Geri Dön

Polimer matriksli karbon nanotüp-cam elyaf takviyeli kompozitlerde çarpma sonrası basma özelliklerinin incelenmesi

Investigation of polymer matrix carbon nanotube-glass fiber-reinforced composites compression after impact properties

  1. Tez No: 513585
  2. Yazar: ERDİNÇ GÜNAYDIN
  3. Danışmanlar: DOÇ. DR. ÖZGÜR DEMİRCAN
  4. Tez Türü: Yüksek Lisans
  5. Konular: Kimya, Metalurji Mühendisliği, Polimer Bilim ve Teknolojisi, Chemistry, Metallurgical Engineering, Polymer Science and Technology
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2018
  8. Dil: Türkçe
  9. Üniversite: Ondokuz Mayıs Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Malzeme Bilimi ve Mühendisliği Bilim Dalı
  13. Sayfa Sayısı: 75

Özet

Bu çalışmada, cam elyaf takviyeli, epoksi matriksli, (karbon nanotüp püskürtülmüş ve püskürtülmemiş olmak üzere iki farklı numune) kompozit plakalar üreterek, kompozit plakalara uygulanan mekanik testlerle, kompozitlerde karbon nanotüp takviyesinin darbe sonrası basma özelliklerine etkisi araştırıldı. Kompozit üretim yöntemi olarak üniversitemiz bünyesinde bulunan 'Reçine Transfer Metodu(RTM)' kullanıldı. Üretilecek her kompozit plaka için dört kat elyaf simetrik olarak üst üste yerleştirildi. Kullanılan elyafların bazılarına toplam reçine ağırlığınca %0,2 Çok Duvarlı Karbon Nanotüp (ÇDKN) püskürtülürken bazıları püskürtülmemiş %0 olarak üretim yapıldı. Üretilen kompozitlere 'Charpy İmpact (Darbe) (CI) ve Darbe Sonrası Basma Testi (CAI)' testleri uygulandı. Ayrıca 'Taramalı Elektron Mikroskopu (SEM)' ile görüntüleri alınan numunelerin kırılma analizleri yapıldı. Sonuç olarak, RTM ile üretim ve karbon nanotüp takviyesiyle, 'Charpy Darbe' testi sonucunda karbon nanotüp takviyeli numunelerin karbon nanotüp takviyesiz numunelere göre yaklaşık %20, 'Darbe Sonrası Basma' testi sonucunda ise yaklaşık %21 oranında daha iyi değerler elde edildi. Kırılma analizlerinde ise kırılmaların ve çatlak yayılmalarının karbon nanotüp takviyeli numunelerde daha az olduğu gözlemlendi.

Özet (Çeviri)

In this study, the effects of carbon nanotube reinforcement on the compression after impact of composites were investigated by producing composite plates of glass fiber reinforced, epoxy matrix (two different samples, carbon nanotubes sprayed and unsprayed).“Resin Transfer Method (RTM)”was used as a method of composite production in our university. For each composite plate to be produced, four layers of fiber were placed symmetrically on top of each other. Some of the fibers used were sprayed with 0,2% Multi-Walled Carbon Nanotube (MWCNT) in total composite plate weight, while some were not sprayed and were produced at 0%. The produced composites were tested with 'Charpy Impact (CI) and Compression After Impact Test (CAI)'. In addition, fracture analysis of the samples taken with 'Scanning Electron Microscope (SEM)' was performed. As a result, RTM production and carbon nanotube reinforcement, the 'Charpy Impact' and 'Compression After Impact' tests resulted in about 20% and 21% better results for carbon nanotube reinforced samples compared to results of the samples without carbon nanotube. In the fracture analyzes, it was observed that cracks and crack propagation were less in carbon nanotube reinforced specimens.

Benzer Tezler

  1. Investigation of mechanical properties of nanoparticle coated glass fiber/epoxy composites coated with dip coating and industrial production methods

    Daldırma ve endüstriyel üretim yöntemleri ile üretilmiş nanoparçacık kaplı cam elyaf/epoksi kompozitlerin mekanik özelliklerinin incelenmesi

    EMİR ÇETİNALP

    Yüksek Lisans

    İngilizce

    İngilizce

    2024

    Mühendislik Bilimleriİstanbul Teknik Üniversitesi

    Nanobilim ve Nanomühendislik Ana Bilim Dalı

    DOÇ. DR. BİRGÜL BENLİ

  2. Karbon nanotüp takviyeli kompozit malzemelerin termal, elektriksel ve mekanik özelliklerinin tespiti

    Determine of thermal, electrical and mechanical properties of carbon nanotube reinforced composite materials

    ONUR AĞMA

    Yüksek Lisans

    Türkçe

    Türkçe

    2015

    Makine Mühendisliğiİstanbul Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. ALAATTİN AKTAŞ

  3. Karbon nanotüp katkısı ile katmanlı cam, karbon ve aramid elyaf takviyeli hibrit kompozit malzemelerin üretimi ve mekanik performanslarının geliştirilmesi

    Production of layered glass, carbon and aramid fiber reinforced hybrid composite materials with carbon nanotube additive and improving mechanical performance

    ERDEM FERİK

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Metalurji MühendisliğiBursa Teknik Üniversitesi

    İleri Teknolojiler Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ CİHAN KABOĞLU

  4. Grafen nanotüp ve cam elyafla güçlendirilmiş LED ile kürlenen polyester kompozit üretiminin araştırılması

    Investigation of production of glass fiber and graphene nanotube reinforced LED curing polyester composite

    AZİME SUBAŞI

    Doktora

    Türkçe

    Türkçe

    2023

    Mühendislik BilimleriDüzce Üniversitesi

    Disiplinlerarası Kompozit Malzeme Teknolojileri Ana Bilim Dalı

    DOÇ. DR. MEHMET EMİROĞLU

    DOÇ. DR. AHMET DEMİR

  5. Development of new generation, high performance polypropylene composites

    Yeni nesil, yüksek performanslı polipropilen kompozitlerin geliştirilmesi

    ORKUN KAYMAKÇI

    Doktora

    İngilizce

    İngilizce

    2021

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. NURSELİ UYANIK