Geri Dön

Dikdörtgen plakların akustik davranışlarının incelenmesi

An investigation on acoustic behavior of rectangular plates

  1. Tez No: 540207
  2. Yazar: FIRAT ERTÜRK
  3. Danışmanlar: PROF. DR. HALUK EROL
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2018
  8. Dil: Türkçe
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Makine Dinamiği, Titreşimi ve Akustiği Bilim Dalı
  13. Sayfa Sayısı: 131

Özet

Tez kapsamında öncelikle plak titreşimlerinin tam olarak anlaşılması ve kullanılması gereken yöntemler gerekçeleriyle birlikte sunulmuştur. Ardından ise bu titreşimlerden kaynaklı ortaya çıkan açık alandaki ses basınçları ve seviyeleri hesaplanmış ve çeşitli yöntemlerle bu sonuçlar karşılaştırılmıştır. Çalışma kapsamında plak akustiği iki farklı sınır şartı altında incelenmiştir. Söz konusu sınır şartlarından birisi; plağın bütün kenarlarının basit mesnetli olması durumudur. Basit mesnetli halde titreşim ve akustik davranışları analitik olarak mevcut durumdadır. Burada literatüre katkı sağlaması açısından problemi monopole kaynaklar ile akustik alanı tekrar oluşturmak hedeflenmiş ve başarıya ulaşılmıştır. Yöntemin tutarlılığı ise bahsedilen mevcut analitik yöntemle karşılaştırılmıştır. İncelenen diğer sınır şartı ise bütün kenarları serbest plak durumudur. Bu durumda plak titreşimleri için analitik tam çözüm mevcut olmayıp yaklaşık yöntemlerin uygulanması gerekmektedir. Dolayısıyla yüzey titreşimlerinden yararlanılarak ortaya atılabilecek herhangi bir tam analitik akustik ifade söz konusu değildir. Bunları göz önüne alarak ve sadece bütün kenarları serbest plaklar için değil aynı zamanda Rayleigh Ritz yönteminde polinomlar kullanılarak ifade edilebilen bütün sınır şartlar için uygulanabilen sonuçlar üretilmiştir. Akustik yayılım formülleri, bir polinomun katsayı ve mertebelerine göre polinom terimlerinin katkılarının toplamı olarak ifade edilebilmiştir ve sonuçlar ANSYS ile birlikte MSC Actran Acoustics hazır sonlu elemanlar paket programlarının sonuçları ile karşılaştırılmıştır ve sonuçların tutarlılığı ortaya konulmuştur.

Özet (Çeviri)

In order to analyze the structure borne acoustical field, one has to analyze the vibration of the boundary surface which is the plate upper surface that induces acoustical waves in the first place if the plate in transverse vibration mode. Thus, vibration analysis methods are introduced first with the justification of each since the analysis are highly dependent on the boundary conditions of the plate. Once the vibration of the plate is well known, one can proceed to acoustical analysis of each vibration mode of the plate. Acoustical fields are calculated for open field environment where there is no reflecting or incoming sound waves and the only source is the plate itself. Sound pressure and sound pressure level (SPL) are the main parameters that are obtained and compared between different methods in this study. Two different boundary conditions are investigated in the scope of this study. Those boundary conditions are all simply supported and all free plate situation. In the case of all simply supported plate, exact analytical vibration and acoustic field formula are available in the literature. The contribution of this study on all simply supported plate is the application of building acoustic field using monopole arrays placed on specific points, minimum amounts and with calculated amplitudes. Results of the monopole superpositions are compared with the analytical results and shown to be trustworthy. Other study on plate is focused on the plate with all edges free. In case of such boundaries, analytical exact solutions are not available for plates and approximate methods should be followed in order to obtain free vibration characteristics of the plate. Method used for vibration analysis is chosen to be Rayleigh Ritz method which is not only applicable for all free plate but also most complicated boundary conditions as well as point spring or/and mass loads. Polinomials are used as basis of the solution in Rayleigh-Ritz Method and acoustical field is calculated for each term of the polinomial that identifies the surface vibration. Thus acoustical formula obtained in this study will be applicable to any kind of boundary conditions of the plate of which the vibration of the surface is charactarised with polynomials. Acoustic formula is based on the constants and orders of each term of the polinomial. Results are compared with ANSYS and MSC Actran Acoustic commercial FEM softwares and results of method proposed shown to be compatible with Finite Element Methods.

Benzer Tezler

  1. A comparative study on optimization in structural acoustics

    Optimizasyonla ilgili karşılaştırmalı inceleme

    MOSTAFA RANJBAR

    Doktora

    İngilizce

    İngilizce

    2011

    Makine MühendisliğiTechnische Universität Dresden

    Makine Mühendisliği Ana Bilim Dalı

    Prof. Dr. STEFFEN MARBURG

  2. Yüzen bir cismin su altı patlamalarına karşı yapısal davranışının nümerik yöntemler ile analizi

    Analysis of the structural behavior of a floatingobject to underwater explosion by numerical methods

    FUAT KABAKCIOĞLU

    Doktora

    Türkçe

    Türkçe

    2023

    Gemi Mühendisliğiİstanbul Teknik Üniversitesi

    Gemi İnşaatı ve Gemi Makineleri Mühendisliği Ana Bilim Dalı

    DOÇ. DR. ERTEKİN BAYRAKTARKATAL

  3. Katmanlı kompozit dikdörtgen plakların burkulma ve titreşim analizi

    Buckling and vibration analysis of laminated composite rectangular plates

    METİN AYDOĞDU

    Doktora

    Türkçe

    Türkçe

    2003

    Makine MühendisliğiTrakya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. TANER TIMARCI

  4. Çapraz tabakalı kompozit dikdörtgen plakların dinamik analizi

    Dynamic analysis of rectangular cross-ply laminated composite plates

    NİHAN SATIR

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. FETHİ KADIOĞLU

  5. Tabakalı kompozit dikdörtgen plakların değiştirilmiş uygun doğrultular metodu'na göre optimizasyonu

    Optimization of laminated composite plates using modified feasible direction method

    UMUT TOPAL

    Doktora

    Türkçe

    Türkçe

    2008

    İnşaat MühendisliğiKaradeniz Teknik Üniversitesi

    İnşaat Mühendisliği Bölümü

    PROF. DR. ÜMİT UZMAN