Beton dayanımının su/çimento ve agrega/çimento oranlarına bağlı olarak belirlenmesi
Determination of strenght of concrete depending on the water to cement and agrega to cement ratios
- Tez No: 575072
- Danışmanlar: PROF. DR. ADNAN ÇOLAK
- Tez Türü: Yüksek Lisans
- Konular: Mimarlık, Architecture
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: Türkçe
- Üniversite: Trakya Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Mimarlık Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 48
Özet
:Beton; su, çimento, agrega, çimento ve bazı mineral ya da kimyasal (akışkanlaştırıcı, geciktirici, hava sürükleyici gibi) katkı maddelerinden oluşan kompozit bir malzemedir. İstenilen özelliklere sahip bir beton elde edebilmek için betonu oluşturan malzemelerin özelliklerinin ve karışım oranlarının belirlenmesi gerekir. Beton karışım oranlarını belirlemede genellikle Graf, Bolomey, Feret ve Abrams modelleri kullanılmaktadır. TSE tarafından hazırlanan TS 802 standardında bu modellere atıf yapılmaktadır. Bu çalışma kapsamında literatürde yer alan beton dayanım formülleri incelenmiştir. Yapı merkezi, Arıoğlu, Türkel ve Çolak formülleri ulusal çalışmalar, DeLarrard, Neville, ve Popovich'in bağıntıları ise uluslararası çalışmalar başlığı altında açıklanmıştır. Yapılmış çalışmalarda yer alan modeller genellikle beton dayanımını su/çimento oranına ve beton içindeki hava miktarına bağlı olarak tahmin etmektedir. Bu modeller beton dayanımını önemli ölçüde etkileyen parametrelerden biri olan agrega/çimento oranını dikkate almamaktadır. Bu nedenle bu çalışmada beton dayanımını, su/çimento ve agrega/çimento oranlarına bağlı olarak belirleyen Çolak modeli incelenmiştir. Çolak tarafından geliştirilen bu modelin deneysel sonuçlara uyumu araştırılmış ve diğer modellerle karşılaştırılması yapılmıştır. Elde edilen sonuçlar Çolak modelinin beton dayanımını tahmin etmede oldukça başarılı olduğunu göstermektedir. Model ayrıca maksimum basınç dayanımını veren su/çimento oranının hesaplanmasına olanak sağlamaktadır.
Özet (Çeviri)
: Concrete is a composite material consisting of water, cement, aggregate and some mineral or chemical additives (such as fluidizer, retarder, air entrainment). In order to include concrete with the intended properties, the properties of the materials forming the concrete and the mixing ratios should be determined. Generally, Graf, Bolomey, Feret and Abrams models are used to determine concrete mix ratios. These models are cited in TS 802 standard prepared by TSE. In this study, concrete strength formulas in the literature are examined. The national studies such as the formulas in the works of Arıoğlu, Türkel, and Çolak, and many international studies such as De Larrard, Neville and Popovich relations were explained. With these models, the concrete strength can be estimated depending on the water/cement ratio and the amount of air in the concrete. However, these models do not take into account the aggregate/cement ratio which is one of the important parameters affecting concrete strength. For this reason, in this study, Çolak model is used for determining the strength of the concrete depending on the water/cement and aggregate/cement ratios. This study is aimed to research the agreement between the experimental results and calculated values by Çolak model. The model in question is also compared with other models. The data obtained in this study show that Çolak model is very successful for the estimation of the strength of concrete. The model also allows the determination of the water/cement ratio which gives the maximum strength of the concrete.
Benzer Tezler
- Farklı kökenli agregalarla üretilmiş normal ve yüksek mukavemetli betonlarda agrega konsantrasyonunun mekanik özelliklere etkisi
Effects of aggregate volume fraction on mechanical properties of normal and high strength concrete produced with aggregate from different origins
ADİL ORÇUN KAYA
Doktora
Türkçe
2017
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. HASAN YILDIRIM
- Çelik lif donatılı betonların performansa dayalı tasarımı ve optimizasyonu
Optimization and performance based design of steel fiber reinforced concretes
MUHSİN YALÇIN
Doktora
Türkçe
2009
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. CANAN TAŞDEMİR
- Mikronize kalsit katkı ile üretilen betonların basınç dayanımının deneysel olarak araştırılması
Experimental investigation of the compressive strength of concrete produced with micronized calcite additive
MİKAİL KURU
Yüksek Lisans
Türkçe
2023
İnşaat MühendisliğiKTO Karatay Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ ABDULKERİM İLGÜN
- Kendiliğinden yerleşen beton üretiminde uçucu kül ve mermer tozu kullanımının araştırılması
Investigation of the use of fly ash and marble powder in self-compacting concrete production
MOHAMED H T ZARROG
Yüksek Lisans
Türkçe
2020
İnşaat MühendisliğiKastamonu ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ SELÇUK MEMİŞ
- Nano silikanın yüksek oranda uçucu kül içeren betonların taze hal, priz süresi ve mekanik ozellikleri üzerine etkisinin araştırılması
Investigation on the effect of nano-silica on the fresh state, setting times and mechanical properties of concrete with high fly ash content
AHMET BARAN
Yüksek Lisans
Türkçe
2022
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. HAKAN NURİ ATAHAN