Geri Dön

Design and flexural behaviour of sandwich panelswith 2d composite skins and 3d woven cellularcore (3dwcc)

Başlık çevirisi mevcut değil.

  1. Tez No: 719165
  2. Yazar: ELİF KALKANLİ
  3. Danışmanlar: Belirtilmemiş.
  4. Tez Türü: Doktora
  5. Konular: Metalurji Mühendisliği, Mühendislik Bilimleri, Metallurgical Engineering, Engineering Sciences
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2020
  8. Dil: İngilizce
  9. Üniversite: The University of Manchester
  10. Enstitü: Yurtdışı Enstitü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 153

Özet

Özet yok.

Özet (Çeviri)

Design and Flexural Behaviour of Sandwich Panels with 2D Composite Skins and 3D Woven Cellular Core (3DWCC) Doctor of Philosophy in the Faculty of Science and Engineering 2020 Elif Kalkanli School of Materials The use of composites has widely increased over the years. These structures have particularly attracted the attention of the aerospace industry where the low weight is one of the important features of structural design. Then, the composites have been started to use in sandwich panels. There have been many implementations of the composites in the sandwich panels due to their structural efficiency with the low weight. The aim of this research is to investigate a novel three-dimensional woven cellular core (3DWCC) for application in morphing wing for unmanned aerial vehicles. Polyester yarn is used as reinforcement and the epoxy as matrix. In order to characterise their mechanical properties, the composite cores are tested under compression in 1- and 3- directions. Then, the 3D woven composite core performance, which the cells lie in 1- direction (longitudinal), is investigated under four-point bending. The effect of skin thickness, the core topology and the core type are examined experimentally. One of the key results obtained from the experiments is that the 3DWCC, which the cells lie in 1-direction, recover their shape after the load is removed in both compression and flexural tests. In addition, the 3D woven cellular core (3DWCC) shows resistance to the bending without skin. The flexural behaviour of the sandwich panels is highly affected from the geometrical parameters of the core and skin. In this line, failure modes of the 3D woven cellular core panels and their limit loads are predicted analytically depending on variables: the skin thickness, core density, and loading configuration.

Benzer Tezler

  1. 3B eklemeli üretim yöntemiyle üretilmiş hücresel kafes yapılı sandviç panellerin mekanik davranışlarının incelenmesi

    Investigation of mechanical behavior of sandwich panels with lattice structure produced by 3D additive manufacturing method

    NECATİ ERCAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiBursa Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ DORUK ERDEM YUNUS

  2. In-plane behavior of sandwich panels

    Sandviç panellerin düzlem içi davranışı

    AMIRMAHDI MOHAMMADI SAGHAYESH

    Yüksek Lisans

    İngilizce

    İngilizce

    2017

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Ana Bilim Dalı

    DOÇ. DR. ERCAN YÜKSEL

  3. Mechanical response of the carbon fiber reinforced polymer composite sandwich structures with pyramidal lattice core

    Piramit kafesli nüveye sahip karbon elyaf takviyeli kompozit bir sandviç yapının mekanik cevabı

    GÜRKAN ÖNAL

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Havacılık Mühendisliğiİstanbul Teknik Üniversitesi

    Uçak ve Uzay Mühendisliği Ana Bilim Dalı

    PROF. DR. ZAHİT MECİTOĞLU

  4. Composite materials for wind energy applications

    Rüzgar enerjisi uygulamaları için kompozit malzemeler

    CİHAN KABOĞLU

    Doktora

    İngilizce

    İngilizce

    2017

    Makine MühendisliğiImperial College London

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. JOHN P DEAR

  5. Numerical and experimental investigation on the crushing behaviour of auxetic lattice cells produced with additive manufacturing techniques

    Eklemeli imalat teknikleri ile üretilmiş ökzetik kafes yapıların ezilme davranışlarının nümerik ve deneysel olarak incelenmesi

    KADİR GÜNAYDIN

    Doktora

    İngilizce

    İngilizce

    2020

    Havacılık Mühendisliğiİstanbul Teknik Üniversitesi

    Uçak ve Uzay Mühendisliği Ana Bilim Dalı

    PROF. DR. HALİT SÜLEYMAN TÜRKMEN

    DR. ÖĞR. ÜYESİ ANTONIO MATTIA GRANDE