Nanoparçacık içeren polimerlerin optiksel ve yapısal karakterizasyonlarının incelenmesi
Investigation of optical and structural characterizations of polymers containing nanoparticle
- Tez No: 444777
- Danışmanlar: DOÇ. DR. AHMET ÇETİN, DOÇ. DR. RANA KİBAR
- Tez Türü: Doktora
- Konular: Polimer Bilim ve Teknolojisi, Fizik ve Fizik Mühendisliği, Polymer Science and Technology, Physics and Physics Engineering
- Anahtar Kelimeler: Lüminesans, Mekanik özellikler, Nanokompozitler, Polietilen kompozitleri, Soğurma, Çinko oksit, Luminescence, Mechanical properties, Nanocomposites, Polyethylene composites, Absorption, Zinc oxide
- Yıl: 2016
- Dil: Türkçe
- Üniversite: Celal Bayar Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Fizik Ana Bilim Dalı
- Bilim Dalı: Katıhal Fiziği Bilim Dalı
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmada, Alçak Yoğunluklu Polietilen (AYPE) ürünler, UV stabilizör özelliğine sahip nanoboyutlu Çinko Oksit (ZnO) ve 2-Hydroxy-4-Methoxybenzophenone (BP-3) ile farklı oranlarda katkılandırılmıştır. Bu yeni polimerlerde (nanokompozitlerde) meydana gelen optiksel, yapısal, termal ve mekaniksel değişiklikler detaylı olarak incelenmiştir. Bu amaçla, çekme test ölçümlerine ek olarak XRD, TG-DTA spektrumları ve SEM görüntüleri karakterize edilmiştir. Ayrıca, lüminesent özellikler gösteren ZnO katkılı örnekler radyolüminesans (RL) özellikler bakımından da incelenmiştir. ZnO içeren polietilen nanokompozitlerin hepsi çinko oksitin karakteristik pikini göstermektedir. 390 nm (eksiton) ve 530 nm (ana pik) deki bu karakteristik RL piklerinin şiddeti, kompozite eklenen BP-3 miktarı arttıkça azalmaktayken, ZnO miktarı arttıkça yükselmektedir. Nanokompozitlerde kopmada uzama değeri için BP-3' ün iyileştirmesi ZnO ya göre daha yüksektir fakat diğerlerinde durum tam tersinedir. Nanokompozitlerin termal analizlerinde polietilenin baskın karakterde olduğu gözükmektedir. XRD grafiklerinde nanokompozitlerdeki ZnO oranı arttıkça ZnO nun karakteristik piklerinin daha çok belirginleştiği açıktır. Bu sebeplerden dolayı en verimli olan nanokompozit, ZnO ve BP-3' ün maksimum oranda olduğu numunede elde edilmiştir ve SEM görüntüleri de bu durumu desteklemektedir.
Özet (Çeviri)
In this study, low density polyethylene (LDPE) products were doped in different ratios with 2-Hydroxy-4-Methoxybenzophenone (BP-3) and ZnO which have UV stabilizer properties and nanosized. The optical, electrical, structural, thermal and mechanical changes that are occured in these new polymers (nanocomposites) were studied in detail. For this purpose, besides making tensile testing measurements, in order to find out the optical, structural, mechanical and thermal changes, the new polymer nanocomposites were characterized by XRD, TG-DTA spectra and SEM images. Furthermore, the samples with zinc oxide which show luminescent properties were examined in terms of radioluminescence (RL) features. Radioluminescence spectrum showed characteristic peaks of zinc oxide all of the nanocomposites including ZnO. The intensity of the characteristic RL peaks at 390 nm (exciton peak) and 530 nm (mean peak) increased by increasing rates of nanopowder zinc oxide while adding BP-3 to the composites caused a decrease in intensity of radioluminescence. In mechanical test, for elongation at break, the nanocomposites with BP-3 has better treatment over the nanocomposites with ZnO but in the others have a reverse situation. In thermal analysis of the nanocomposites, PE is dominant over BP-3 and ZnO. The characteristic peaks for ZnO has been more apparent with the raising ratio of ZnO in the nanocomposites in XRD graphs. Because of this reasons, the best yield ratio in the nanocomposite is obtained in the sample of maximum rate of ZnO and BP-3 in the nanocomposite and SEM images also supports this situation.
Benzer Tezler
- Nanoparçacık içeren polimerlerin sürtünme, adhezyon ve mekanik özelliklerinin atomik kuvvet mikroskobisi kullanılarak nanosertlik deneyi yöntemi ile tayini
Determination of friction, adhesion and mechanical properties of polymers containing nanoparticle, by the method of nano-hardness test using atomic force microscopy
MİNE ŞENER
Yüksek Lisans
Türkçe
2014
Kimya MühendisliğiCumhuriyet ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
YRD. DOÇ. MUSTAFA OĞUZHAN ÇAĞLAYAN
- Manyetik ferrit esaslı çekirdek@kabuk nanoparçacık içeren aljinat hidrojel polimerlerin hazırlanması ve karakterizasyonu
Preparation and characterization of alginate hydrogel polymers including core-shell nanoparticle based on magnetic ferrite
ARİF EMRE ŞEN
Yüksek Lisans
İngilizce
2013
Fizik ve Fizik MühendisliğiDumlupınar ÜniversitesiFizik Ana Bilim Dalı
YRD. DOÇ. DR. İLKNUR ÜSTÜNDAĞ
- Supramoleküler ağ yapılı hibrit polimerlerin farklı nanoparçacıklar kullanılarak sentezi ve uygulama alanlarının belirlenmesi
Synthesis and determination of application areas of supramolecular hybrid polymeric networks by using different nanoparticles
İMREN ÖZCAN
- Tasarlanmış ZnO tozların kitosan/polivinil alkol biyobozunur polimerlerin yapısına ve özelliklerine etkilerinin incelenmesi
Investigation of the effects of designed ZnO powders on the structure and properties of chitosan / polyvinyl alcohol biodegradable polymers
YELİZ KÖSE
Doktora
Türkçe
2022
Polimer Bilim ve TeknolojisiEskişehir Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. ENDER SUVACI
- Preparation and characterization of polylactide/poly (butylene adipate-co-terephthalate)/cellulose nanocrystal blend nanocomposites
Selüloz nanokristal içeren polilaktik/poli (bütilenadipat-ko-tereftalat) harman nanokompozitlerin hazırlanması ve karakterizasyonu
DENİZ SEMA SARUL
Yüksek Lisans
İngilizce
2020
Polimer Bilim ve Teknolojisiİstanbul Teknik ÜniversitesiPolimer Bilim ve Teknolojisi Ana Bilim Dalı
DOÇ. DR. MOHAMMADREZA NOFAR