Toz metalurjisi yöntemi ile AISi12-CuAI2 metal matrisli kompozit üretimi ve CuAl2 oranının özelliklere etkisi
Production of AISi12-CuAI2 metal matrix composites and effect of CuAl2 amount to the properties
- Tez No: 457808
- Danışmanlar: DOÇ. DR. YAMAN ERARSLAN
- Tez Türü: Yüksek Lisans
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Alüminyum alaşımları, Alüminyum-silisyum alaşımlar, Metal matrisli kompozitler, Toz metalurjisi, Aluminum alloys, Aluminum-silicon alloys, Metal matrix composites, Powder metallurgy
- Yıl: 2017
- Dil: Türkçe
- Üniversite: Yıldız Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Malzeme Bilim Dalı
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmada toz metalürjisi yöntemleriyle AlSi12 ve CuAl2 tozları üretilmiştir. Bu tozların karışımından CuAl2 oranın değiştirilerek elde edilen metal matrisli kompozitlerin malzeme özelliklerine etkisi deneylerle incelenmiştir. Tozlar mekanik toz üretim yöntemleriyle üretilmiş ve 300 oC'de üç ayrı eksende 10'ar dakika sıcak presleme ile sıkıştırılıp sinterlenmiştir. Farklı oranda CuAl2 içeren numuneleri ışık mikroskobunda incelenmiştir. Numunelerin mikroyapıları incelendiğinde genel olarak homojen bir yapı elde ediğidi gözlemlenmiştir. Bunun ardından Brinell sertlik testi, yoğunluk tayıni ve yüzey aşınma testlerine tabi tutulmuştur. Sertlik testlerindeki analizlerde ise CuAl2 miktarı arttıkça serlik değerlerinin de arttığı gözlemlenmiştir. Yoğunluk tayininde de yine aynı şekilde CuAl2 oranıyla yoğunluk beklediği gibi artmıştır. Tüm bunların yanında, aşınma direncinin de CuAl2'nin artışıyla doğru orantılı olarak arttığı gözlemlenmiştir.
Özet (Çeviri)
In this study, AlSi12 and CuAl2 powders are produced by powder metallurgy process. After, those powders are mixed different amount of CuAl2, and its effect to the material properties is observed. These powders are produced by mechanical methods and all the samples are hot pressed and sintered at 300 oC in three axis, 10 minutes for each axis. All the samples' surfaces that includes different amoun of CuAl2 are observed in light microscope. It is observed that microstructure of samples are homogeneous. Then, all are subjected to brinell hardness test, density determination and surface abrasion tests. I has seen that hardness increases by increasing the amount of CuAl2. Also the result is the same in the density determination as it is expected. Beside all of these, it is clearly seen that the abrasion resistance of material is getting better by incresing the amount of the CuAl2.
Benzer Tezler
- Toz metalurjisi yöntemi ile Ni kaplı GNP takviyeli AlSi12 köpük dolgulu paslanmaz boruların üretimi ve karakterizasyonu
Production and characterization of Ni coated GNP reinforced AlSi12 foam filled stainless pipes by powder metallurgy
KILANI A. MOHAMED HASSAN
Doktora
Türkçe
2025
Metalurji MühendisliğiKastamonu ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. ARİF UZUN
- Östenitik paslanmaz çeliğin bor katkılı Ni3Al ile kaplanabilirliğinin araştırılması
Investigation of boron doped Ni3Al coating of austenitic stainless stell
MEHMET AKKAŞ
Yüksek Lisans
Türkçe
2013
Metalurji MühendisliğiFırat ÜniversitesiMetalurji Eğitimi Ana Bilim Dalı
DOÇ. DR. SERMİN OZAN
- Çok yanıtlı taguchı deney tasarımı yöntemiyle çelik yüzeylerinde oluşturulan termo-kimyasal kaplama özelliklerinin incelenmesi
Investigation of the properties of thermo-chemical coatings formed on steel surfaces by using multi-responsive taguchi experimental design method
ÇİĞDEM CEBECİ
Yüksek Lisans
Türkçe
2025
Metalurji MühendisliğiSakarya Üniversitesiİmalat Mühendisliği Ana Bilim Dalı
PROF. DR. ŞADUMAN ŞEN
- Toz metalurjisi yöntemi ile üretilen Cu-%25Cr elektrik kontak malzemesinin sinterlenme davranışlarının incelenmesi
An Investigation in the sintering behavior of the Cu-25wt%Cr electrical contact materials produced by powder metallurgy technique
HALİL İBRAHİM BAKAN
- Toz metalürjisi yöntemi ile üretilen Al matrisli Al2O3 takviyeli kompozitin sürtünme kaynağının araştırılması
The Investigation of friction welding of Al matrix-Al2O3 reinforced composite produced by powder metallurgy process
ERKAN ŞAHAN
Yüksek Lisans
Türkçe
2002
Makine MühendisliğiFırat ÜniversitesiMakine Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. AHMET HASÇALIK