Geri Dön

Geri dönüştürülmüş agregaların harç özelliklerine etkisi

The impact of recycled aggregates on the features of mortar

  1. Tez No: 611886
  2. Yazar: MUSTAFA GÜMÜŞSOY
  3. Danışmanlar: PROF. DR. OSMAN GENÇEL
  4. Tez Türü: Yüksek Lisans
  5. Konular: İnşaat Mühendisliği, Civil Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2019
  8. Dil: Türkçe
  9. Üniversite: Bartın Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 79

Özet

İnşaat sektöründe en çok kullanılan ve en fazla atık oluşturan yapı malzemesi betondur. Beton üretiminde büyük oranda doğal kaynaklar kullanılmaktadır. Beton üretimiyle beraber kullanılan agrega miktarı artmakta ve bunun sonucunda kullanılabilir agrega rezervleri zamanla tükenmektedir. Bunun sonucunda da agrega ihtiyacının temininde sıkıntıların oluşacağı aşikârdır. Bu nedenle özellikle beton kullanımının fazla olduğu yerleşim bölgelerinde agrega temini için yeni çareler gerekmektedir. Doğal kaynaklar zamanla tükenirken, kentsel dönüşüm ve yeniden yapılaşma ile beraber çevresel kirlilik artmaktadır. Bu sebepten sürdürülebilir hayatta inşaat yıkıntı atıklarının çevreye verdiği zararı göz önüne aldığımızda geri kazanılmış agreganın kullanılması zorunlu kılınmaktadır. Beton endüstrisinde geri dönüşümlü malzeme kullanımı, tabii hammadde kullanımını azaltacağından dolayı ve aynı zamanda çevresel atıkları da en aza indireceği için iyi bir çözüm olacaktır. Yapılan bu çalışmada, beton atıklarından çeşitli işlemler sonucu elde edilen iri ve ince agreganın geri dönüşüm agregası olarak harç üretiminde kullanım olanakları araştırılmıştır. Geri dönüştürülmüş agregaların harç üretimine etkisinin gözden geçirildiği bu çalışmada standart CEN kumu yerine, %0, %25, %50, %75 ve %100 oranlarında geri dönüştürülmüş beton agregası (GDA) kullanılarak harç numuneler oluşturulmuştur. Üretilen harçlar, kalıplara doldurularak katılaşması için 24 saat beklenmiştir. Daha sonra kalıptan çıkarılan numunelere hava kürü uygulanmıştır. Üretilen harç numuneleri üzerinde kıvam tayini, birim hacim ağırlık, eğilme ve basınç dayanımı, ultrases geçiş süresi, su-emme oranı, kapilarite, aşınma (böhme) deneyi, elastisite modülü tayini ve donma-çözülme incelemeleri yapılmıştır. GDA oranının artması ile birlikte, numunelerin basınç ve eğilme dayanımları azalmıştır. GDA oranının artmasıyla numunelerin kılcallık katsayı değerleri, su emme kapasiteleri ve kuruma büzülmeleri de artmıştır. Ayrıca GDA oranını yükseltmek aşınma dayanıklılıklarını da arttırmıştır.

Özet (Çeviri)

The construction material which is mostly used in the construction sector and creates the most waste is the concrete. The natural sources are used in the generation of concrete. The amount of aggregate which is used increases with the generation of concrete so the useable aggregate reserves give out in time. As a result of this situation, it is clear that the problems will be seen in the supply of aggregate need. Thus, the new remedies are essential for the supply of aggregate in the dwellings zones especially where the use of concrete is too much. As these natural sources give out in time, so the environmental pollution increases with the urban transformation and reengineering. Thus, when we consider the harm of building wreckage waste on the environment in the sustainable life, it requires that the recycled aggregate is used. As the use of recycled material in the concrete industry will decrease the use of natural rawmaterial and also, will minimize the environmental wastes, it will be a well solution. In this study, the possibilities of using coarse and fine aggregate obtained from concrete wastes as a result of various processes in recycling mortar production were investigated. The samples were made with the use of recycled aggregates (RA) at the rates of 0%, 25%, 50%, 75% and 100% instead of the standard aggregate in this concept that the recycled aggregates' impact on the generation of mortar is reviewed. The obtained mortars were waited for 24 hours in order that they make the set, after they were filled in the templates. After that, the air cure was implemented to the samples which were taken from the template. The reviews of consistency designation, unit-volume weight, bending and compressive strength, ultrasonic pulse duration, water-absorption rate, capillarity, abrasion expression, elasticity module designation and freezing-dissolve were made on the generated mortars. The samples' compressive and bending strength decreased to the contrary with the increase of RA's rate. The samples' capillarity coefficient values, water-abrasion capacity and desication-contraction increased with the increase of recycled aggregate rate. Moreover, to raise RA's rate increased the abrasion strength.

Benzer Tezler

  1. Improvement of the quality of recycled fine aggregates by microbial induced calcium carbonate precipitation

    Geri dönüştürülmüş ince agregaların özelliklerinin mikrobiyal kalsiyum karbonat çökelmesi ile iyileştirilmesi

    EKİN ARIKAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2024

    Çevre MühendisliğiHacettepe Üniversitesi

    Çevre Mühendisliği Ana Bilim Dalı

    DOÇ. DR. YUSUF ÇAĞATAY ERŞAN

  2. Metakaolin ve geri dönüştürülmüş beton agregası kullanılarak üretilen geopolimer harçların fiziksel ve mekanik özelliklerinin araştırılması

    Investigation of the physical and mechanical properties of geopolymer mortars manufactured using methaolin and recycled concrete aggregate

    FUNDA AL

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    İnşaat MühendisliğiMunzur Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DOÇ. DR. NİHAN GÜLMEZ

  3. Geri dönüştürülmüş agregaların harç üretiminde kullanılabilirliğinin incelenmesi

    Investigation on the utilization of recycled aggregates in mortar production

    MUSTAFA ŞAHİN

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    İnşaat MühendisliğiKaradeniz Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ ŞİRİN KURBETCİ

  4. Green and digital transformation towards circular economy in the construction industry: Upcycling of construction and demolition wastes from diverse sources and their integration into 3D printing technology

    İnşaat endüstrisinde döngüsel ekonomiye doğru yeşil ve dijital dönüşüm: Farklı kaynaklardan elde edilen inşaat yıkıntı atıklarının ileri dönüştürülmesi ve 3D baskı teknolojisine entegrasyonu

    ANIL KUL

    Doktora

    İngilizce

    İngilizce

    2024

    İnşaat MühendisliğiHacettepe Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DOÇ. DR. GÜRKAN YILDIRIM

  5. Genleştirilmiş camın hafif beton agregası olarak değerlendirilmesi

    Evaluation of the expanded glass as a light concrete aggregate

    SEMA GÜLENGÜL

    Yüksek Lisans

    Türkçe

    Türkçe

    2020

    Kimya MühendisliğiFırat Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. FİLİZ KAR