Sinterlenmiş CR23C6 karbür tozunun difüzyon kaynağı yöntemi ile yüzey kaplama malzemesi olarak araştırılması
Investigation of sintered Cr23C6 powder as surface coating materyal
- Tez No: 90624
- Danışmanlar: DOÇ. DR. NURİ ORHAN
- Tez Türü: Yüksek Lisans
- Konular: Eğitim ve Öğretim, Metalurji Mühendisliği, Education and Training, Metallurgical Engineering
- Anahtar Kelimeler: Difüzyon kaynağı, Karbür, Sinterleme, Yüzey kaplama malzemeleri, Diffusion welding, Carbide, Sintering, Surface coating materials
- Yıl: 1999
- Dil: Türkçe
- Üniversite: Fırat Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Metalurji Eğitimi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
nı ÖZET Yüksek Lisans Tezi IIŞ Cr23C6 KARBÜR TOZUNUM DIFÜZYON IW Sİ İLİ VAHDETTİN KOÇ Fırat Üniversitesi Fen Bilimleri Enstitüsü letalurjî Eğitimi ÂnabiHim Dalı 1999 Sayfa: 79 Bu çalışmada ferrokrom tozlarının yüzey kaplama malzemesi olarak kullanılıp kullanılmayacağı araştırılmıştır. Bu maksatla Elazığ ferrokrom tesislerinden temin edilen tozlar, demir tozları ile %5,10,20 oranlarında ve bağlayıcı olarak da Ni ve Co kullanılarak sinterlenmiş. Elde edilen kompozit AISI 1010' dan parçalara difüzyon kaynağı yolu ile 1100 °C de basınç altında birleştirilerek, birleşme arakesitinin özellikleri incelenmiştir.VI As a result it was found that wear - resistance plates could be produced using ferro-chromium powder (Yıldırım, 1999) and these plates could be bonded with low C steels safely with diffusion bonding. n In the first chapter of the study, the subject was introduced, the powder metallurgy, ferro-chromium, solid-state boding methods in were discussed in the second, third and fourth chapters respectively. In the fifth chapter the experimental studies, in the sixth chapter the results of experiments were given. In the seventh and final chapter, the condusions and recommendations were presented.
Özet (Çeviri)
SUMMARY tester Thesis INVESTIGATION OF SINTERED Cr23C6 POWDER AS SURFACE COATING MATERYAL VAHDETTİN KOÇ Fırat University Graduate School of Natural and Applied Sciences Department of Metallurgy Education 1999, Page: 79 in this study, usability of ferro-chromium powders as surface coating materials was investigated. With this aim powder provided from Elazig Ferro-Chromium Plant was mixed with iron powders having 2 %Co and then 2 %Ni, in proportions of 5, 10, and 20 percent. This mixtures were compacted under a load of 18 ton and sintered at 1100°C for 60 minutes. The composites produced were diffusion-bonded with AISI 1010 rectangular bars under bonding pressures of 2,5 MPa in 60 minutes. The bonding interface of the diffusion couples (AISI 1010-Cornposite) were examined with optical microscope, EDS, SEM and the hardness distributions were determined with Vickers Hardness Scale using a load of 3 Kg.VI As a result it was found that wear - resistance plates could be produced using ferro-chromium powder (Yıldırım, 1999) and these plates could be bonded with low C steels safely with diffusion bonding. n In the first chapter of the study, the subject was introduced, the powder metallurgy, ferro-chromium, solid-state boding methods in were discussed in the second, third and fourth chapters respectively. In the fifth chapter the experimental studies, in the sixth chapter the results of experiments were given. In the seventh and final chapter, the condusions and recommendations were presented. ©OKÛMANTASYON MERKEZÎ
Benzer Tezler
- Sinterlenmiş gözenekli bronz yatak üretiminde yeni bir yöntem
Başlık çevirisi yok
S. FERDA ÖZDER
Yüksek Lisans
Türkçe
1986
Makine MühendisliğiKaradeniz Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. FAZLI ARSLAN
- Sinterlenmiş bronz esaslı kaymalı yataklarda polimer kullanımının tribolojik özelliklere etkisi
The effect to tribolojical properties of use polymer in sintered bronze-based plain bearins
KADİR GÜNGÖR
Doktora
Türkçe
2016
Makine MühendisliğiSakarya ÜniversitesiMakine Eğitimi Ana Bilim Dalı
PROF. DR. İBRAHİM ÖZSERT
DOÇ. DR. AHMET DEMİRER
- Sinterlenmiş Tİ-6Al-4V alaşımının mekanik özelliklerinin incelenmesi
Investigation of mechanical properties of sintered TI-6Al-4V alloy
ENİS CANTEMÜR
Yüksek Lisans
Türkçe
2025
Makine MühendisliğiSivas Cumhuriyet ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. AHMET AKKUŞ
DR. ÖĞR. ÜYESİ ÖMER KARABEY
- İndüksiyonla sinterlenmiş 316l paslanmaz çelik malzemelerin mekanik karekterizasyonu
Mechanical characterization of induction sintered 316l stainless steel materials
MUSTAFA YASHAR JUMAAH SHWRBA
Yüksek Lisans
Türkçe
2023
Makine MühendisliğiOndokuz Mayıs ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. NACİ KURGAN
- Yüksek sıcaklıkta sinterlenmiş alümina (Al2O3) seramiklerin karakterizasyonu ve nötron radyasyonunun malzeme özelliklerine etkisinin araştırılması
Characterization of alumina ceramics sintered at high temperature and investigation of neutron radiation effect on the material properties
ERDEM UZUN
Yüksek Lisans
Türkçe
2001
Fizik ve Fizik MühendisliğiYıldız Teknik ÜniversitesiFizik Ana Bilim Dalı
DOÇ.DR. YASEMİN YARAR