelenmesi

    CFD investigation of brush seal leakage depending on seal geometry and operating conditions for gas turbine applications

    AHMET SERHAT BAHAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2016

    Makine MühendisliğiKırıkkale Üniversitesi

    Makine Ana Bilim Dalı

    PROF. DR. YAHYA DOĞU

  5. Düz labı̇rent keçelerde oyuk oluşumunun sızdırmazlık performansına etkisi

    Sealing performance effect of rub groove for straight through labyrinth seals

    UĞURCAN YALÇIN

    Yüksek Lisans

    Türkçe

    Türkçe

    2020

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. KADİR KIRKKÖPRÜ