Geri Dön

Endüstriyel soğutma uygulamalarında ötektik soğutucuların etüdü ve parametrelerinin incelenmesi

Investigation of etude and parameters of industrial cooling applications

  1. Tez No: 501774
  2. Yazar: GÜLENAY ALEVAY KILIÇ
  3. Danışmanlar: DOÇ. DR. ENVER YALÇIN, DOÇ. DR. AHMET ALPER AYDIN
  4. Tez Türü: Doktora
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2018
  8. Dil: Türkçe
  9. Üniversite: Balıkesir Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 125

Özet

Termal enerji depolama sistemlerinden (TED) biri olan gizli ısının depolanması günümüzde soğuk muhafaza uygulamalarında da kullanılmaktadır. Gizli ısı enerjisinin depolanmada birim miktarda depolanan enerji başına daha az hacimle enerji tasarrufu sağladığı için genellikle faz değişim malzemeleri (FDM) kullanılmaktadır. Bu çalışmada soğuk hava deposu, aktif olarak -18°C, 16°C ve -14°C de çalıştırılmıştır. Yapılan deneylerde, yüksüz ve FDM'li kabinlerin rejim sıcaklığına gelmek için harcadığı süreler, kompresör on/off periyodları ve deponun ısınma periyodu mercek altına alınmıştır. Deneyler, üç farklı senaryo ve üç farklı durum için araştırılmıştır. Birinci senaryoda depo, set sıcaklığına soğutulmuş ikinci senaryoda kompresör on/off periyodları 36 saat boyunca incelenmiştir. üçüncü senaryoda ise mekanik soğutma sistemi kapatılarak deponun ısınma süreci incelenmiştir. FDM'nin erime/donma sıcaklığı -7,9°C /-14,7°C olup ticari amaçlı kullanılan ötektik bir karışımdır. Depo içi sıcaklık, bağıl nem, hava hızı, FDM sıcaklık ve dış ortam sıcaklık değerleri 10 sn aralıklarla kayıt altına alınmıştır. Deneylerin belirsizlik, maliyet analizleri ve ekonomik boyutu değerlendirilmiştir. FDM'siz kabinin kompresör on/off süreleri incelenmiş ve stabil kaldığı görülmüştür. FDM'li depoda ise kompresör on/off sürelerinde 36 saat boyunca iyileşme görülmüştür. Üç farklı set değeri için FDM'li deneylerde -18°C ve -16°C'de FDM'nin termal enerjisi sayesinde sistemde oluşan ısı yükündeki kayda değer azalmalar görülmüştür. FDM'li depo FDM'size göre 30 saat sonra kompresör, -18°C set sıcaklığında, 20,73% ve -16°C'de ise %30,09 daha az çalışmıştır. Böylelikle FDM'li kabin bir günde -18°C'de 2 saat, -16°C'de 3,20 daha az enerji tüketerek FDM'nin pozitif etkisi gözlemlenmiştir. Böylelikle FDM'nin erime/donma sıcaklık aralığının hangi kısmında çalışıldığı daha kritik öneme sahip olduğu bu çalışmayla ortaya konmuştur.

Özet (Çeviri)

Storage of latent heat, one of the thermal energy storage systems (TES), is today used in cold storage applications as well. As storage of latent heat provides a lower volume of energy conservation per the unit of stored energy, phase change materials (PCM) are generally used. In this study, a cold storage house has been actively operated at -18°C, -16°C, and -14°C. In the conducted experiments, time periods of neutral cabins with PCM reaching to regime temperature, compressor on/off periods, and heating period of the storage house have been examined. Experiments have been investigated for three different scenarios and three different conditions. In the first scenario, storage room has been cooled to the set temperature; in the second scenario, compressor on/off periods have been monitored for 36 hours. And in the third scenario, mechanical cooling system has been shut down, and heating process of the storage house has been examined. PCM's melting/freezing temperature is -7,9°C /-14,7°C, and is a eutectic mixture used for commercial purposes. Storage temperature, relative humidity, air speed, PCM temperature and outdoor temperature values have been recorded at intervals of 10 seconds. Uncertainty, cost analyses, and economic dimension of the experiments have been evaluated. Compressor on/off period of the cabin without PCM has been examined, and it has been observed to remain stable. In the storage with PCM, an improvement for 36 hours has been observed in compressor on/off periods. In the experiments with PCM for three different set values at -18°C and -16°C, considerable decreases in the heat load in the system due to the thermal energy of PCM have been observed. Compared to the storage without PCM, the storage with PCM operated 19,44% less at -18°C compressor set temperature, and 28,13% less at -16°C compressor set temperature. Thus, as the cabin with PCM consumed less energy for 2 hours at -18°C, and for 3,2 hours and 20 minutes at -16°C in a day, positive effect of PCM has been suggested. Therefore, it has been proved with this study that the part of the PCM melting/freezing temperature range within which the work is performed is of a more critical importance.

Benzer Tezler

  1. Surface modification of stellite hardfacings by post surface melting processes

    Stellite sert dolgu kaplamalar sonrası uygulanan yüzey ergitme prosesleri ile yüzey modifikasyonu

    ALI ABDUL MUNIM ALI ALHATTAB

    Doktora

    İngilizce

    İngilizce

    2021

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ CEVAT FAHİR ARISOY

  2. CO2 akışkanlı soğutma sistemlerinde kullanılan kanatlı borulu ısı değiştiricilerinin termal analizi

    Thermal analysis of fin and tube heat exchangers in refrigeration systems utilising CO2 as a refrigerant

    BİRCE AZERİ

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiGebze Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. ALPER ŞEVKİ KONUKMAN

  3. Corrosion protection of mild steel in cooling water systems with green polymeric inhibitors

    Çevreci polimerik korozyon inhibitörleri ile soğutma sistemlerinde çelik malzemenin korozyonunun önlenmesi

    İPEK ÖZTÜRK

    Doktora

    İngilizce

    İngilizce

    2020

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. ESMA SEZER

  4. Buzdolapları için mikrokanal yoğuşturucu tasarımı

    Microchannel condenser design for refrigerators

    ANIL BAŞARAN

    Doktora

    Türkçe

    Türkçe

    2020

    Makine MühendisliğiManisa Celal Bayar Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ ALİ YURDDAŞ

  5. Use of hydrodynamic stability approach for the calculations of inflow boundary conditions and spread of an axisymmetric turbulent swirling jet

    Hidrodinamik kararlılık analizi ile oluşturulan giriş koşulları kullanılarak çalkantılı sarmal jet akışı benzetiminin yapılması

    AMIR HOSSEIN MEHRABI KERMAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2020

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. İLYAS BEDİİ ÖZDEMİR